IEEE 535-2013 en Qualification of Class 1E Vented Lead Acid Storage Batteries for Nuclear Power Generating Stations《核电站用1E级铅酸蓄电池组的合格鉴定》.pdf

《IEEE 535-2013 en Qualification of Class 1E Vented Lead Acid Storage Batteries for Nuclear Power Generating Stations《核电站用1E级铅酸蓄电池组的合格鉴定》.pdf》由会员分享，可在线阅读，更多相关《IEEE 535-2013 en Qualification of Class 1E Vented Lead Acid Storage Batteries for Nuclear Power Generating Stations《核电站用1E级铅酸蓄电池组的合格鉴定》.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、 IEEE Standard for Qualification of Class 1E Vented Lead Acid Storage Batteries for Nuclear Power Generating Stations Sponsored by the Stationary Batteries Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Power and Energy Society IEEE Std 535-2013 (Revision of IEEE Std 535-2006) IEEE St

2、d 535-2013 (Revision of IEEE Std 535-2006) IEEE Standard for Qualification of Class 1E Vented Lead Acid Storage Batteries for Nuclear Power Generating Stations Sponsor Stationary Batteries Committee of the IEEE Power and Energy Society Approved 31 October 2013 IEEE-SA Standards Board Abstract: Quali

3、fication methods for Class 1E vented lead acid batteries and racks to be used in nuclear power generating stations outside primary containment are described in this standard. Qualifications required by IEEE Std 308 can be demonstrated by using the procedures in this standard in accordance with IEEE

4、Std 323. The application of batteries in nuclear power generating stations can be divided into two sections: duty cycles equal to or less than 8 h and duty cycles greater than 8 h. A process to demonstrate qualifications for both applications is provided in this standard. Keywords: acceptance test,

5、battery capacity, battery maintenance, battery replacement criteria, electrolyte level, equalize charge, float voltage, IEEE 450, IEEE 535, performance test, specific gravity, test-discharge rate, vented lead-acid battery The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New

6、 York, NY 10016-5997, USA Copyright 2013 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 22 November 2013. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and

7、quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of

8、 an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought ab

9、out through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any du

10、ty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the ap

11、propriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CA

12、USED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESE

13、EABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral,

14、 that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars

15、, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are w

16、elcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate

17、 supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees a

18、re not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to joi

19、n the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with

20、the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge act

21、ion that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both publi

22、c and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does

23、not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arr

24、ange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance

25、Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document a

26、t any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reas

27、onable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether

28、it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more information about the IEEE SA or IEEEs standards development process, visit the IEEE-SA W

29、ebsite at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possi

30、bility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has

31、 filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights w

32、ithout compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not respons

33、ible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any l

34、icensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standar

35、ds Association. Copyright 2013 IEEE. All rights reserved. This is an unapproved IEEE Standards Draft, subject to change. vi Participants At the time this IEEE standard was completed, the Nuclear Battery Qualification Working Group had the following membership: Robert Beavers, Chair Jose Marerro, Vic

36、e Chair Tania Martinez-Navedo, Secretary Phyllis Archer Arc hie Bell Duane Brock Thomas Carpenter Larry Carson Steve Clark Hollen Crim Robert Fletcher Kyle Floyd John Gagge Jr. Wayne Johnson Jeffrey Lamarca Larry Meisner Lily Ramadan Jan Reber Prem Sahey Surrendra Salgia Robert Schmidt Chris Searles

37、 Al Williamson The following members of the individual balloting committee voted on this standard. Balloters may have voted for approval, disapproval, or abstention. Satish Aggarwal Ali Al Awazi Edward Amato Phyllis Archer Curtis Ashton Gary Balash Robert Beavers Thomas Brewington Daniel Brosnan Ken

