ISO 10333-4-2002 Personal fall-arrest systems - Part 4 Vertical rails and vertical lifelines incorporating a sliding-type fall arrester《人员坠落救护系统 第4部分 垂直下落和滑动型下落.pdf

《ISO 10333-4-2002 Personal fall-arrest systems - Part 4 Vertical rails and vertical lifelines incorporating a sliding-type fall arrester《人员坠落救护系统 第4部分 垂直下落和滑动型下落.pdf》由会员分享，可在线阅读，更多相关《ISO 10333-4-2002 Personal fall-arrest systems - Part 4 Vertical rails and vertical lifelines incorporating a sliding-type fall arrester《人员坠落救护系统 第4部分 垂直下落和滑动型下落.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 10333-4:2002(E) ISO 2002INTERNATIONAL STANDARD ISO 10333-4 First edition 2002-04-01 Personal fall-arrest systems Part 4: Vertical rails and vertical lifelines incorporating a sliding-type fall arrester Systmes individuels darrt de chute Partie 4: Rails et cordes dassurance vert

2、icaux incorporant un dispositif darrt de type coulissant ISO 10333-4:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and

3、 installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software

4、 products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is fo

5、und, please inform the Central Secretariat at the address given below. ISO 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission i

6、n writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2002 All rights reserved ISO 103

7、33-4:2002(E) ISO 2002 All rights reserved iiiContents Page Foreword.iv Introduction.v 1 Scope 1 2 Normative references2 3 Terms and definitions .2 4 Requirements.7 5 Apparatus and test methods 12 6 Instructions for general use, marking and packaging.16 Annex A (normative) Dynamic performance testing

8、 .19 ISO 10333-4:2002(E) iv ISO 2002 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees

9、. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Intern

10、ational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Sta

11、ndards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 10333 may be

12、 the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10333-4 was prepared by Technical Committee ISO/TC 94, Personal safety Protective clothing and equipment, Subcommittee SC 4, Personal equipment for protection against falls. ISO 10333

13、consists of the following parts, under the general title Personal fall-arrest systems: Part 1: Full-body harnesses Part 2: Lanyards and energy absorbers Part 3: Self-retracting lifelines Part 4: Vertical rails and vertical lifelines incorporating a sliding-type fall arrester Part 5: Connectors with

14、self-closing and self-locking gates Systems performance tests will be the subject of a future part 6 to ISO 10333. Annex A forms a normative part of this part of ISO 10333. ISO 10333-4:2002(E) ISO 2002 All rights reserved vIntroduction In cases where the hazard of falling from a height exists and wh

15、ere, for technical reasons or for work of very short duration, safe access cannot be otherwise provided, it is necessary to consider the use of personal fall-arrest systems (PFAS). Such use should never be improvised and its adoption should be specifically provided for in the appropriate formal prov

16、isions for safety in the work place. PFAS complying with this part of ISO 10333 should satisfy ergonomic requirements and should only be used if the work allows means of connection to a suitable anchor device of demonstrated strength and if it can be implemented without compromising the safety of th

17、e user. Personnel should be trained and instructed in the safe use of the equipment and be observant of such training and instruction. This part of ISO 10333 is based on current knowledge and practice concerning the use of PFAS that incorporate a full-body harness as specified in ISO 10333-1. This p

18、art of ISO 10333 presumes that the manufacturer of the PFAS, subsystems or components will, for the sake of consistency and traceability, operate a quality management system which will comply with national and regional regulations in force at the time. Guidance on the form this quality management sy

19、stem may take can be found in ISO 9000, Quality management systems Fundamentals and vocabulary. INTERNATIONAL STANDARD ISO 10333-4:2002(E) ISO 2002 All rights reserved 1Personal fall-arrest systems Part 4: Vertical rails and vertical lifelines incorporating a sliding-type fall arrester 1 Scope This

