IEC 61747-10-2-2014 Liquid crystal display devices - Part 10-2 Environmental endurance and mechanical test methods - Environmental and endurance《液晶显示装置 第10-2部分 环境 耐受性和机械试验方法 环境和耐受性》.pdf

《IEC 61747-10-2-2014 Liquid crystal display devices - Part 10-2 Environmental endurance and mechanical test methods - Environmental and endurance《液晶显示装置 第10-2部分 环境 耐受性和机械试验方法 环境和耐受性》.pdf》由会员分享，可在线阅读，更多相关《IEC 61747-10-2-2014 Liquid crystal display devices - Part 10-2 Environmental endurance and mechanical test methods - Environmental and endurance《液晶显示装置 第10-2部分 环境 耐受性和机械试验方法 环境和耐受性》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61747-10-2 Edition 1.0 2014-09 INTERNATIONAL STANDARD Liquid crystal display devices Part 10-2: Environmental, endurance and mechanical test methods Environmental and endurance IEC 61747-10-2:2014-09(en) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2014 IEC, Geneva, Switzerland All rights

2、reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester

3、. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 0

4、3 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The techni

5、cal content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical informa

6、tion on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, te

7、xt, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email

8、. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 14 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) o

9、nline. IEC Glossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC

10、Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 61747-10-2 Edition 1.0 2014-09 INTERNATIONAL STANDARD Liquid crystal display devices Part 10-2: Environmental,

11、 endurance and mechanical test methods Environmental and endurance INTERNATIONAL ELECTROTECHNICAL COMMISSION Q ICS 31.120 PRICE CODE ISBN 978-2-8322-1846-4 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized d

12、istributor. 2 IEC 61747-10-2:2014 IEC 2014 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Terms, definitions and symbols 6 4 Standard atmospheric conditions for measurements and tests: 6 5 Test methods . 6 5.1 General . 6 5.2 Rapid change of temperature: two-chamber method . 6 5.3 Specif

13、ied change rate of temperature: one-chamber method . 8 5.4 Storage (at high temperature) . 9 5.5 Storage (at low temperature) 10 5.6 Low air pressure . 11 5.7 Damp heat, steady state . 11 5.8 Damp heat, cyclic (12+12-hour cycle) . 12 5.9 Composite temperature/humidity cyclic test 12 5.10 Light expos

14、ure 15 5.10.1 Simulated solar radiation at ground level . 15 5.10.2 Simulated indoor daylight through window glass 15 5.10.3 Other radiation. 16 5.11 ESD Test 16 Bibliography 17 Figure 1 Temperature profile 7 Figure 2 Temperature profile 9 Figure 3 Preconditioning 13 Figure 4 Conditioning Exposure t

15、o humidity followed by exposure to cold . 14 Figure 5 Conditioning Exposure to humidity not followed by exposure to cold . 15 Table 1 Low test temperature . 6 Table 2 High test temperature 7 Table 3 Low test temperature . 8 Table 4 High test temperature 8 Table 5 Conditions of temperature and humidi

16、ty 11 IEC 61747-10-2:2014 IEC 2014 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ LIQUID CRYSTAL DISPLAY DEVICES Part 10-2: Environmental, endurance and mechanical test methods Environmental and endurance FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for

17、standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishe

18、s International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may part

19、icipate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement b

20、etween the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publica

21、tions have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for

22、 any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the correspond

23、ing national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any s

24、ervices carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC

25、National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attenti

26、on is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC

27、shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61747-10-2 has been prepared by IEC technical committee 110: Electronic display devices. This first edition of IEC 61747-10-2 cancels and replaces Clauses 1 and 3 of the first edition of IEC 61747

28、-5 published in 1998. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Examples of the test conditions have been added to each test method; b) References cited have been updated. 4 IEC 61747-10-2

29、:2014 IEC 2014 The text of this standard is based on the following documents: CDV Report on voting 110/528/CDV 110/575A/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accorda

30、nce with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 61747 series, published under the general title Liquid crystal display devices, can be found on the IEC website. NOTE It is intended that the other clauses of IEC 61747-5:1998 will be replaced by new parts in the IEC 61747 serie

31、s. The details of the intended changes are given in Annex D of IEC 61747-30-1:2012. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publicati

32、on. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IEC 61747-10-2:2014 IEC 2014 5 LIQUID CRYSTAL DISPLAY DEVICES Part 10-2: Environmental, endurance and mechanical test me

33、thods Environmental and endurance 1 Scope and object This part of IEC 61747 lists test methods applicable to liquid crystal display devices. It takes into account, wherever possible, the environmental test methods outlined in IEC 60068. NOTE Devices include cells and modules. The object of this stan

