AECMA PREN 4049-001-2004 Aerospace Series Thermocouple Extension Cable Operating Temperatures between -65 Degrees C and 260 Degrees C Part 001 Technical Specification Edition P 1《航.pdf

《AECMA PREN 4049-001-2004 Aerospace Series Thermocouple Extension Cable Operating Temperatures between -65 Degrees C and 260 Degrees C Part 001 Technical Specification Edition P 1《航.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 4049-001-2004 Aerospace Series Thermocouple Extension Cable Operating Temperatures between -65 Degrees C and 260 Degrees C Part 001 Technical Specification Edition P 1《航.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、AECMA STANDARD NORME AECMA AECMA NORM Edition approved for publication 30 September 2004 prEN 4049-001 Edition P 1 September 2004 Comments should be sent within six months after the date of publication to AECMA-STAN ICs: 49.060 Descriptors: ENGLISH VERSION Aerospace series Thermocouple extension cab

2、le Operating temperatures between - 65 OC to 260 OC Part O01 : Technical specification Srie arospatiale Luft- und Raumfahrt Tempratures de fonctionnement comprises Betriebstemperaturen Cbles, thermocouple Thermoelement Ausgleichsleitung entre - 65 OC et 260 OC Partie O01 : Spcification technique zwi

3、schen - 65 OC und 260 OC Teil O01 : Technische Lieferbedingungen This “Aerospace Series“ frestandard has been drawn up under the responsibility of AECMA-STAN (The European Association of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has

4、 been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this frestandard, the technical content shall not be changed to an extent that interchangeabilify is affected, physically or functionally, without re-identification of the st

5、andard. After examination and review by users and formal agreement of AECMA-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implemen

6、t the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Electrical Domain I I Copytight 2004 O by AECMA-STA1 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under licens

7、e with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 2 prEN 4049-001 :2004 Foreword This standard was reviewed by the Domain Technical Coordinator of AECMA-STANS Electrical Domain. After inquiries and votes carried out in accordance with the rules of AE

8、CMA-STAN defined in AECMA- STANS General Process Manual, this standard has received approval for Publication. Contents 1 2 3 4 4.1 4.2 4.3 4.3.1 4.3.2 4.3.3 5 6 7 7.1 7.1.1 7.1.2 7.1.3 7.1.4 7.2 7.2.1 7.2.2 7.2.3 7.2.4 8 9 9.1 9.2 Scope Norm at ive referen ces Definitions and symbols Materials and c

9、onstruction Conductors Materials Construction of the cables General Cable lay Screened cables Required characteristics Tests method Quality assurance Qualification General requirements Qualification conditions Qualification tests Extension of qual if cat ion Acceptance tests Required conditions Prod

10、uction routine tests Tests prior to delivery Periodic tests Identification marking Packaging, labelling and delivery length Packaging and labelling Delivery length Page 3 3 3 3 3 4 4 4 4 4 5 6 8 8 8 8 9 9 9 9 9 9 9 10 10 10 10 Copyright Association Europeene des Constructeurs de Materiel Aerospatial

11、 Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 3 prEN 4049-001 :2004 Minimum elongation 1 Scope Minimum breaking strength This standard specifies the required characteristics, test methods, qualification and acceptance

12、 conditions of thermocouple used for the connection between the thermocouple and the equipment. Strand dia. 0,151 mm 15 15 2 Normative references Strand dia. 0,20 mm Strand dia. 0,151 mm Strand dia. 0,20 mm 15 10,2 17,7 15 9,7 16,7 This European Standard incorporates by dated or undated reference, p

13、rovisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in

14、it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). IS0 2574: 1994, Aircraff - Electrical cables - Identification marking IS0 8056-1 :I 985, Aircraff - Nickelchromium and nickel-aluminium thermocouple extension cables

15、- Part 7: Conductors - General requirements and tests IS0 8815, Aircraff - Electrical cables and cable harnesses - Vocabulary EN 3475-1 O0 *, Aerospace series - Cables, electrical, aircraff use - Test methods - Part 700: General EN 9133, Aerospace series - Quality management systems - Qualification

16、Procedure for Aerospace Standard Parts EN 60584-2, Thermocouples -Part 2: Tolerances 3 Definitions and symbols See EN 3475-100, IS0 8056-1 and IS0 8815. 4 Materials and construction 4.1 Conductors The conductors for cables in accordance with the present Technical Specification shall consist of condu

17、ctors as per IS0 8056-1. The tolerance class is according to EN 60584-2. Individual strands shall show the following minimum elongation and tensile strength (see Table 1). Table 1 * 1) All parts quoted in this standard Published as AECMA Prestandard at the date of publication of this standard Copyri

