ISO 3321-1975 Fluid power systems and components Cylinder bores and piston rod diameters Inch series《流体传动系统和元件 缸内径和活塞杆直径 英制系列》.pdf

《ISO 3321-1975 Fluid power systems and components Cylinder bores and piston rod diameters Inch series《流体传动系统和元件 缸内径和活塞杆直径 英制系列》.pdf》由会员分享，可在线阅读，更多相关《ISO 3321-1975 Fluid power systems and components Cylinder bores and piston rod diameters Inch series《流体传动系统和元件 缸内径和活塞杆直径 英制系列》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、ex* INTERNATIONAL STANDARD 3321 (i 4 aigIYHAPOfiHAR OPTAHM3AUMR IlO CTAHIlAPTW3AUWM.ORGANlSATlON INTERNATIONALE DE NORMALISATION Fluid power systems and components - Cylinder bores and piston rod diameters - Inch series Transmissions h ydrauliques et pneomatiques - Al Descriptors : hydraulic equipme

2、nt, pneumatic equipment, hydraulic cylinders, pneumatic cylinders, bores, piston-rods, dimensions, imperial R system. 8 Price based on 2 pages Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without

3、license from IHS-,-,-IS0 (the International Organization for Standardization) is a worldwide federation of national standards institutes (IS0 Member Bodies). The work of developing international Standards is carried out through IS0 Technical Committees. Every Member Body interested in a subject for

4、which a Technical Committee has been set up has the right to be represented on that Committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the Technical Committees are circulated to the Memb

5、er Bodies for approval before their acceptance as International Standards bv the IS0 Council. International Standard IS0 3321 was drawn up by Technical Committee lSO/TC 131, Fluid power systems and components, and circulated to the Member Bodies in December 1973, It has been approved by the Member B

6、odies of the following countries : Australia Germany Austria India Belgium Italy Brazil Japan Czechoslovakia New Zealand Finland South Africa, Rep. of Spain Switzerland Thailand United Kingdom U.S.A. Yugoslavia The Member Bodies of the following countries expressed disapproval of the document on tec

7、hnical grounds : Ireland Poland Sweden U.S.S.R. 0 international Organization for Standardization, 1975 l Printed in Switzerland Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IH

8、S-,-,-INTERNATIONAL STANDARD IS0 3321 -1975 (E) Fluid power systems and components - Cylinder bores and piston rod diameters - Inch series 0 INTRODUCTION In fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under pressure within an enclosed circuit. One compone

9、nt of such systems is the fluid power cylinder. This is a device which converts power into linear mechanical force and motion. It consists of a movable element, i.e. a piston and piston rod, operating within a cylindrical bore. This International Standard is one of two relating to fluid power cylind

10、er bores and piston rod diameters. The other, relating to a metric series, is IS0 3320, Fluid power systems and components - Cylinder bores and piston rod diameters - Metric series. For future design purposes the metric series is to be preferred to the inch series. 1 SCOPE AND FIELD OF APPLICATION T

11、his International Standard establishes an inch series of cylinder bores and piston rod diameters for application to hydraulic and pneumatic fluid power cylinders. 2 REFERENCE IS0 ., Fluid power - Vocabulary. l) 3 DEFINITIONS 3.1 cylinder : A device which converts fluid power into linear mechanical f

12、orce and motion. 3.2 cylinder bore : The internal diameter of the cylinder. 3.3 piston rod : The element transmitting mechanical force and motion from the piston. 3.4 For definitions of other terms used, see ISO. , , 1) In preparation. 1 Copyright International Organization for Standardization Provi

13、ded by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO3321-1975(E) 4 DIMENSIONS Refer to the figure for identification of bore and rod dimensions. Select cylinder bores and piston rod diameters from the dimensions shown in table 1 and

14、table 2. 5 IDENTIFICATION STATEMENT (Reference to this International Standard) Use the following statement in test reports, catalogues and sales literature when electing to comply with this International Standard : “Cylinder bores and piston rod diameters selected in accordance with IS0 3321, Fluid

15、power systems and components - Cylinder bores and piston rod diameters - Inch series. ” d, = cylinder bore; d, = piston rod diameter. FIGURE - Identification of bore and rod dimensions TABLE 1 - Cylinder bores Dimensions in inches *l 3/4 1 1 II8 1 I/2 2 2 II2 31f4 4 5 6 7 8 10 12 14 TABLE 2 -Piston rod diameters Dimensions in inches I- If4 5/I 6 318 112 5/E 1 1 3/8 1 3i4 2 2 II2 4 3 3 II2 4 4112 5 51/2 7 8112 10 Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-