ISO 16612-1-2005 Graphic technology - Variable printing data exchange - Part 1 Using PPML 2 1 and PDF 1 4 (PPML VDX-2005)《图形技术 可变打印数据交换 第1部分 利用PPML 2 1和PDF 1 4(.pdf

《ISO 16612-1-2005 Graphic technology - Variable printing data exchange - Part 1 Using PPML 2 1 and PDF 1 4 (PPML VDX-2005)《图形技术 可变打印数据交换 第1部分 利用PPML 2 1和PDF 1 4(.pdf》由会员分享，可在线阅读，更多相关《ISO 16612-1-2005 Graphic technology - Variable printing data exchange - Part 1 Using PPML 2 1 and PDF 1 4 (PPML VDX-2005)《图形技术 可变打印数据交换 第1部分 利用PPML 2 1和PDF 1 4(.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 16612-1:2005(E) ISO 2005INTERNATIONAL STANDARD ISO 16612-1 First edition 2005-12-15 Graphic technology Variable printing data exchange Part 1: Using PPML 2.1 and PDF 1.4 (PPML/VDX-2005) Technologie graphique change de donnes dimpression variables Partie 1: Utilisant PPML 2.1 et

2、 PDF 1.4 (PPML/VDX-2005) ISO 16612-1:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer perfo

3、rming the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PD

4、F file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central S

5、ecretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the

6、 address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reservedISO 16612-1:2005(E) ISO 2005 All rig

7、hts reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 2 4 Notations . 3 5 Conforming files, readers and writers 3 6 Technical requirements . 4 6.1 Data structure 4 6.2 Components of a PPML/VDX instance .5 6.3 PPML/VDX file naming 5

8、6.4 Structure of PPML/VDX files 5 6.5 Placement, orientation and interaction of compound elements 6 6.6 PDF data restrictions 6 6.7 PPML/VDX file identification 7 6.8 Embedding the PPMLVDX element in a PPML/VDX layout file 7 6.9 PPML layout data restrictions . 8 6.10 Specifying print product intent

9、specifications in the PPML/VDX layout file 11 6.11 Compression . 12 6.12 MD5 string encoding 12 6.13 Encryption . 12 Annex A (normative) The ContentBindingTable element definition . 13 Annex B (normative) Specifying print product intent in PPML . 17 Annex C (normative) The PPMLVDX element definition

10、 22 Annex D (informative) PPML/VDX notes 26 Annex E (informative) PPML feature summary . 29 Annex F (informative) Patents. 31 ISO 16612-1:2005(E) iv ISO 2005 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (I

11、SO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, gov

12、ernmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC

13、 Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the membe

14、r bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16612-1 was prepared by Technical Committee ISO/TC 130, Graphic technolo

15、gy. ISO 16612-1 is based on ANSI/CGATS.20-2002, Graphic technology Variable printing data exchange using PPML and PDF (PPML/VDX). ISO 16612 consists of the following parts, under the general title Graphic technology Variable printing data exchange: Part 1: Using PPML 2.1 and PDF 1.4 (PPML/VDX-2005)

16、ISO 16612-1:2005(E) ISO 2005 All rights reserved v Introduction ISO 16612 defines a data format and its usage for facillitating methods of exchange of digital data for variable data printing. It focuses on the exchange of files between establishments as well as within an integrated environment that

17、produces variable data printing. In particular, ISO 16612 is concerned with the exchange of content information as well as data representing the final appearance of customized or personalized print products to be manufactured. This part of ISO 16612 is based on the use of PPML version 2.1, PDF versi

18、on 1.4, and JDF version 1.2. Subsequent parts of ISO 16612 may use later revisions of these reference documents. However, because it will be important to be able to separately identify different versions of PPML/VDX, these will be created as individual parts of ISO 16612. This part of ISO 16612 is i

19、ntended to respond to the workflow requirements associated with the efficient and reliable exchange of final form data between one or more senders or receivers. The workflows addressed by this part of ISO 16612 can differ in their degree of optimization, flexibility and level of integration. It is r

20、ecognized that increasing flexibility can lead to the possibility of uncertainty or error in the interpretation of page appearance data as intended by the originator. Two conformance levels are identified that provide a reasonable balance between flexibility and predictability. Unlike conventional d

21、igital master formats that describe the final appearance of pages of a single document, a variable document format must define many related documents and the final graphical appearance of the pages of each document. Such documents are referred to in this part of ISO 16612 as “instance documents”. It

22、 is important to note that instance documents within a job may vary in page count, graphical content, page dimensions and finishing. The pages of instance documents are referred to in this part of ISO 16612 as “compound pages” where all pages of each document are defined in reader order. Each compou

23、nd page is an assembly of one or more partial pages or graphical content objects referred to in this part of ISO 16612 as “compound elements”. In most cases, many compound page definitions share a common set of compound element definitions. This part of ISO 16612 takes advantage of this content data

24、 sharing by allowing compound element data to be defined once regardless of the number of times it is referenced from the various compound page definitions. This effectively minimizes the overall size of the data that need to be exchanged, to a size that is manageable for most exchange scenarios. Th

25、e layout data entity that defines the instance documents and their compound pages is referred to in this part of ISO 16612 as the “layout data” of a PPML/VDX instance, where such a file set is referred to as a “PPML/VDX instance”. The layout data is defined using the Personalized Print Markup Langua

26、ge (PPML) data format, which is based on XML syntax. The PPML layout data can also carry meta-information that characterizes the re-use of specific renderings of compound element data as they appear as graphical marks on compound pages. This re-used information is intended to provide developers and

27、manufacturers of reader software, such as a PPML/VDX conforming print or display rendering system, with opportunities to improve the efficiency of page rasterization. All compound element data of a PPML/VDX instance referenced from the PPML layout data must be defined in the PDF format as defined in