20、part of ISO 10333 specifies requirements, test methods, instructions for use and maintenance, marking, labelling and packaging, as appropriate, for vertical rails and vertical lifelines which incorporate a sliding-type fall arrester. When connected to a full-body harness as specified in ISO 10333-1,

21、 vertical rails and vertical lifelines which incorporate a sliding-type fall arrester constitute a personal fall-arrest system (PFAS), which will be specified in a future International Standard. Vertical rails and vertical lifelines which incorporate a sliding-type fall arrester in accordance with t

22、his part of ISO 10333 are limited to use by a single person of total mass not exceeding 100 kg. NOTE 1 Users of PFAS whose total mass (which includes attached tools and equipment) exceeds 100 kg are advised to seek advice from the equipment manufacturers regarding the suitability of the equipment, w

23、hich may need additional testing. NOTE 2 PFAS using vertical rails and permanent vertical lifelines inherently limit the users horizontal movement, whereas PFAS using a temporary vertical lifeline permit significant horizontal movement by the user. Special notice should be given to the requirements

24、which accommodate this difference. The scope of this part of ISO 10333 does not extend to: a) inclined rails and lifelines, i.e. those which are installed at an angle between the true vertical and the lifeline or rail of more than 15 when viewed from the side elevation; b) the horizontally installed

25、 elements of compound rails or lifelines, i.e. those which have both vertically and horizontally installed elements linked by junctions. This part of ISO 10333 does not specify those additional requirements that would apply when PFAS are subjected to special conditions of use (where, for example, th

26、ere exist unusual limitations concerning access to the place of work and/or particular environmental factors). Thus treatments to ensure the durability of the materials of construction (such as heat treatment, anti-corrosion treatment, protection against physical and chemical hazards) are not specif

27、ied in this part of ISO 10333, but should comply with appropriate International Standards or, failing that, with national standards or other specifications dealing with relevant physical characteristics and/or the safety of users. ISO 10333-4:2002(E) 2 ISO 2002 All rights reserved 2 Normative refere

28、nces The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 10333. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part

29、 of ISO 10333 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid Internat

30、ional Standards. ISO 1140:1990, Ropes Polyamide Specification ISO 1141:1990, Ropes Polyester Specification ISO 9227:1990, Corrosion tests in artificial atmospheres Salt spray tests ISO 10333-1:2000, Personal fall-arrest systems Part 1: Full-body harnesses ISO 10333-5:2001, Personal fall-arrest syste

31、ms Part 5: Connectors with self-closing and self-locking gates ISO 14567:1999, Personal protective equipment for protection against falls from a height Single-point anchor devices EN 892:1996, Mountaineering equipment Dynamic mountaineering ropes Safety requirements and test methods EN 1891:1998, Pe

32、rsonal protective equipment for prevention of falls from a height Low stretch kernmantel ropes 3 Terms and definitions For the purposes of this part of ISO 10333, the following terms and definitions apply. 3.1 vertical rail rigid track which is permanently fastened by a number of brackets at interva

33、ls along its length to a fixed ladder or other structure, and to which a sliding-type fall arrester can be attached See Figure 1. NOTE The rail may consist of a number of sections held together by joining plates. 3.2 Vertical lifelines 3.2.1 vertical lifeline flexible line which is either permanentl

34、y or temporarily installed 3.2.2 permanent vertical lifeline tensioned line which is permanently fastened to at least one position at its upper end, to act as a reliable anchor point See Figure 2. NOTE 1 It is permanently fastened to a position at its lower extremity to a fixed ladder or other struc

35、ture, to which a sliding- type fall arrester can be attached. NOTE 2 The permanent vertical lifeline may additionally be attached to the fixed ladder or other structure at a number of locations at intervals along its length. ISO 10333-4:2002(E) ISO 2002 All rights reserved 33.2.3 temporary vertical

36、lifeline suspended line, which is temporarily fastened at its upper extremity to an overhead anchoring point, to which a sliding-type fall arrester can be attached See Figure 3. NOTE The temporary vertical lifeline may have a small weight fitted to the lower extremity to keep a nominal amount of ten

