IEEE C37 35-1995 en Guide for the Application Installation Operation and Maintenance of High-Voltage Air Disconnecting and Load Interrupter Switches《高压空气断路和加载断路.pdf

《IEEE C37 35-1995 en Guide for the Application Installation Operation and Maintenance of High-Voltage Air Disconnecting and Load Interrupter Switches《高压空气断路和加载断路.pdf》由会员分享，可在线阅读，更多相关《IEEE C37 35-1995 en Guide for the Application Installation Operation and Maintenance of High-Voltage Air Disconnecting and Load Interrupter Switches《高压空气断路和加载断路.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、iIEEE Std C37.35-1995(Revision of IEEE Std C37.35-1976)IEEE Guide for the Application, Installation, Operation, and Maintenance of High-Voltage Air Disconnecting and Interrupter SwitchesSponsorSwitchgear Committeeof theIEEE Power Engineering SocietyApproved September 13, 1995IEEE Standards BoardAbst

2、ract: Guidance for users in the application, installation, operation, and maintenance of high-voltage airswitches and interrupter switches is provided.Keywords: high-voltage air switches, disconnecting switches, outdoor switches, interrupter switchesThe Institute of Electrical and Electronics Engine

3、ers, Inc.345 East 47th Street, New York, NY 10017-2394, USACopyright 1996 by the Institute of Electrical and Electronics Engineers, Inc.All rights reserved. Published 1996. Printed in the United States of America.ISBN 1-55937-597-3No part of this publication may be reproduced in any form, in an elec

4、tronic retrieval system or otherwise, without theprior written permission of the publisher.iiIEEE Standards documents are developed within the Technical Committees of the IEEE Societies and the StandardsCoordinating Committees of the IEEE Standards Board. Members of the committees serve voluntarily

5、and withoutcompensation. They are not necessarily members of the Institute. The standards developed within IEEE represent aconsensus of the broad expertise on the subject within the Institute as well as those activities outside of IEEE that haveexpressed an interest in participating in the developme

6、nt of the standard.Use of an IEEE Standard is wholly voluntary. The existence of an IEEE Standard does not imply that there are no otherways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEEStandard. Furthermore, the viewpoint expressed

7、 at the time a standard is approved and issued is subject to changebrought about through developments in the state of the art and comments received from users of the standard. EveryIEEE Standard is subjected to review at least every five years for revision or reaffirmation. When a document is moreth

8、an five years old and has not been reaffirmed, it is reasonable to conclude that its contents, although still of somevalue, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have thelatest edition of any IEEE Standard.Comments for revision of IEE

9、E Standards are welcome from any interested party, regardless of membership affiliationwith IEEE. Suggestions for changes in documents should be in the form of a proposed change of text, together withappropriate supporting comments.Interpretations: Occasionally questions may arise regarding the mean

10、ing of portions of standards as they relate tospecific applications. When the need for interpretations is brought to the attention of IEEE, the Institute will initiateaction to prepare appropriate responses. Since IEEE Standards represent a consensus of all concerned interests, it isimportant to ens

11、ure that any interpretation has also received the concurrence of a balance of interests. For this reasonIEEE and the members of its technical committees are not able to provide an instant response to interpretation requestsexcept in those cases where the matter has previously received formal conside

12、ration.Comments on standards and requests for interpretations should be addressed to:Secretary, IEEE Standards Board445 Hoes LaneP.O. Box 1331Piscataway, NJ 08855-1331USAAuthorization to photocopy portions of any individual standard for internal or personal use is granted by the Instituteof Electric

13、al and Electronics Engineers, Inc., provided that the appropriate fee is paid to Copyright Clearance Center.To arrange for payment of licensing fee, please contact Copyright Clearance Center, Customer Service, 222 RosewoodDrive, Danvers, MA 01923 USA; (508) 750-8400. Permission to photocopy portions

14、 of any individual standard foreducational classroom use can also be obtained through the Copyright Clearance Center.Note: Attention is called to the possibility that implementation of this standard may require use of subject mattercovered by patent rights. By publication of this standard, no positi

