BS ISO 9211-4-2012 Optics and photonics Optical coatings Specific test methods《光学和光学仪器 光学涂层 专用试验方法》.pdf
《BS ISO 9211-4-2012 Optics and photonics Optical coatings Specific test methods《光学和光学仪器 光学涂层 专用试验方法》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 9211-4-2012 Optics and photonics Optical coatings Specific test methods《光学和光学仪器 光学涂层 专用试验方法》.pdf(24页珍藏版)》请在麦多课文档分享上搜索。
1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO 9211-4:2012 Optics and photonics Optical coatings Part 4: Specific test methodsBS ISO 9211-4:2012 BRITISH STANDARD National foreword This British Standard is the UK imp
2、lementation of ISO 9211-4:2012. It supersedes BS ISO 9211-4:2006 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee CPW/172, Optics and Photonics. A list of organizations represented on this committee can be obtained on request to its secretary. This pub
3、lication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012 ISBN 978 0 580 71407 8 ICS 37.020 Compliance with a British Standard cannot confer immun
4、ity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2012. Amendments issued since publication Date Text affectedBS ISO 9211-4:2012 ISO 2012 Optics and photonics Optical coatings Part 4: Specific test methods
5、Optique et photonique Traitements optiques Partie 4: Mthodes dessai spcifiques INTERNATIONAL STANDARD ISO 9211-4 Third edition Reference number ISO 9211-4:2012(E)BS ISO 9211-4:2012ISO 9211-4:2012(E) ii ISO 2012 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights reserved. Unless oth
6、erwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyrig
7、ht office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 9211-4:2012ISO 9211-4:2012(E) ISO 2012 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references 1 3 Terms and de
8、finitions . 1 4 Test conditioning 1 5 Abrasion resistance tests (conditioning method 01: abrasion) 1 5.1 General . 1 5.2 Test conditions 2 5.3 Degree of severity (conditioning method 01: abrasion) . 2 5.4 Recovery . 2 5.5 Evaluation 2 6 Adhesion tests (conditioning method 02: adhesion) . 3 6.1 Gener
9、al . 3 6.2 Test conditions 3 6.3 Degree of severity (conditioning method 02: adhesion) 3 6.4 Recovery . 3 6.5 Evaluation 3 7 Crosshatch test (conditioning method 03: crosshatch) . 4 7.1 General . 4 7.2 Test conditions 4 7.3 Conditioning 4 7.4 Recovery . 4 7.5 Evaluation 4 8 Solubility tests (conditi
10、oning method 04: solubility) 5 8.1 General . 5 8.2 Test conditions 5 8.3 Degree of severity (conditioning method 04: solubility) . 6 8.4 Recovery . 6 8.5 Evaluation 6 9 Environmental test code . 7 Annex A (normative) Materials for abrasion testing of optical coatings 8 Annex B (normative) Cheeseclot
11、h pad, pad cover and fixture preparation for moderate abrasion testing of optical coatings 11 Annex C (normative) Visual examination of optical coatings 13 Bibliography .14BS ISO 9211-4:2012ISO 9211-4:2012(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation
12、 of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.
13、International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance wit
14、h the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approv
15、al by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9211-4 was prepared by Technical Committ
16、ee ISO/TC 172, Optics and photonics, Subcommittee SC 3, Optical materials and components. This third edition cancels and replaces the second edition (ISO 9211-4:2006), which has been technically revised. ISO 9211 consists of the following parts, under the general title Optics and photonics Optical c
17、oatings: Part 1: Definitions Part 2: Optical properties Part 3: Environmental durability Part 4: Specific test methods iv ISO 2012 All rights reservedBS ISO 9211-4:2012INTERNATIONAL ST ANDARD ISO 9211-4:2012(E) Optics and photonics Optical coatings Part 4: Specific test methods 1 Scope ISO 9211 desc
18、ribes surface treatments of components and substrates, excluding ophthalmic optics (spectacles), by the application of optical coatings and gives a standard form for their specification. It defines the general characteristics and the test and measurement methods wherever necessary, but it is not int
19、ended to define the process method. This part of ISO 9211 describes specific test procedures for coating environmental durability tests that are identified in ISO 9211-3 but not described in other normative references. They are typically performed in sequence with other environmental durability test
20、s, as shown in ISO 9211-3:2008, Annex A. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the
21、 referenced document (including any amendments) applies. ISO 48, Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD). ISO 9211-1, Optics and photonics Optical coatings Part 1: Definitions ISO 29862, Self adhesive tapes Determination of peel adhesion
22、properties 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 9211-1 apply. 4 Test conditioning Before and after subjecting a coated specimen (component or witness sample) to any inspection or test, the specimen shall be thoroughly cleaned as required t
23、o remove dirt, finger marks, smears, etc. Recommended storage time is at least 12 h after the coating process under ambient atmospheric conditions, or as specified between manufacturer and buyer. 5 Abrasion resistance tests (conditioning method 01: abrasion) 5.1 General The purpose of these tests is
24、 to evaluate to what extent the optical and mechanical properties of optical coatings on components and substrates are affected when subjected to specific abrading conditions at ambient atmospheric conditions. ISO 2012 All rights reserved 1BS ISO 9211-4:2012ISO 9211-4:2012(E) 5.2 Test conditions 5.2
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO921142012OPTICSANDPHOTONICSOPTICALCOATINGSSPECIFICTESTMETHODS 光学 光学仪器 涂层 专用 试验 方法 PDF

链接地址:http://www.mydoc123.com/p-396011.html