EN 6049-003-2018 Aerospace series - Electrical cables installation - Protection sleeve in meta-aramid fibres - Part 003 Braided tubular expandable - Product sta.pdf

《EN 6049-003-2018 Aerospace series - Electrical cables installation - Protection sleeve in meta-aramid fibres - Part 003 Braided tubular expandable - Product sta.pdf》由会员分享，可在线阅读，更多相关《EN 6049-003-2018 Aerospace series - Electrical cables installation - Protection sleeve in meta-aramid fibres - Part 003 Braided tubular expandable - Product sta.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Aerospace series - Electrical cables, installation - Protection sleeve in meta-aramid fibresPart 003: Braided, tubular, expandable - Product standardBS EN 6049-003:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM E

2、N 6049-003 August 2018 ICS 49.060 Supersedes EN 6049-003:2009English Version Aerospace series - Electrical cables, installation - Protection sleeve in meta-aramid fibres - Part 003: Braided, tubular, expandable - Product standard Srie arospatiale - Cbles lectriques, installation - Gaine de protectio

3、n en fibres mta-aramides - Partie 003: Tresse, tubulaire, expansible - Norme de produitLuft- und Raumfahrt - Elektrische Leitungen, Installation - Schutzschluche aus Meta-Aramidfasern -Teil 003: Geflecht, rhrenfrmig, dehnbar - Produktnorm This European Standard was approved by CEN on 18 January 2018

4、. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on

5、 application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENEL

6、EC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy

7、, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centr

8、e: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6049-003:2018 ENational forewordThis British Standard is the UK implementation of EN 6049003:2018. It supersedes BS EN 6049003:2009, whic

9、h is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include al

10、l the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 51519 4ICS 49.060Compliance with a British Standard cannot confer immunity from legal obligations. This British St

11、andard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 6049003:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6049-003 August 2018 ICS 49.060 Supersed

12、es EN 6049-003:2009English Version Aerospace series - Electrical cables, installation - Protection sleeve in meta-aramid fibres - Part 003: Braided, tubular, expandable - Product standard Srie arospatiale - Cbles lectriques, installation - Gaine de protection en fibres mta-aramides - Partie 003: Tre

13、sse, tubulaire, expansible - Norme de produitLuft- und Raumfahrt - Elektrische Leitungen, Installation - Schutzschluche aus Meta-Aramidfasern -Teil 003: Geflecht, rhrenfrmig, dehnbar - Produktnorm This European Standard was approved by CEN on 18 January 2018. CEN members are bound to comply with the

14、 CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management

15、 Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status a

16、s the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Ne

17、therlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2

18、018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6049-003:2018 EBS EN 6049003:2018EN 6049-003:2018 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Composition, dimensions

19、and mass . 4 5 Test methods 7 6 Designation . 9 7 Marking . 9 BS EN 6049003:2018EN 6049-003:2018 (E) 3 European foreword This document (EN 6049-003:2018) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried ou

20、t in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publ

21、ication of an identical text or by endorsement, at the latest by February 2019, and conflicting national standards shall be withdrawn at the latest by February 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be

22、 held responsible for identifying any or all such patent rights. This document supersedes EN 6049-003:2009. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cr

23、oatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tu

24、rkey and the United Kingdom. BS EN 6049003:2018EN 6049-003:2018 (E) 4 1 Scope This European Standard defines the characteristics of tubular braided expandable mechanical protection sleeves for electrical cable and cable bundles made from meta-aramid fibres and provided with a water repelled protecti

25、on. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (inclu

26、ding any amendments) applies. EN 2825, Aerospace series Burning behaviour of non metallic materials under the influence of radiating heat and flames Determination of smoke density EN 2826, Aerospace series Burning behaviour of non metallic materials under the influence of radiating heat and flames D

27、etermination of gas components in the smoke EN 3844-1, Aerospace series Flammability of non metallic materials Part 1: Small burner test, vertical Determination of the vertical flame propagation EN 6049-001, Aerospace series Electrical cables, installation Protection sleeve in meta-aramid fibres Par

28、t 001: Technical specification EN 6059-100, Aerospace series Electrical cables, installation Protection sleeves Test methods Part 100: General.1)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 6049-001 apply. ISO and IEC maintain terminological databa

29、ses for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp 4 Composition, dimensions and mass 4.1.1 Composition of the tows Each tow shall be built-up of several groups of mult

30、ifilament fibres made from Meta-aramid. The number of groups which forms a tow and the width of the tow depends on the braiding configuration (braiding Figure 1 and braiding angle) of the sleeve, see 4.1.2. The thickness of the tow shall be so that the finished sleeve meet the mechanical and environ

31、mental requirements. One length of sleeve shall be built-up of one type of tow. 1) All parts quoted in this document. BS EN 6049003:2018EN 6049-003:2018 (E) 5 4.1.2 Composition, dimensions and mass of the sleeve The composition of the sleeve (braiding Figure 1, braiding angle and tow width) shall be