15、on is taken with respect to the existence orvalidity of any patent rights in connection therewith. The IEEE shall not be responsible for identifying all patentsfor which a license may be required by an IEEE standard or for conducting inquiries into the legal validity orscope of those patents that ar

16、e brought to its attention.iiiIntroduction(This introduction is not a part of IEEE Std C37.35-1995, IEEE Guide for the Application, Installation, Operation, and Maintenanceof High-Voltage Air Disconnecting and Interrupting Switches.)This publication is revised to recognize various construction and m

17、aintenance techniques. This document has alsobeen updated in accordance with certain local codes. It is one of a series of seven standards on high-voltage airswitches as follows:ANSI C37.32-1990, American National Standard Schedule of Preferred Ratings, Manufacturing Specifications, andApplication G

18、uide for High-Voltage Air Switches, Bus Supports, and Switch Accessories.IEEE Std C37.30-1992, IEEE Standard Definitions and Requirements for High-Voltage Air Switches (ANSI).IEEE Std C37.34-1994, IEEE Standard Test Code for High-Voltage Air Switches (ANSI).IEEE Std C37.36b-1990, IEEE Guide to Curre

19、nt Interruption with Horn-Gap Air Switches (ANSI) .IEEE Std C37.37-1979, (Reaff 1993), IEEE Standard Loading Guide for AC High-Voltage Air Switches (in excess of1000 volts) (ANSI).IEEE PC37.39 (P1247) (draft 11/5-95), Interrupter Switches for Alternating Current, Rated above 1000 Volts.1The Standard

20、s Committee on Power Switchgear, C37, which reviewed and approved this standard, had the followingpersonnel at the time of approval:E. Byron, Chair M. Calwise, Secretary A. K. McCabe (Executive Vice-Chair of High-Voltage Switchgear Standards)J. C. Scott (Executive Vice-Chair of Low-Voltage Switchgea

21、r Standards)D. L. Swindler (Executive Vice-Chair of IEC Activities)1This IEEE standards project was authorized but not approved by the IEEE Standards Board at the time this publication went to press. Forinformation about obtaining a draft, contact the IEEE.Organization Represented Name of Representa

22、tiveAssociation of Iron and Steel Engineers (vacant)Electric Light and Power Group M. C. MingoiaD. J. BorchartT. E. BruckJ. H. ProvanzanaJ. D. StewartG. R. Brandenberger (Alt.)A. K. McCabe (Alt.)Institute of Electrical and Electronics Engineers D. F. PeeloL. B. BeardH. L. BowlesivThe Working Group o

23、f the IEEE Switchgear Committee, which prepared this guide, consisted of the following personsat the time of IEEE Standards Board approval:Alexander Dixon, Chair C. J. AhranoJ. AngelisL. BennettH. L. BowlesR. A. BrownL. M. DunaginC. HandC. R. IsaacP. L. KolarikD. L. LottE. L. LuehringD. C. MillsA. C

24、. MonroeJ. C. W. RansomD. N. ReynoldsR. J. ReynoldsD. N. SharmiJ. WoodThe following persons were on the balloting committee:R. J. AltonRichard H. ArndtSteve AtkinsonL. R. BeardHarvey L. BowlesMatthew BrownJohn H. BrunkeRaymond L. CapraAlexander DixonP. W. DwyerA. MonroeD. SignonS. C. Atkinson (Alt.)

25、D. G. Kumbera (Alt.)L. V. McCall (Alt.)National Electrical Manufacturers Association R. GarzonW. KrachtH. L. MillerT. OlsonS. StoneE. Byron (Alt.)G. T. Jones (Alt.)G. Sakats (Alt.)D. L. Swindler (Alt.)Tennessee Valley Authority D. N. ReynoldsTesting Laboratory Group L. FrierP. NotarianU.S. Departmen

26、t of the Army, Office of the Chief of Engineers J. A. GilsonU.S. Department of the Interior, Bureau of Reclamation R. ArnoldU.S. Department of the Navy, Naval Construction Battalion Center R. L. ClarkWestern Area Power Administration G. D. BirneyOrganization Represented Name of RepresentativevJ. J.

