ISO 17894-2005 Ships and marine technology - Computer applications - General principles for the development and use of programmable electronic systems in marine.pdf

《ISO 17894-2005 Ships and marine technology - Computer applications - General principles for the development and use of programmable electronic systems in marine.pdf》由会员分享，可在线阅读，更多相关《ISO 17894-2005 Ships and marine technology - Computer applications - General principles for the development and use of programmable electronic systems in marine.pdf（72页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 17894:2005(E) ISO 2005INTERNATIONAL STANDARD ISO 17894 First edition 2005-03-15 Ships and marine technology Computer applications General principles for the development and use of programmable electronic systems in marine applications Navires et technologies marines Application

2、s informatiques Principes gnraux pour le dveloppement et lutilisation des systmes lectroniques programmables pour applications marines ISO 17894:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but sha

3、ll not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area.

4、 Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by

5、ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electron

6、ic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org

7、Web www.iso.org Published in Switzerland ii ISO 2005 All rights reservedISO 17894:2005(E) ISO 2005 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope 1 2 Conformance . 1 3 Normative references . 1 4 Terms and definitions. 2 5 Symbols and abbreviated terms 5 6 Use of this Interna

8、tional Standard 5 7 Principles for marine PES 6 7.1 Intention for marine PES 6 7.2 Product principles for marine PES 6 7.2.1 First principle 6 7.2.2 Second principle . 6 7.2.3 Third principle . 7 7.2.4 Fourth principle. 7 7.2.5 Fifth principle 7 7.2.6 Sixth principle . 7 7.2.7 Seventh principle 8 7.

9、2.8 Eighth principle . 8 7.2.9 Ninth principle . 8 7.2.10 Tenth principle 8 7.2.11 Eleventh principle . 9 7.3 Life cycle principles for marine PES. 9 7.3.1 General. 9 7.3.2 Twelfth principle 9 7.3.3 Thirteenth principle. 9 7.3.4 Fourteenth principle . 10 7.3.5 Fifteenth principle . 10 7.3.6 Sixteent

10、h principle 11 7.3.7 Seventeenth principle. 11 7.3.8 Eighteenth principle 11 7.3.9 Nineteenth principle 11 7.3.10 Twentieth principle . 12 Annex A (informative) Terms and concepts used in this International Standard 13 Annex B (informative) Guidance on the principles for marine PES 18 Annex C (infor

11、mative) Guidance on the life cycle of marine PES . 39 Annex D (informative) Checklist for marine PES life cycle outputs 45 Annex E (informative) Application of the principles in the life cycle 57 Annex F (informative) Principles for marine PES 61 Bibliography . 63 ISO 17894:2005(E) iv ISO 2005 All r

12、ights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject

13、 for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC)

14、on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees

15、 are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be hel

16、d responsible for identifying any or all such patent rights. ISO 17894 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, Subcommittee SC 10, Computer applications. ISO 17894:2005(E) ISO 2005 All rights reserved vIntroduction Systems which include programmable electronic syst

17、ems (PES) are not exact substitutes for the electromechanical systems and/or crew tasks which they replace. A new technology is involved, which can provide opportunities for integration of traditional system components (including crew tasks) and more complex behaviour. This allows increases in effic

18、iency and safety through improved monitoring, better situational awareness on the bridge, etc. However, PES are complex products and, like all products, they can contain defects. These defects cannot be seen. Software does not respond to traditional engineering methods for the testing of soundness.

19、The combination of complexity, replacement of a combination of mechanical and crew functions with computer hardware and software, and industry practice in developing and maintaining marine PES leads to a wide range of potential defects which cannot be guarded against by prescriptive standards. The u

20、se of a PES in the management, monitoring or control of a ship may have several effects: potential to enhance the ability and efficiency of the crew; changes in the organization of work through the automation of lower-level tasks; integration of systems through use of several systems by one seafarer

21、; shift in the role of the crew towards the management of many linked, complex PES; shift of the crews perception of the ship to that presented by the interfaces of the PES; layers of embedded and/or application software interposed between the crew and the ship; physical interconnection of ship syst

22、ems through the use of computer networks. The overall effect of the use of PES is that the ship becomes one total system of inter-linked PES and crew which work together to fulfil the operators business goals for the ship. In order for this total system to be dependable, both the design of the PES a

23、nd the management of its use have to support the safe and effective performance of the crew as a critical component of the total system. Such a human-centred approach has to be based on a thorough knowledge of the particular skills, working environment and tasks of the crew using the PES. The total

24、system concept is described further in A.2. In the traditional approach to maritime safety, ship systems are built to and operated against precise, prescriptive standards. These standards were developed in response to feedback about incidents or risky behaviour of previous ship systems. This approac

25、h is appropriate for relatively simple systems in a time of slow technical innovation. However, suppliers and operators nowadays want to innovate with complex, new solutions. In addition, the base technologies for PES are evolving very quickly. The assurance of dependability in this case cannot rely

26、 on knowledge of previous systems. The solution is for the developer and operator to assess the risks from and to the particular ship, its systems, crew and its operating philosophy, and to address these specific risks in the design and operation of the PES. Components of the system can then either

27、be re- designed or operated in such a way as to minimize these risks. The quality of construction, operation and maintenance of the system to be sure of the achievement of a required level of dependability of the PES is also defined. This International Standard is based on best practice in PES devel