32、 so that the sleeve meet the requirements for dimensions, coverage, expansion range and mass. The coverage shall be 80 % minimum. The braiding Figure 1 shall consist of two groups of tows in two directions. The braiding angle between the two groups shall be equal over the length of the sleeve. The m

33、aximum difference measured on a mandrel with the delivered diameter in accordance with EN 6059-202 is 3 %. Figure 2 and Table 2 give the composition and the dimensions of the sleeve. Braiding pattern Key 1 Pitch 2 One tow d = Inner diameter Figure 1 Composition of the sleeve BS EN 6049003:2018EN 604

34、9-003:2018 (E) 6 Table 1 Dimensions and mass Size code d Mass Delivered min. max. Nominal a max. b mm mm mm mm g/m 02 1 1 2 2 3 04 2 2 4 4 4 06 4 4 8 6 8,5 08 6 6 12 8 11,5 10 8 8 16 10 14 15 10 10 20 15 17,5 20 12 12 24 20 22 25 15 15 30 25 32,5 30 20 20 40 30 39,5 aIn practice approximately the ma

35、ximum diameter of a cable bundle. bAt the delivered diameter. 4.2 Color and materials 4.2.1 Color Color shall be olive green, code 5 (preferential), or ivory, code 9. Orange, code 3 (for FTI application); Red, code 2 (for arm system). 4.2.2 Materials The materials shall be multifilament fibres of me

36、ta-aramid and meet the requirements as specified in this standard. 4.3 Mechanical properties 4.3.1 Sun light exposure After testing according to EN 6059-301 for 40 hours, the retention of the tensile strength shall be 45 % minimum with respect to the determined values of non-tested tows. 4.3.2 Tempe

37、rature range The operation temperature of the protection sleeves shall be: a) Maximum: 240 C; b) Minimum: 55 C. NOTE Above 175 C: loss of water repellent properties. BS EN 6049003:2018EN 6049-003:2018 (E) 7 4.3.3 Resistance to fluids range After testing according to EN 6059-303, the retention of the

38、 tensile strength shall be 90 % minimum with respect to the determined values of non-tested tows. 4.3.4 Water absorption To fulfil the requirements for water absorption, the sleeve shall repel water as tested in EN 6059-305 for 6 hours. This test shall be executed after a high temperature exposure t

39、est according to EN 6059-302 at 175 C. 4.3.5 Mould growth After testing according to EN 6059-306, there shall no external deterioration which would affect service use and no mould growth visible to the naked eye. 4.3.6 Tensile strength of tows The tensile force to be applied per dTEX shall not be le

40、ss than 0,03 N. Degradation of the tensile strength after environmental tests shall be within the limits as mentioned in the relevant paragraph. For this test, unbraided tows of the batch which have been used for braiding of the sleeves may be used. 5 Test methods The tests shall be carried out as s

41、hown in Table 2. For the number of samples, see EN 6049-001. BS EN 6049003:2018EN 6049-003:2018 (E) 8 Table 2 Test methods and sanctions Test methods Title Remarks EN 6059-201 Visual inspection See 4.1 and 4.2.1. EN 6059-202 Dimensions and mass See 4.1.2. EN 6059-203 Coverage See 4.1.2. EN 6059-301

42、Sun light exposure See 4.3.1. EN 6059-302 High temperature exposure At maximum operating temperature (continue). See 4.3.2. EN 6059-303 Resistance to fluids See 4.3.3. EN 3844-1B Flammability After burn length (average) shall not exceed 203 mm (8 inches). After flame time (average) shall not exceed

43、15 s. After flame time drips (average) shall not exceed 5 s. EN 6059-304 Flammability EN 6059-305 Fluid absorption See 4.3.4. EN 6059-306 Mould growth See 4.3.5. EN 6059-401 Expansion range See 4.1.2. EN 6059-402 Bending properties Not applicable EN 6059-403 Scrape abrasion Needle load shall be 10 N

44、. EN 6059-404 Tensile strength See 4.3.6. EN 6059-405 Dynamic cut through Load shall be 30 N. EN 2825 B Smoke density The test duration shall be 4 min. The maximum specific optical smoke density (average) shall not exceed: Ds =200 (flaming mode) Ds =150 (non flaming mode) EN 2826 B Toxicity Gas comp

45、onent Limit of concentration (ppm) (Duration 4 min) Hydrogen fluoride HF 100 Hydrogen chloride HCI 150 Hydrogen cyanide HCN 150 Sulphur dioxide SO2/H2O 100 Nitrous gases NO/NO2 100 Carbon CO 1 000 BS EN 6049003:2018EN 6049-003:2018 (E) 9 6 Designation EXAMPLE Description block BRAIDED, TUBULAR, EXPA

46、NDABLE Identity block EN6049-003-02-5 Number of this standard Size code (see Table 1) Color code NOTE 1 If necessary, the code I9005 may be placed between the description block and the identity block. 7 Marking For the marking of the packaging, see EN 6049-001. BS EN 6049003:2018This page deliberate

47、ly left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Ins

48、titution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through ou

49、r open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and