27、DravisC. J. DvorakP. W. DwyerRuben D. GarzonLouis W. GaussaKeith I. GrayKenneth HendrixH. L. HessW. F. HoenigmannJerry M. JerabekP. L. KolarikDavid G. KumberaStephen R. LambertWard E. LaubachJohn G. LeachGeorge N. LesterDon LottE. L. LuehringP. C. MayoAndrew K. McCabeLawrence McCallMichael S. McGuir

28、eWilliam C. McKayHarvey W. MikuleckyDon C. MillsGeorges F. MontilletF. J. MuenchJames F. ODonnellRaymond P. OLearyA. F. ParksDavid F. PeeloG. O. PerkinsR. RanjanJ. C. W. RansomH. C. RossT. E. RoysterL. H. SchmidtE. W. SchmunkC. A. SchwalbeDevki N. SharmaGuy St. JeanD. L. SwindlerJohn S. TanneryS. H.

29、 TelanderFrederick C. TeufelThomas J. TobinEdward F. VeverkaCharles L. WagnerWhen the IEEE Standards Board approved this standard on September 13, 1995, it had the following membership:E. G. “Al“ Kiener, Chair Donald C. Loughry, Vice Chair Andrew G. Salem, Secretary Gilles A. BarilClyde R. CampJosep

30、h A. CannatelliStephen L. DiamondHarold E. EpsteinDonald C. FleckensteinJay Forster*Donald N. HeirmanRichard J. HollemanJim IsaakBen C. JohnsonSonny KasturiLorraine C. KevraIvor N. KnightJoseph L. Koepfinger*D. N. “Jim“ LogothetisL. Bruce McClungMarco W. MigliaroMary Lou PadgettJohn W. PopeArthur K.

31、 ReillyGary S. RobinsonIngo RuschChee Kiow TanLeonard L. TrippHoward L. Wolfman*Member EmeritusAlso included are the following nonvoting IEEE Standards Board liaisons:Satish K. AggarwalRichard B. EngelmanRobert E. HebnerChester C. TaylorRochelle L. SternIEEE Standards Project EditorviCLAUSE PAGE1. O

32、verview.91.1 Scope 91.2 General terminology 92. References.93. Definitions.104. Application104.1 Usual service conditions 104.2 Unusual service conditions 104.3 Other conditions. 104.4 Selection of insulation level. 105. Receipt and preparation 115.1 Handling. 115.2 Unpacking 115.3 Assembly and rigg

33、ing 116. Installation.126.1 Personnel safety during installation . 126.2 Instructions for assembly . 126.3 Alignment. 126.4 Rigidity. 126.5 Line conductors 126.6 Bus conductors. 126.7 Equipment connections 126.8 Ground connections . 126.9 Adjustments . 136.10 Cleaning equipment . 136.11 Inspection .

34、 136.12 Interrupter switches 137. Operation.137.1 Air switches 137.2 Interrupter switches 148. Maintenance 158.1 Disconnecting switches 158.2 Interrupter switches 15Annex A (Informative)Bibliography 179IEEE Guide for the Application, Installation, Operation, and Maintenance of High-Voltage Air Disco

35、nnecting and Interrupter Switches1. Overview1.1 ScopeThis guide presents suggestions on application, installation, operation, and maintenance as an aid to obtainingsatisfactory performance of indoor and outdoor high-voltage air disconnecting and interrupter switches rated in excessof 1000 Vac.It is

36、offered in recognition of the continuing need for general guidelines to supplement, but not replace, themanufacturers or users detailed instructions on installation, operation, and maintenance of disconnecting andinterrupter switches.1.2 General terminologyIn this guide, the term switches shall mean

37、 indoor and outdoor high-voltage air disconnecting switches, unlessqualified by other descriptive terms. The term interrupter switches shall mean indoor and outdoor high-voltageinterrupter switches, unless qualified by other descriptive terms.2. ReferencesThis guide shall be used in conjunction with

