ISO 13584-501-2007 Industrial automation systems and integration - Parts library - Part 501 Reference dictionary for measuring instruments - Registration proced.pdf

《ISO 13584-501-2007 Industrial automation systems and integration - Parts library - Part 501 Reference dictionary for measuring instruments - Registration proced.pdf》由会员分享，可在线阅读，更多相关《ISO 13584-501-2007 Industrial automation systems and integration - Parts library - Part 501 Reference dictionary for measuring instruments - Registration proced.pdf（58页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 13584-501:2007(E) ISO 2007INTERNATIONAL STANDARD ISO 13584-501 First edition 2007-02-01 Industrial automation systems and integration Parts library Part 501: Reference dictionary for measuring instruments Registration procedure Systmes dautomatisation industrielle et intgration

2、 Bibliothque de composants Partie 501: Dictionnaire de rfrence pour les instruments de mesure Procdure denregistrement ISO 13584-501:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be ed

3、ited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a

4、trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member b

5、odies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechan

6、ical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.

7、org Published in Switzerland ii ISO 2007 All rights reserved ISO 13584-501:2007(E) Contents PageForeword vi 1 Scope . 1 2 Normative references. 3 3 Terms, definitions, and abbreviations 4 4 Representation of ontology concepts as dictionaries entries . 11 4.1 Measuring instrument classes 11 4.1.1 Mod

8、elled classes. 11 4.1.2 Referenced classes 12 4.1.3 Used attributes 12 4.2 Property DET definitions. 13 4.2.1 Modelled properties 13 4.2.2 Imported properties 13 4.2.3 Used Attributes . 13 4.3 Data type definitions 15 4.3.1 Modelled domains of values. 15 4.3.2 Used Attributes . 15 4.4 Identification

9、 of dictionary entries. 15 4.5 Specification of registration status. 16 5 Classification principles 17 5.1 Connection to pre-existing classification. 17 5.2 Upper level of the hierarchy. 17 5.2.1 Principal identification hierarchy . 17 5.2.2 Domain . 17 5.2.3 Function 17 5.2.4 Principle . 17 5.3 Sub

10、division of principal identification layers 18 5.4 Simplification of principal identification layers 18 5.5 Lower level of the hierarchy 18 5.6 Auxiliary classification 18 6 Computer sensible description. 19 ISO 2007 All rights reserved iii Introduction viiiISO 13584-501:2007(E) 6.1 External files 1

11、9 6.2 Information model and conformance class 19 6.3 Implementation method . 19 6.4 Language to be used for text attributes 19 6.5 Distribution of computer sensible descriptions 19 6.6 Control on the intermediate and formal releases 19 6.7 Registration authority identifier. 20 7 Registration and mai

12、ntenance procedure. 21 7.1 Structure of registration authority 21 7.2 Role and responsibility 23 7.2.1 Role and responsibility of parties. 23 7.2.2 Technical committee of registration authority 23 7.2.3 Secretary of registration authority 24 7.2.4 Validation committee of registration authority. 25 7

13、.2.5 ISO/IEC member body. 26 7.3 Registration procedure . 26 7.3.1 Decision rules. 26 7.3.2 Registration process flow . 27 7.3.3 Task of registration authority 30 8 Principles of dictionary edition, update, and maintenance 32 8.1 Initial release of the dictionary. 32 8.2 Version and revision numbers

14、 of dictionary elements . 32 8.2.1 Version number. 32 8.2.2 Revision number. 32 8.3 Identification of a formal release of the reference dictionary 33 Annex A (normative) Information object registration 34 Annex B (normative) Dictionary physical file. 35 Annex C (normative) Class definition 36 Annex

15、D (normative) Property definitions 37 Annex E (normative) Application form for dictionary elements. 38 Annex F (informative) History of registration authority. 44 ISO 2007 All rights reserved iv ISO 13584-501:2007(E) Bibliography 45 Index 47 Figures Figure 1 BSU coding style .16 Figure 2 Registratio

16、n time frame .28 Figure 3 Registration flow diagram .29 Tables Table 1 Structure of registration authority and levels of participation.22 Table F. 1 Historical record of ISO13584-501 registration authorities44 ISO 2007 All rights reserved v ISO 13584-501:2007(E) Foreword ISO (the International Organ

17、ization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been establish

18、ed has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

19、 International Standards are drafted in accordance with the rules given in the ISO/ IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. P

20、ublication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 13584 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all

21、such patent rights. ISO 13584-501 was prepared by Technical Committee ISO/TC 184, Industrial automation systems and integration, Subcommittee SC 4 Industrial data. ISO 13584 consists of the following parts under the general title Industrial automation systems and integration Parts library: Part 1: O

22、verview and fundamental principles; Part 20: Logical resource: Logical model of expressions; Part 24: Logical resource: Logical model of supplier library; Part 25: Logical resource: Logical model of supplier library with aggregate values and explicit content; Part 26: Logical resource: Information s

23、upplier identification; ISO 2007 All rights reserved vi ISO 13584-501:2007(E) Part 31: Implementation resources: Geometric programming interface; Part 42: Description methodology: Methodology for structuring part families; Part 101: View exchange protocol: Geometric view exchange protocol by paramet

24、ric program; Part 102: View exchange protocol by ISO 10303 conforming specification; Part 501: Reference dictionary for measuring instruments Registration procedure; Part 511: Mechanical systems and components for general use Reference dictionary for fasteners. The structure of the ISO 13584 series

25、is described in ISO 13584-1. The numbering of the parts of ISO 13584 reflects its structure: Parts 10 to 19 specify the conceptual descriptions; Parts 20 to 29 specify the logical resources; Parts 30 to 39 specify the implementation resources; Parts 40 to 49 specify the description methodology; Part

