IEEE 1505 3-2015 en The Universal Test Interface Framework and Pin Configuration for Portable Benchtop Test Requirements Utilizing IEEE 1505 Receiver Fixture In.pdf

《IEEE 1505 3-2015 en The Universal Test Interface Framework and Pin Configuration for Portable Benchtop Test Requirements Utilizing IEEE 1505 Receiver Fixture In.pdf》由会员分享，可在线阅读，更多相关《IEEE 1505 3-2015 en The Universal Test Interface Framework and Pin Configuration for Portable Benchtop Test Requirements Utilizing IEEE 1505 Receiver Fixture In.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、IEEE Std 1505.3-2015 i IEEE Standard for the Universal Test Interface Framework and Pin Configuration for Portable/Benchtop Test Requirements Utilizing IEEE 1505 Receiver Fixture Interface Standard Sponsor IEEE Standards Coordinating Committee 20 on Test and Diagnosis for Electronic Systems Approved

2、 3 September 2015 IEEE-SA Standards Board ii Abstract: Portable/benchtop test equipment applications are supported in this document by defining a mass interconnection scheme and pin configuration based upon IEEE Std 1505-2010 and IEEE Std 1505.1-2008. Particular emphasis has been placed on defining

3、a more specific set of performance requirements than is defined by IEEE Std 1505-2010 and IEEE Std 1505.1-2008. These performance requirements are in the areas of the pin configuration, specific connector modules, and respective contacts. Keywords: ATE, ATS, fixture, IEEE 1505.3, interface, receiver

4、, scalable, TPS, UUT The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2016 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 20 January 2016. Printed in the United States of America. IEEE is

5、a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are sup

6、plied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the

7、 viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or o

8、ther services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given c

9、ircumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF

10、 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD,

11、EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE

12、should be considered the approved IEEE standard. iv Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not

13、be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the f

14、ormal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions f

15、or changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of inte

16、rests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation

17、requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations U

18、sers of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the appli

19、cable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and internati

20、onal copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By maki

21、ng these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individu

22、al standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any in

23、dividual standard for educational classroom use can also be obtained through the Copyright Clearance Center. v Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended f

24、rom time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten

25、 years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition o

26、f any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previou

27、sly. For more information about the IEEE SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. U

28、sers are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existen

29、ce or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assur

30、ance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential

31、 Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing t

32、erms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such

33、rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. vi Copyright 2016 IEEE. All rights reserved. Participants At the time this IEEE standard was completed, the Hardware Interfaces Working Group had the following membership: Stephen M

34、ann, Chair Robert Spinner, Vice Chair W. Larry Adams Jr. Chris Boggs Malcom Brown David Droste William Frank Chris Geiger George Isabella Nathan Hinks Chuck Kolfeldt James Langlois Tom Leddy Adam Ley Scott Misha Ted Ronnenburg Mike Seavey Bill Sartor Richard Spears John Stabler Michael Stora The fol

35、lowing members of the individual balloting committee voted on this standard. Balloters may have voted for approval, disapproval, or abstention. W. Larry Adams Jr. Bill Brown Malcom Brown Keith Chow David Droste Heiko Ehrenberg William Frank Chris Gorringe Randall Groves Werner Hoelzl James Langlois

36、Adam Ley Stephen Mann Michael Newman Leslie Orlidge Ulrich Pohl Mike Seavey Roger Sowada Robert Spinner Joseph Stanco Michael Stora Walter Struppler When the IEEE-SA Standards Board approved this standard on 3 September 2015, it had the following membership: John D. Kulick, Chair Jon Walter Rosdahl,

37、 Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Masayuki Ariyoshi Ted Burse Stephen Dukes Jean-Philippe Faure J. Travis Griffith Gary Hoffman Michael Janezic Joseph L. Koepfinger* David J. Law Hung Ling Andrew Myles T. W. Olsen Glenn Parsons Ronald C. Petersen Annette D

38、. Reilly Stephen J. Shellhamer Adrian P. Stephens Yatin Trivedi Phillip Winston Don Wright Yu Yuan Daidi Zhong *Member Emeritus vii Copyright 2016 IEEE. All rights reserved. Introduction This introduction is not part of IEEE Std 1505.3-2015, IEEE Standard for the Universal Test Interface Framework a

39、nd Pin Configuration for Portable/Benchtop Test Requirements Utilizing IEEE 1505 Receiver Fixture Interface Standard. Developers, users, and buyers of benchtop and general purpose portable test equipment can benefit from having a standardized mechanical interface and electrical signal input/output (

40、I/O) pin configuration. Implementing a standard interface and pin configuration will permit testing interoperability with other benchtop and portable test equipment that has implemented the same standards. This standard provides the definition of both the mechanical interface and the pin configurati

41、on. viii Copyright 2016 IEEE. All rights reserved. Contents 1. Overview 1 1.1 General 1 1.2 Scope . 1 1.3 Purpose 2 1.4 Application 2 1.5 Conventions used within this document 2 2. Normative references 3 3. Definitions, acronyms, and abbreviations 4 3.1 Definitions . 4 3.2 Acronyms and abbreviations

42、 . 4 4. Framework, connector and contact pin configuration 5 4.1 Architecture overview . 5 4.2 Framework specifications 7 4.3 Pin configuration specification 11 4.4 Connector/contact pin configuration specifications . 12 4.5 Contact specifications 12 5. Compliance specification . 16 5.1 Levels of co

43、mpliance . 16 6. Environmental/quality specifications . 17 Annex A (informative) Bibliography . 18 1 Copyright 2016 IEEE. All rights reserved. IEEE Standard for the Universal Test Interface Framework and Pin Configuration for Portable/Benchtop Test Requirements Utilizing IEEE 1505 Receiver Fixture I

44、nterface Standard IMPORTANT NOTICE: IEEE Standards documents are not intended to ensure safety, security, health, or environmental protection, or ensure against interference with or from other devices or networks. Implementers of IEEE Standards documents are responsible for determining and complying

45、 with all appropriate safety, security, environmental, health, and interference protection practices and all applicable laws and regulations. This IEEE document is made available for use subject to important notices and legal disclaimers. These notices and disclaimers appear in all publications cont

46、aining this document and may be found under the heading “Important Notice” or “Important Notices and Disclaimers Concerning IEEE Documents.” They can also be obtained on request from IEEE or viewed at http:/standards.ieee.org/IPR/disclaimers.html. 1. Overview 1.1 General The IEEE Std 1505 family of

47、Standards allows test systems and test system fixtures to be designed, developed, and deployed; the fixtures could then be exchanged with other test systems adhering to the common format of the IEEE Std 1505 family of Standards. The IEEE Std 1505 family of Standards has been developed and are mainta

48、ined under the guidance of the Hardware Interfaces (HI) Subcommittee of IEEE Standards Coordinating Committee 20 (SCC20). 1.2 Scope The scope of this standard is the definition of a universal framework/footprint and pin configuration utilizing IEEE 1505 receiver-fixture interface (RFI) framework and connector specifications for portable and benchtop test applications. The pin configuration defined within this standard shall apply to commercial, aerospace, and military automatic test equipment (ATE) testing applications.