37、sion in the line. Key 1 Rung 5 Permanently installed ladder 2 Rail 6 Joint between rail sections 3 Intermediate fastening to rung 7 Sliding-type fall arrester 4 Connecting line Figure 1 Example of a vertical rail ISO 10333-4:2002(E) 4 ISO 2002 All rights reserved Key 1 Sliding-type fall arrester 6 L

38、ifeline 2 Permanently installed ladder 7 Connecting line 3 Upper fastening 8 Tensioning device 4 Vertical-lifeline energy absorber 9 Lower fastening 5 Intermediate fastening to rung Figure 2 Example of a permanent vertical lifeline ISO 10333-4:2002(E) ISO 2002 All rights reserved 5Key 1 Overhead anc

39、horing point 2 Lifeline 3 Sliding-type fall arrester 4 Connecting line 5 Tensioning mass Figure 3 Example of a temporary vertical lifeline 3.3 sliding-type fall arrester device which is designed to be attached to and to slide up and down the vertical rail or vertical lifeline in response to climbing

40、 movements, but locks automatically onto the vertical rail or vertical lifeline in response to the sudden motion of a fall 3.4 Connecting-line definitions 3.4.1 connecting line line, attached to the sliding-type fall arrester, which is designed to link the sliding-type fall arrester to a fall-arrest

41、 attachment point on the full-body harness NOTE The connecting line may be a lanyard, an energy absorber, a connector, or any combination of lanyard, energy absorber and connector. ISO 10333-4:2002(E) 6 ISO 2002 All rights reserved 3.4.2 connecting-line length shortest distance measured between the

42、bearing point of one connecting-line extremity to the other, with the connecting line held taut 3.4.3 lanyard finished length of flexible material which may be utilized as a part or the whole of the connecting line 3.4.4 connecting-line energy absorber component which may be utilized as a part or th

43、e whole of the connecting line, which is designed to dissipate the kinetic energy generated during a fall, and which limits the arresting forces exerted on the vertical rail or vertical lifeline and faller 3.4.5 connector component which may be utilized as a part or the whole of the connecting line,

44、 and which is used to link the connecting line to the fall-arrest attachment point on the full-body harness 3.5 anchor connector component which is used to connect a temporary vertical lifeline directly to an overhead anchoring point 3.6 vertical-lifeline energy absorber component which may or may n

45、ot be included at the upper fastening point of a permanent vertical lifeline, or at the overhead anchoring point of a temporary vertical lifeline, designed to dissipate the kinetic energy generated during a fall and limit the arresting forces exerted on the lifeline, upper fastening/anchoring point

46、and faller 3.7 opening point specially designed point on a vertical rail or permanent vertical lifeline, other than the extremities, where a sliding- type fall arrester may be attached or detached 3.8 opening device device on a sliding-type fall arrester which allows the arrester to be attached and

47、detached at any intermediate point on a vertical rail or vertical lifeline 3.9 post-fall arrest suspension state in which, after having being brought to a complete stop by a fall-arresting means, the faller remains suspended in the full-body harness 3.10 total mass sum of the users mass and all atta

48、ched clothing and equipment 3.11 minimum locking-test mass smallest mass, to the nearest whole kilogram, which, when attached to the raised free end of the connecting line and then released, will cause the fall arrester to lock on to the vertical rail or vertical lifeline and stay locked ISO 10333-4

49、:2002(E) ISO 2002 All rights reserved 73.12 General definitions 3.12.1 component constituent part of a PFAS or subsystem that has completed the manufacturers production cycle and is available for purchase 3.12.2 subsystem constituent part of a PFAS which may consist of one or more components, and is used to connect the user from the fall-arrest attachment element of the full-body harness to the anchor device NOTE A subsystem performs the two essential functions of a) connecting; b) fa