28、 the Adobe PDF Reference, or as further restricted by the ISO 15930 family of International Standards (PDF/X). More specifically, the data that define a compound element as laid out on a compound page by the PPML data is a page of a PDF file. To clarify this concept further, the pages of one or more

29、 single or multiple page PDF files are used as the compound element data in a PPML/VDX instance. PPML/VDX enables the sender to identify the rigor with which the data being exchanged is defined and thus also identifies the areas in which the receiver is being asked to assume responsibility. This als

30、o enables the recipient of a file to clearly understand the liability assumed in accepting the file. This part of ISO 16612 does not have a provision for specifying data specific to a given reader process or printing device. Therefore, PPML/VDX has no provision for conveying device control informati

31、on such as imposition layout, trapping parameters, or any other device-specific information. ISO 16612-1:2005(E) vi ISO 2005 All rights reservedThis part of ISO 16612 does, however, allow data that describe print product intent to be included in a conforming PPML/VDX instance. “Print product intent”

32、 data, as they are referred to in this document, provide information that describes various characteristics of the finished, variable print products to be manufactured in a way that is device-independent. Characteristics such as binding style, media type and folding instructions are allowed to vary

33、per instance document and per compound page. The print product intent data of a PPML/VDX instance is defined by a restricted subset of the JDF Specification that is based on XML syntax. Two conformance levels are defined in this part of ISO 16612 and are referred to as PPML/VDX-Strict and PPML/VDX-R

34、elaxed. PPML/VDX-Strict provides the sender with maximum control and portability of the exchanged data and is the conformance level most suitable for blind complete exchange. All information necessary for defining a complete variable data job is included in the exchanged data. All content data must

35、be encoded as either PDF/X-1a and/or PDF/X-3 (see ISO 15930-1 and ISO 15930-3). PPML/VDX-Relaxed is used where not all information required by the receiver to manufacture the job is required to be included in the exchanged data. Data not provided in the exchange may be submitted separately, or ident

36、ified through communication between sender and receiver, and it will be the recipients responsibility to provide the additional data and properly bind them to the PPML/VDX data. This conformance level may also make use of PDF files not conforming to the PDF/X-1a or PDF/X-3 International Standards. T

37、he two conformance levels of PPML/VDX accommodate multiple exchange modes (including single file single transfer, multiple file single transfer and multiple file multiple transfer) while insuring reliable exchange of all data components. PPML/VDX is therefore suitable for collaborative authoring wor

38、kflows where more than one sender may exchange data components of the same job with a receiver, where the receiver can reliably determine when all components of the exchanged job are under their local control. A set of application notes for this part of ISO 16612 may be found at http:/www.npes.org/s

39、tandards/tools.html. In addition, pointers may be found on this site to development tools provided for the assistance of developers and users of applications prepared, based on this part of ISO 16612. It is anticipated that a variety of products will be developed around PPML/VDX, including readers,

40、writers and viewers of PPML/VDX files, as well as validation pre-flight tools and products that offer combinations of these features. Different products will incorporate various capabilities to prepare, interpret and process conforming files based on the application needs as perceived by the supplie

41、rs of the products. However, it is important to note that a conforming reader must be able to read and appropriately process all files conforming to a specified conformance level. INTERNATIONAL STANDARD ISO 16612-1:2005(E) ISO 2005 All rights reserved 1 Graphic technology Variable printing data exch

42、ange Part 1: Using PPML 2.1 and PDF 1.4 (PPML/VDX-2005) 1 Scope This part of ISO 16612 specifies the methods for the use of the Personalized Print Markup Language (PPML) and the Portable Document Format (PDF) for the exchange or identification of all elements necessary to render a variable data imag

43、ing job as intended by the sender. This part of ISO 16612 specifies document layout and content data and makes provision for product intent specifications using the Job Definition Format (e.g. paper selection, binding, finishing, etc.). This part of ISO 16612 is not directly intended to address appl

44、ications where printing is started before the file creation and transfer is complete (often called streaming applications). However, there are methods that allow it to be used for such applications. 2 Normative references The following referenced documents are indispensable for the application of th

45、is document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced (including any amendments) applies. ISO 15930-1:2001, Graphic technology Prepress digital data exchange Use of PDF Part 1: Complete exchange using CMYK data (PDF/X-1 and PD

46、F/X-1a) ISO 15930-3:2002, Graphic technology Prepress digital data exchange Use of PDF Part 3: Complete exchange suitable for colour-managed workflows (PDF/X-3) ISO 15930-4:2003, Graphic technology Prepress digital data exchange using PDF Part 4: Complete exchange of CMYK and spot colour printing da

47、ta using PDF 1.4 (PDF/X-1a) ISO 15930-6:2003, Graphic technology Prepress digital data exchange using PDF Part 6: Complete exchange of printing data suitable for colour-managed workflows using PDF 1.4 (PDF/X-3) Extensible Markup Language (XML) 1.0 (Second Edition), 6 October 2000, World Wide Web Con

48、sortium, Available from internet JDF Specification, Release 1.2, 2004, CIP4 Organization, Available from internet PDF Reference: Adobe Portable Document Format Version 1.4, third edition, 2001, Adobe Systems Incorporated (ISBN 0-201-75839-3) and its errata dated 2003/06/18, available from internet P

49、ersonalized Print Markup Language Functional Specification, version 2.1, Print On Demand Initiative, Dated July 31, 2002, available from internet RFC 1321: The MD5 Message-Digest Algorithm, April 1992, Ron Rivest, available from internet ISO 16612-1:2005(E) 2 ISO 2005 All rights reservedRFC 2396: Uniform Resource Identifiers (URI): Generic Syntax, 1995, Internet Engineering Task Force, available from internet 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 c