26、s 100 to 199 specify the view exchange protocol; Parts 500 to 599 specify the reference dictionaries. A complete list of parts of ISO 13584 is available from the Internet: http:/www.tc184-sc4.org/titles/PLIB_Titles.htm _ ISO 2007 All rights reserved vii ISO 13584-501:2007(E) Introduction ISO 13584 i

27、s an International Standard for the computer-interpretable representation and exchange of parts library data. The objective is to provide a neutral mechanism capable of transferring parts library data, independent of any application that is using a parts library data system. The nature of this descr

28、iption makes it suitable not only for the exchange of files containing parts, but also as a basis for implementing and sharing databases of parts library data. ISO 13584 is organized as a series of parts, each published separately. The parts of ISO 13584 fall into one of the following series: logica

29、l resources, implementation resources, description methodology, view exchange protocol and reference dictionaries. The series are described in ISO 13584-1. This part of ISO 13584 is a member of the reference dictionaries series. Parts of the standardized content series of parts specify ontologies fo

30、r representing the entities of an application domain, together with their descriptive properties and domains of values. Each entity, property or domain of values constitutes an entry of a dictionary and it is associated with a computer sensible and human readable definition, and with a computer sens

31、ible identification. The unique identification of a dictionary entry allows it to be referenced unambiguously from any application. Definitions and identifications of dictionary entries are represented as instances of the EXPRESS entity data types defined in the common dictionary schema, or in its e

32、xtensions defined in the logical series of parts of ISO 13584. This part of ISO 13584 specifies the requirements for an ISO-registered reference dictionary for representing measuring instruments with their properties and domains of values. This part of ISO 13584 also establishes and specifies the be

33、haviour of a registration authority whose role is to develop, maintain and update this ISO-registered reference dictionary for measuring instruments. These measuring instruments include environment measuring instruments and laboratory measuring instruments. ISO 2007 All rights reserved viiiINTERNATI

34、ONAL STANDARD ISO 13584-501:2007(E) Industrial automation systems and integration Parts library Part 501: Reference dictionary for measuring instruments Registration procedure 1 Scope This part of ISO 13584 specifies the requirements for an ISO-registered reference dictionary for measuring instrumen

35、ts with their descriptive properties and domains of values. The measuring instruments to be included in the dictionary comprise environment measuring instruments and laboratory measuring instruments. This part of ISO 13584 also specifies the procedures of an organization that develops, maintains and

36、 updates the reference dictionary for measuring instruments over a specified period of time. Such an organization is nominated by ISO and is referenced in this part of ISO 13584 as the registration authority of the reference dictionary for measuring instruments. The reference dictionary for measurin

37、g instruments contains the following: definitions and identifications of classes of measuring instruments, with associated classification scheme; definitions and identifications of data element types that represent properties of measuring instruments; definitions and identifications of domains of va

38、lues that prove useful for describing the above data element types. Each class, property or domain of values of this application domain constitutes an entry of the reference dictionary for measuring instruments defined by the registration authority. It is associated with a computer sensible and huma

39、n readable definition, and with a computer sensible identification. Each dictionary entry has an identifier that allows it to be referenced unambiguously from any application. Definitions and identifications of dictionary entries are defined by means of standard data that ISO 2007 All rights reserve

40、d 1 ISO 13584-501:2007(E) consist of instances of the EXPRESS entity data types defined in the common dictionary schema, and in its extensions defined in ISO 13584-24 and ISO 13584-25. The following are within the scope of this part of ISO 13584: requirements on the standard data that is used to rep

41、resent the various classes of measuring instruments, together with their descriptive properties and domains of values; NOTE 1 Descriptive properties can include properties concerning regulations on manufacturing, operation, maintenance, disposal and recycling of the product. the process to be follow

42、ed by the registration authority to propose and validate an initial version of the reference dictionary for measuring instruments; the process to be followed by the registration authority to collect, validate and register new entries or update entries for the reference dictionary for measuring instr

43、uments; the process to be followed by the registration authority to distribute the reference dictionary for measuring instruments. NOTE 2 The measuring instruments considered in this part of ISO 13584 include those measuring instruments that are classified in the classes ICS 13 (Environment. Health

44、protection. Safety), ICS 71.040 (Analytical chemistry) and ICS 17.220 (Electricity. Magnetism. Electrical and magnetic measurements). NOTE 3 The file format with which the standard data registered by the registration authority established by this part of ISO 13584 can be exchanged is specified in IS

45、O 10303-21. The following is outside the scope of this part of ISO 13584: the standard data themselves that constitute the content of the reference dictionary for measuring instruments. NOTE 4 The standard data themselves that constitute the content of the reference dictionary are registered by an I

46、SO registration authority, but are not ISO-standardized. NOTE 5 The standard data contain the definitions and properties of measuring instruments specified above, but they are not necessarily of measuring equipment.The difference in definitions between measuring equipment and measuring instruments i

47、s explained in IEC 60050-351. ISO 2007 All rights reserved 2 ISO 13584-501:2007(E) 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the cited edition applies. For undated references, the latest edition of the

48、 referenced document (including any amendments) applies. ISO 10303-21, Industrial automation systems and integration Product data representation and exchange Part 21: Implementation methods: Clear text encoding of the exchange structure. ISO 13584-1:2001, Industrial automation systems and integratio

49、n Parts library Part 1: Overview and fundamental principles. ISO 13584-24:2003, Industrial automation systems and integration Parts library Part 24: Logical resource: Logical model of supplier library. ISO 13584-25:2004, Industrial automation systems and integration Parts library Part 25: Logical resource: Logical model of supplier library with aggregate values and explicit content. ISO 13584-26:2000, Indu