18、ght Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 4 prEN 4049-001 :2004 4.2 Materials The insulation shall be of regular, circular cross-section throughou

19、t the entire length of the cable. The surface of the cable shall be smooth and comply with the requirements in respect of identification. The materials used shall be unaffected by corrosion and shall be resistant to the effects of mould fungus and similar micro-organisms. 4.3 Construction of the cab

20、les 4.3.1 General The operating temperature of the wires shall not be lower than the maximum operating temperature of the complete cable. 4.3.2 Cable lay The lay length of the outer layer shall not be less than 8 times and not more than 16 times the nominal diameter of the cable. The core shall not

21、be spliced. 4.3.3 Screened cables 4.3.3.1 General The individual strands used for the screen shall be free from kinks, loops or breaks; their surface shall be free from corrosion and other contamination. They shall satisfy the mechanical tests in EN 3475-505 to EN 3475-508 before use. The screen sha

22、ll be in contact with all the cabled cores. Where spiral screening is used the lay direction shall be contrary to that of the cables cores. 4.3.3.2 Joints Joints in the individual strands of the screen shall be made by soldering or by laying the individual strands together over a length of at least

23、1 O mm. There shall be no more than one joint per 3 m cable length (measured between different individual strands). 4.3.3.3 Braid screen pushback capability In accordance with test 6.41. 4.3.3.4 Angle of spiral screening or braiding The angle y of spiral screening or braiding (as shown in Figure I),

24、 measured against the longitudinal axis of the cable shall be at least IO“. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 5 prEN 4049-001 :2004

25、4.3.3.5 Screen coverage The screen shall have a coverage of at least 90 % for spiral screening and at least 85 % for braiding, these values being determined by the following formula: s= D= d= N= n= B= z= F= = u= U = Y= a= lay length of screen in mm diameter under screen in mm (for cables with 2 or m

26、ore cores without fillers: diameter of screen strand in mm number of cores number of strands per carriers diameter of core in mm total number of carriers filling factor optical coverage see Figure 1. nd / sin a see 4.3.3.4. 90” -y D=(z+N) b/z Figure 1 - Cable covering The screen coverage is calculat

27、ed using the following formula: - for spirals: U=z(D+d) and S=z(D+d)tana F = UZ / U= nd Z/ z (D + d) sin a =Fx100(%) - for braids: U=z(D+d) and S=z(D+2d)tancx For braids, the filling factor F and coverage , taking into account both braiding directions and a symmetrical braiding pattern are: F= (U/ U

28、) (Z/ 2) = nd / z (D+ d) sin a (Z/2) =F(2 -fl x 100 (%) 5 Required characteristics The characteristics of the cables, tested according to the methods described hereafter shall comply with the values given in the product standard. Copyright Association Europeene des Constructeurs de Materiel Aerospat

29、ial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 6 prEN 4049-001 :2004 7 6 Tests method See Table 2. Table 2 - Tests: methods, application, requirements 1 3 3 3 3 3 3 3 Tests X 6.10 Accelerated ageing 6.1 1 Shrinkage

30、and delamination 6.12 Delamination and blocking 6.13 Thermal shock 6.14 6.15 Bending at ambient temperature Cold bend test 5 Q) TI O ._ - i- O a ._ L Requirements (and/or particulars) EN 3475- (and/or particulars) X - X - Test conditions Visual examination 1 O0 201 Product standard 6.2 Mass 202 mini

31、mum length 0,5 m X - X Product standard - X 6.3 I Dimensions 203 Product standard Ohmic resistance per unit 64 length 30 1 X - X - X Product standard 6.5 302 Alternative to dry test Voltage proof test: - immersion test - dry test - or dry impulse test Insulation resistance at (20 f 2) “C: at (95 f 2

32、) “C: 13 KV r.m.s. 13 KV r.m.s. 33 KV peak voltage 6.6 303 For 1 Km length 1 500 MQ 1 MQ 6.7 I Surface resistance 304 NOT APPLICABLE 6.8 I Overload resistance 305 NOT APPLICABLE 6.9 I Continuity of conductors 306 X 401 Mandrel 0 and test load: Table 3 X 402 Temperature: product standard X - X Produc

33、t standard 403 Mandrel diameter: Table 3 Temperature: product standard Product standard 404 Temperature: product standard X Product standard X - X 405 Mandrel diameter: Table 3 406 Mandrel 0 and test load: Table 3 Temperature: product standard Product standard 6.16 I Flammability 407 X - Product sta