28、opment as stated in existing marine, electrical and electronic, IT, ergonomics and safety standards. It is not intended to replace any of these standards. It presents a synoptic view of the requirements of these standards as a framework of principles for the development of dependable PES. INTERNATIO

29、NAL STANDARD ISO 17894:2005(E) ISO 2005 All rights reserved 1Ships and marine technology Computer applications General principles for the development and use of programmable electronic systems in marine applications 1 Scope This International Standard provides a set of mandatory principles, recommen

30、ded criteria and associated guidance for the development and use of dependable marine programmable electronic systems for shipboard use. It applies to any shipboard equipment containing programmable elements which may affect the safe or efficient operation of the ship. It contains information for al

31、l parties involved in the specification, operation, maintenance and assessment of such systems. The principles and guidance in the document are largely based on requirements in national and International Standards. The source standards and their contribution to this International Standard are presen

32、ted in the bibliography. NOTE This International Standard does not directly address performance, test or test results requirements associated with specific types of equipment or functions. In such instances existing application or component standards may be applied, e.g. IEC 60945, in respect of nav

33、igation and radio-communications equipment. The responsible body (e.g. National Administration, Classification Society or other contracted party) will determine the applicability of this International Standard, and its specific requirements where any potential conflict arises. 2 Conformance An organ

34、ization demonstrating compliance to this International Standard shall provide evidence of how its system fulfils the principles stated in Clause 7. The evidence shall be to the satisfaction of an independent assessor. This can be achieved through compliance with the criteria given in Clause 7 or by

35、an alternative means which is to the satisfaction of an independent assessor. NOTE The criteria for assessment are given in an itemized list below each principle in Clause 7. 3 Normative references The following referenced documents are indispensable for the application of this document. For dated r

36、eferences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 9000:2000, Quality management systems Fundamentals and vocabulary ISO 9241-2, Ergonomic requirements for office work with visual display terminals

37、(VDTs) Part 2: Guidance on task requirements ISO 9241-10, Ergonomic requirements for office work with visual display terminals (VDTs) Part 10: Dialogue principles ISO 9241-11, Ergonomic requirements for office work with visual display terminals (VDTs) Part 11: Guidance on usability ISO 10007, Qualit

38、y management systems Guidelines for configuration management ISO 17894:2005(E) 2 ISO 2005 All rights reservedISO 13407, Human-centred design processes for interactive systems ISO/IEC 2382-1, Information technology Vocabulary Part 1: Fundamental terms ISO/IEC 9126-1, Software engineering Product qual

39、ity Part 1: Quality model ISO/IEC 12207, Information technology Software life cycle processes ISO/IEC 12207:1995/Amd.1:2002, Information technology Software life cycle processes Amendment 1 ISO/IEC 12207:1995/Amd.2:2004, Information technology Software life cycle processes Amendment 2 IEC 61069-1, I

40、ndustrial-process measurement and control Evaluation of system properties for the purpose of system assessment Part 1: General considerations and methodology IEC 61508-4, Functional safety of electrical/electronic/programmable electronic safety-related systems Part 4: Definitions and abbreviations I

41、EEE 610.12, Standard glossary of software engineering terminology BS 4778-3.1, Quality vocabulary. Availability, reliability and maintainability terms. Guide to concepts and related definitions BS 4778-3.2, Quality vocabulary. Availability, reliability and maintainability terms. Glossary of internat

42、ional terms 4 Terms and definitions For the purposes of this document, the following terms and definitions apply. The following referenced definitions are stated here since there is some inconsistency between the listed standards and also because the listed definitions are used frequently in this do

43、cument. Annex A elaborates the concepts behind key terms used in this International Standard. 4.1 context of use the users, goals, tasks, equipment (hardware, software and materials), and the physical and social environments in which a product is used ISO 9241-11 NOTE See A.2 for an elaboration of t

44、his term as used in this International Standard. 4.2 dangerous failure failure which has the potential to put the safety-related system into a hazardous or fail-to-function state IEC 61508-4 NOTE Whether or not the potential is realized may depend on the architecture of the system; in systems with m

45、ultiple channels to improve safety, a dangerous failure is less likely to lead to the overall dangerous or fail-to-function state. 4.3 dependability the extent to which a system can be relied upon to perform exclusively and correctly a task under given conditions at a given instant of time or over a

46、 given time interval, assuming that the required external resources are provided IEC 61096-5 ISO 17894:2005(E) ISO 2005 All rights reserved 34.4 failure the termination of the ability of an item to perform a required function IEC Guide 50(191) NOTE An error is that part of the system state which is

47、liable to lead to failure. A failure occurs because the system is erroneous IEC 61508-4. Error is a discrepancy between a computed, observed or measured value or condition and the true, specified, or theoretically correct value or condition. (IEC Guide 50(191); BS 4778) 4.5 fault the state of an ite

48、m characterized by inability to perform a required function, excluding the inability during preventive maintenance or other planned actions, or due to lack of external resources IEC Guide 50(191) 4.6 fault tolerance the attribute of an item that makes it able to perform a required function in the pr

49、esence of certain given sub- item faults IEC 61508-4, IEC Guide 50(191), BS 4778 4.7 hazard a situation that could occur during the lifetime of a product, system or plant that has the potential for human injury, damage to property, damage to the environment, or economic loss BS 4778 4.8 programmable electronic system a system based on one or more programmable electronic devices, connected to (and including) input devices (e.g. sensors) and/or output devices/final elements