38、t Brown Gustavo Brunello Nissen Burstein William Cantor Paul Cardinal Thomas Carpenter Larry Carson Leonard Casella Garry Chapman Troy Chatwin Mark Clark Mark Crisler Matthew Davis Ray Davis Peter Demar John Disosway Neal Dowling Wells Fargo Charles Finin Stephen Fleger Robert Fletcher Kyle Floyd Ro

39、bert Francis John Gagge Jr David Gilmer Randall Groves Ajit Gwal Aaron Hatok Hamidreza Heidarisafa Werner Hoelzl David Horvath David Ittner Wayne Johnson J Koepfinger Jim Kulchisky Chung-Yiu Lam Jeffrey LaMarca Michael Lauxman Greg Luri Jose Marrero Michael May John Mcalhaney Jr James Mcdowall Larry

40、 Meisner John Merando Kimberly Mosley Haissam Nasrat Dennis Neitzel Michael S. Newman Charles Ngethe Gary Nissen Lorraine Padden Mirko Palazzo James Parello Bansi Patel Jan Pirrong John Polenz Michael Roberts Prem Sahay Surendra Salgia Bartien Sayogo Glen Schinzel Robert Schmitt Christo Searles Sure

41、sh Shrimavle Gil Shultz David Smith Gary Stoedter Richard Tressler Lesley Varga Gerald Vaughn Stephen Vechy John Vergis Kenneth White Copyright 2013 IEEE. All rights reserved. This is an unapproved IEEE Standards Draft, subject to change. vii When the IEEE-SA Standards Board approved this standard o

42、n 31 October 2013, it had the following membership: John Kulick, Chair David J. Law, Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Masayuki Ariyoshi Peter Balma Farooq Bari Ted Burse Wael William Diab Stephen Dukes Jean-Philippe Faure Alexander Gelman Mark Halpin Gary

43、Hoffman Paul Houz Jim Hughes Michael Janezic Joseph L. Koepfinger* Oleg Logvinov Ron Petersen Gary Robinson Jon Walter Rosdahl Adrian Stephens Peter Sutherland Yatin Trivedi Phil Winston Yu Yuan *Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board liaisons: Richard DeBl

44、asio, DOE Representative Michael Janezic, NIST Representative Patrick Gibbons IEEE Standards Program Manager, Document Development Malia Zaman IEEE Standards Program Manager, Technical Program Development Copyright 2013 IEEE. All rights reserved. viii Introduction This introduction is not part of IE

45、EE Std 535-2013, IEEE Standard for Qualification of Class 1E Vented Lead Acid Storage Batteries for Nuclear Power Generating Stations. IEEE Std 323, IEEE Standard for Qualifying Class 1E Equipment for Nuclear Power Generating Stations, was developed to provide guidance for demonstrating and document

46、ing the adequacy of electrical equipment used in all Class 1E and interface systems. This standard, IEEE Std 535, was developed to provide specific methods and type-test procedures for lead storage batteries in adherence to IEEE Std 323. IEEE Std 344 methodology for seismic qualification is included

47、 for testing cells with and without battery racks. In general, IEEE Std 323 describes the qualification of equipment as requiring aging and irradiation exposure, followed by seismic testing. The qualification effort required in IEEE Std 323 may be reduced if the equipment is in a mild environment. H

48、owever, since vented lead acid battery cells have a significant aging mechanism in mild environments, aging is required prior to seismic testing. IEEE Std 535 was developed to provide a specific common process for qualification of vented lead acid cells that could be used by battery manufacturers. I

49、EEE Std 535-1979 was the initial issue of the standard. IEEE Std 535-1986 revised the standard to limit the plate designs to lead calcium-pasted (Faur) and lead antimony-pasted (Faur). IEEE Std 535-2006 was a general revision of IEEE Std 535-1986. This revision updates the standard to address the changes in nuclear plant design and the corresponding impact on battery cells. When IEEE Std 535 was first published, the typical duty cycle was 8 h or less. There was significant utility and telecommunications industry experience to back up the 8-h duty cycle. This revision