34、dard is to establish uniform preferred test methods with preferred values for stress levels for judging the environmental properties of liquid crystal display devices. In case of contradiction between this standard and a relevant specification, the latter should govern. 2 Normative references The fo

35、llowing documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068 (al

36、l parts), Environmental testing IEC 60068-2-1, Environmental testing Part 2-1: Tests Test A: Cold IEC 60068-2-2, Environmental testing Part 2-2: Tests Test B: Dry heat IEC 60068-2-5, Environmental testing Part 2-5: Tests Test Sa: Simulated solar radiation at ground level and guidance for solar radia

37、tion testing IEC 60068-2-13, Basic environmental testing procedures Part 2-13: Tests Test M: Low air pressure IEC 60068-2-14:1984, Environmental testing Part 2-14: Tests Test N: Change of temperature IEC 60068-2-30, Environmental testing Part 2-30: Tests Test Db: Damp heat, cyclic (12 h + 12 h cycle

38、) IEC 60068-2-38:2009, Environmental testing Part 2-38: Tests Test Z/AD: Composite temperature/humidity cyclic test IEC 60068-2-78, Environmental testing Part 2-78: Tests Test Cab: Damp heat, steady state IEC 60747 (all parts), Semiconductor devices IEC 60747-1, Semiconductor devices Part 1: General

39、 6 IEC 61747-10-2:2014 IEC 2014 IEC 60748-1, Semiconductor devices Integrated circuits Part 1: General ISO 18909:2006, Photography Processed photographic colour films and paper prints Methods for measuring image stability 3 Terms, definitions and symbols For the purposes of this standard, the terms,

40、 definitions and symbols given in IEC 60068, IEC 60747, IEC 60748-1 and IEC 61747-1 apply. 4 Standard atmospheric conditions for measurements and tests: Unless otherwise specified, all tests and measurements shall be carried out under standard atmospheric conditions for testing: Temperature: 15 C to

41、 35 C Relative humidity: 25 % to 85 % RH, where appropriate Air pressure: 86 kPa to 106 kPa (860 mbar to 1 060 mbar) The absolute humidity of the atmosphere shall not exceed 22 g/m 3 . 5 Test methods 5.1 General The choice of the appropriate tests depends on the type of devices. The relevant specifi

42、cation shall state which tests are applicable. Regarding the change of temperature, test Na, specified in IEC 60068-2-14, is applicable. 5.2 Rapid change of temperature: two-chamber method This test shall be in accordance with test Na, with the following specific requirements: the absolute humidity

43、of the atmosphere shall not exceed 20 g/m 3 ; the lower temperature T Ashall be specified in the relevant specification and shall be chosen from the test temperature of Table 1; the higher temperature T Bshall be specified in the relevant specification and shall be chosen from the test temperature o

44、f Table 2; Table 1 Low test temperature Low temperature T AC 50 3 45 3 40 3 35 3 30 3 25 3 20 3 15 3 10 3 5 3 0 3 IEC 61747-10-2:2014 IEC 2014 7 Table 2 High test temperature High temperature T BC +100 2 +95 2 +90 2 +85 2 +80 2 +75 2 +70 2 +65 2 +60 2 +55 2 +50 2 +45 2 +40 2 +35 2 +30 2 the exposure

45、 time t 1of each of the two temperatures depends upon the thermal capacity of the device. It shall be 3 h, 2 h, 1 h, 30 min or 10 min as specified in the relevant specification. Where no exposure period is prescribed in the relevant specification it is understood to be 3 h; t 2is the time from unloa

46、ding from one chamber to loading to the other chamber. The transition time should be: 2 min to 3 min; 20 s to 30 s; less than 10 s; the first cycle comprises the two exposure times t 1and the two transition times t 2(see Figure 1); the number of cycles shall be 5, 10, 50, 100, 200 unless otherwise s

47、pecified in the relevant specification; initial measurements: an external visual examination; mechanical, electrical and optical tests: as given in the relevant specification; final measurements: an external visual examination; mechanical, electrical, and optical tests: as specified at the initial m

48、easurements and in the relevant specification. A = start of first cycle B = end of first cycle and start of second cycle NOTE The dotted curve is explained in 1.3.1.5 of IEC 60068-2-14:1984. Figure 1 Temperature profile for the two-chamber method A B t 110 t 110 t 1t 2t 2T BT At 1Time t First cycle

49、Temperature in the chamber IEC 8 IEC 61747-10-2:2014 IEC 2014 Example test conditions (for thermal shock test): T a= -40 C, T b= +85 C, t 1= 30 min, t 2= 3 min, 50 cycles T a= -40 C, T b= +85 C, t 1= 30 min, t 2= 3 min, 100 cycles T a= -30 C, T b= +80 C, t 1= 30 min, t 2= 3 min, 100 cycles 5.3 Specified change rate of temperature: one-chamb