38、 the following standards. When the following standards are superseded byan approved revision, the revision shall apply.Accredited Standards Committee C2-1993, National Electrical Safety Code (NESC).11The NESC is available from the Institute of Electrical and Electronics Engineers, 445 Hoes Lane, P.O

39、. Box 1331, Piscataway, NJ 08855-1331,USA.10 Copyright 1998 IEEE All Rights ReservedIEEE Std C37.35-1995 IEEE GUIDE FOR THE APPLICATION, INSTALLATION, OPERATION, AND MAINTENANCEANSI C37.32-1990, Schedules of Preferred Ratings, Manufacturing Specifications, and Application Guide for High-Voltage Air

40、Switches, Bus Supports, and Switch Accessories.2IEEE Std C37.100-1992, Definitions for Power Switchgear (ANSI).3IEEE Std C37.30-1992, Requirements for High-Voltage Air Switches (ANSI). IEEE Std C37.36b-1990 IEEE Guide to Current Interruption with Horn-Gap Air Switches (ANSI). OSHA Rule 1910.269-1994

41、, Electric Power Generation, Transmission, and Distribution: Electrical ProtectiveEquipment.43. DefinitionsThe definitions of the terms used in this document are found in IEEE Std C37.100-1992.4. Application4.1 Usual service conditionsUsual service conditions for switches are defined in 2.1 of IEEE

42、Std C37.30-1992. These conditions specify limits inaltitude and in ambient air temperature.4.2 Unusual service conditionsUnusual service conditions are listed in 2.2 of IEEE Std C37.30-1992. Table 1 of IEEE Std C37.30-1992 lists altitudecorrection factors for rated withstand voltages, rated continuo

43、us currents, and ambient air temperatures for altitudesabove 3300 ft (1000 m).4.3 Other conditionsOther conditions affecting the application of switches are listed in IEEE Std C37.30-1992. For these and otherconditions, the switch manufacturer should be consulted.4.4 Selection of insulation levelThe

44、 selection of the insulation level for air switches on systems of various nominal voltages is a function of the degreeof surge protection, the insulation level of associated equipment such as circuit breakers and transformers, and thedegree of airborne contamination anticipated. Since insulators may

45、 have different levels of creepage distance for agiven lightning impulse withstand voltage, the creepage distance should be selected separately to provide adequate2ANSI publications are available from the Sales Department, American National Standards Institute, 11 West 42nd Street, 13th Floor, New Y

46、ork,NY 10036, USA.3IEEE publications are available from the Institute of Electrical and Electronics Engineers, 445 Hoes Lane, P.O. Box 1331, Piscataway, NJ 08855-1331, USA.4OSHA publications are available from the OSHA Publications Office, U.S. Department of Labor, 200 Constitution Avenue, N.W., Roo

47、m N3I0I,Washington DC 20210.Copyright 1998 IEEE All Rights Reserved 11OF HIGH-VOLTAGE AIR DISCONNECTING AND INTERRUPTER SWITCHES IEEE Std C37.35-1995service under expected atmospheric contamination conditions. In the bibliography in annex A, B3 5providesguidelines for selecting creepage distance.Swi

48、tches should be selected on the basis of both rated maximum voltage and lightning impulse withstand voltage. Thepreferred rated maximum voltages (given in kilovolts, rms) for switches and bus supports, and their correspondingpower frequency withstand ratings and lightning impulse withstand ratings,

49、are given in tables 1 and 6 of ANSIC37.32-1990. ANSI C37.32-1990 requires that the open-gap withstand be at least 110% of rated withstand to ground, and that thephase-to-ground withstand be at least 100% of the rated withstand to ground. There is no upper limit placed onwithstand voltages, which means it is possible that the phase-to-ground withstand could be higher than the open-gapwithstand.If a switch is overinsulated, that is, if the withstand capability of the switch insulation to ground is higher than thewithstand capability of the switch open gap, rod gaps or surge pro