34、ndard continued Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 7 prEN 4049-001 :2004 Table 2 - Tests: methods, application, requirements (continu

35、ed) Tests Clauses N“ Requirements (and/or particulars) EN 3475- (and/or particulars) Description 6.17 Fire resistance 408 6.18 6.19 Air-excluded ageing Thermal endurance 409 41 O NOT APPLICABLE NOT APPLICABLE 6.20 Resistance to fluids 41 1 Per fluid tested 6.21 Humidity resistance 412 Method A or B

36、as requested in product standard 6.22 Wrap back test 413 4pplicable to cables 5 5 mm2 6.23 Differential scanning calorimeter (DSC test) 414 6.24 Dynamic cut through 501 Temperature: product standard roduct standard 6.25 Notch propagation 502 Cut depth: product standard roduct standard 6.26 Scrape ab

37、rasion 503 Load: product standard 3equirement to be considered at 20 “C unless otherwise specified 6.27 Torsion 4pplicable to 5 5 mm2 504 Test load: Table 3 r3 and T4: product standard 505 6.28 See 4.1 of this standard Tensile test on conductors and strands 6.29 6.30 Plating continuity Adherence of

38、plating 506 507 NOT APPLICABLE NOT APPLICABLE 6.31 6.32 Plating thickness Solderability 508 509 NOT APPLICABLE NOT APPLICABLE 6.33 51 O NOT APPLICABLE Tensile strength and elongation of extruded insulation, sheath and jacket material Cable-to-cable abrasion 6.34 51 1 roduct standard 6.35 6.36 Flexur

39、e endurance Smoke density 51 2 601 roduct standard roduct standard 6.37 6.38 Toxicity Resistance to wet arc tracking 602 603 roduct standard NOT APPLICABLE 6.39 Resistance to dry arc propagation 604 NOT APPLICABLE continued Copyright Association Europeene des Constructeurs de Materiel Aerospatial Pr

40、ovided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 8 prEN 4049-001 :2004 6.40 Table 2 - Tests: methods, application, requirements (concluded) Wet short circuit test 605 I Tests 6.43 6.44 Permanence of 703 manufacturers markin

41、g Flexibility 704 6.41 6.45 6.46 6.42 Contrast measurement 705 Laser markability 706 Strippability and adherence of insulation to the conductor 6.47 6.48 701 Magnetic properties IS0 8056-1 Thermo electric test IS0 8056-1 Screen pushback capability Nominal conductor cross-section mm2 0,4 0,6 702 Corr

42、esponding size Mandrel diameter Test force AWG a mm N 9 10 12 x max. cable diameter 22 20 4- Number of specimens per cross section for each test unless otherwise specified I Requirements (and/or particulars) Product standard Product standard Product standard Product standard Product standard 7 Quali

43、ty assurance 7.1 Qualification 7.1.1 General requirements See EN 9133. 7.1.2 Qualification conditions The cables shall be submitted for qualification tests on drums, spools or in coils in sufficient lengths, wound evenly and uniformly. Each drum, spool or coil shall have a label containing informati

44、on given in 9.1, Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 9 prEN 4049-001 :2004 Qualified cables Nominal cross-section AWG a 0,4 22 7.1.3 Q

45、ualification tests See Table 2. Cables covered by the same qualification Nominal cross-section AWG a 0,6 20 7.1.4 Extension of qualification The qualification granted may be applicable to adjacent cross-sections in accordance with Table 4. 7.2 Acceptance tests 7.2.1 Required conditions See Table 2.

46、The acceptance tests shall be carried out on cables delivered against an order to check that the cable characteristics are maintained. 7.2.1.1 The cables which fail any of the test specified in 7.2.2 shall be rejected. Tests to be carried out on all cables 7.2.1.2 Random sampling tests: retest If an

47、y of the specimen fails one of the tests specified in 7.2.3, that test shall be repeated on another set of specimens of the same cross-section selected at random from the same batch. If one of these new specimen fails the test, the batch submitted for acceptance shall be rejected. 7.2.2 Production r

48、outine tests The tests shall be carried out on all cables delivered. See Table 2. 7.2.3 Tests prior to delivery They shall be carried out by sampling on each delivery batch. 7.2.4 Periodic tests They shall be carried out by sampling at least every three years. See Table 2. Copyright Association Euro

49、peene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 10 prEN 4049-001 :2004 8 Identification marking Unless otherwise specified, the type, cross-section and a reference for the identification of country of origin, manufacturer, and the year o