BS ISO 9058-2008 Glass containers - Standard tolerances for bottles《玻璃容器 瓶用标准公差》.pdf

《BS ISO 9058-2008 Glass containers - Standard tolerances for bottles《玻璃容器 瓶用标准公差》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 9058-2008 Glass containers - Standard tolerances for bottles《玻璃容器 瓶用标准公差》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 9058:2008 Glass containers Standard tolerances for bottles ICS 55.100 BS ISO 9058:2008 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 May 2008 BSI 2008 ISBN 978 0 580 57617 1 National foreword This British Standard

2、 is the UK implementation of ISO 9058:2008. It supersedes BS ISO 9058:1992 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee PKW/0, Packaging, to Panel PKW/0/-/7, Glass. A list of organizations represented on this committee can be obtained on request to

3、 its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication Date CommentsIN

4、TERNATIONAL STANDARD ISO 9058 Second edition 2008-03-01 Reference number ISO 9058:2008(E) Glass containers Standard tolerances for bottles Rcipients en verre Tolrances standards pour bouteillesBS ISO 9058:2008ii iii Foreword ISO (the International Organization for Standardization) is a worldwide fed

5、eration of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that comm

6、ittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accorda

7、nce with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires

8、 approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9058 was prepared by Technical Co

9、mmittee ISO/TC 63, Glass containers. This second edition cancels and replaces the first edition (ISO 9058:1992), which has been technically revised. BS ISO 9058:2008 blank1 Glass containers Standard tolerances for bottles 1S c o p e This International Standard specifies tolerances for glass bottles

10、of circular cross-section and nominal capacity from to . NOTE This International Standard is based on CE.T.I.E Centre technique international de lembouteillage et du conditionnement (International Technical Centre for Bottling and Packaging), 112-114, rue La Botie, 75008 Paris, France, http:/www.cet

11、ie.org data sheet DT 2 (1996) and EC Council Directive 75/107/EEC. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu

12、ment (including any amendments) applies. ISO 7348:1992, Glass containers Manufacture Vocabulary ISO 9009:1991, Glass containers Height and non-parallelism of finish with reference to container base Test methods 3 Terms and definitions For the purposes of this document, the terms and definitions give

13、n in ISO 7348 and ISO 9009 and the following apply. 3.1 leading body diameter greatest horizontal cross-sectional dimension of a container 4 Tolerances 4.1 Capacity tolerance The actual capacity error (tolerance) shall be in accordance with the values specified in Table 1. Table 1 Capacity tolerance

14、s Nominal capacity, Maximum permissible error of the actual capacityof 3 3 6 2 10 1 50 ml 5 000 ml V n ml % V n ml 50V n 100 100V n 200 200V n 300 300V n 500 500V n 1 000 1 000V n 5 000 BS ISO 9058:20082 The maximum permissible error in the brimful capacity shall be the same as the maximum permissib

15、le error in the corresponding nominal capacity. 4.2 Nominal height tolerance, The nominal height tolerance, in millimetres, shall be calculated using the following formula: where is the nominal height, in millimetres. 4.3 Nominal leading diameter tolerance, The nominal leading body diameter toleranc

16、e, in millimetres, shall be calculated using the following formula: where is the nominal leading body diameter, in millimetres. 4.4 Verticality tolerance, (vertical axis deviation tolerance) The verticality tolerance, in millimetres, shall be calculated using the following formulae: a) for a nominal

17、 height : b) for a nominal height : where is in millimetres. 4.5 Tolerance on non-parallelism of finish with reference to container base The tolerance on non-parallelism of finish with reference to container base (or the slope of finish) shall be in accordance with the values specified in Table 2. T

18、able 2 Tolerance on non-parallelism of finish with reference to container base Dimensions in millimetres Nominal diameter of finish Tolerance 0,45and 0,6and 0,7and 0,8and 0,9 1 T H T H = (0,6 + 0,004H) H T D T D = (0,5 + 0,012D) D T V H 120 mm T V = 1,5 mm H120 mm T V = 0,3 + 0,01H H 20 20 30 30 40

19、40 50 50 60 60 BS ISO 9058:2008 blankBS ISO 9058:2008 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is inco

20、rporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if any

21、one finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating serv

22、ice called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-

23、. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide

24、 range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20

25、8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002.

26、Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications.

27、 BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopy

28、ing, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.