IEC 60745-2-9 Edition 2.1-2008 Hand-held motor-operated electric tools - Safety - Part 2-9 Particular requirements for tappers《手持式电动工具.安全性.第2-9部分 攻丝机的特殊要求》.pdf

《IEC 60745-2-9 Edition 2.1-2008 Hand-held motor-operated electric tools - Safety - Part 2-9 Particular requirements for tappers《手持式电动工具.安全性.第2-9部分 攻丝机的特殊要求》.pdf》由会员分享，可在线阅读，更多相关《IEC 60745-2-9 Edition 2.1-2008 Hand-held motor-operated electric tools - Safety - Part 2-9 Particular requirements for tappers《手持式电动工具.安全性.第2-9部分 攻丝机的特殊要求》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60745-2-9Edition 2.1 2008-06INTERNATIONAL STANDARD NORME INTERNATIONALEHand-held motor-operated electric tools Safety Part 2-9: Particular requirements for tappers Outils lectroportatifs moteur Scurit Partie 2-9: Rgles particulires pour les taraudeuses IEC60745-2-9:2003+A1:2008 THIS PUBLICATION

2、 IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from e

3、ither IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. D

4、roits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la

5、CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 G

6、eneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The techni

7、cal content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of cri

8、teria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Availa

9、ble on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotec

10、hnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de l

11、a CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la C

12、EI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffren

13、ts critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouv

14、elles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les lan

15、gues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez

16、-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60745-2-9Edition 2.1 2008-06INTERNATIONAL STANDARD NORME INTERNATIONALEHand-held motor-operated electric tools Safety Part 2-9: Particular requirements for tappers Outils lectroportatifs moteur Scurit Partie 2-9: Rgles particuli

17、res pour les taraudeuses INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE CAICS 25.140.20 PRICE CODECODE PRIXISBN 2-8318-9702-5 2 60745-2-9 IEC:2003+A1:2008 CONTENTS FOREWORD.3 1 Scope.5 2 Normative references .5 3 Terms and definitions .5 4 General requirements.5

18、 5 General conditions for the tests 5 6 Void5 7 Classification5 8 Marking and instructions.5 9 Protection against access to live parts6 10 Starting 6 11 Input and current 6 12 Heating 6 13 Leakage current .6 14 Moisture resistance 6 15 Electric strength .6 16 Overload protection of transformers and

19、associated circuits .6 17 Endurance7 18 Abnormal operation 7 19 Mechanical hazards7 20 Mechanical strength .7 21 Construction.7 22 Internal wiring.7 23 Components .7 24 Supply connection and external flexible cords 7 25 Terminals for external conductors.7 26 Provision for earthing .7 27 Screws and c

20、onnections.7 28 Creepage distances, clearances and distances through insulation8 29 Resistance to heat, fire and tracking.8 30 Resistance to rusting8 31 Radiation, toxicity and similar hazards8 Annexes .9 Annex K (normative) Battery tools and battery packs .9 Annex L (normative) Battery tools and ba

21、ttery packs provided with mains connection or non-isolated sources.9 Bibliography9 60745-2-9 IEC:2003+A1:2008 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS SAFETY Part 2-9: Particular requirements for tappers FOREWORD 1) The International Electrotechnical Comm

22、ission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and

23、in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee

24、interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordan

25、ce with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all intere

26、sted IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsib

27、le for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence be

28、tween any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All u

29、sers should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or o

30、ther damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication

31、. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such pat

32、ent rights. This part of International Standard IEC 60745 has been prepared by subcommittee 61F: Safety of hand-held motor-operated electric tools, of IEC technical committee 61: Safety of household and similar electrical appliances. This consolidated version of IEC 60745-2-9 consists of the second

33、edition (2003) documents 61F/464/FDIS and 61F/488/RVD and its amendment 1 (2008) documents 61F/674/CDV and 61F/724/RVC. The technical content is therefore identical to the base edition and its amendment and has been prepared for user convenience. It bears the edition number 2.1. A vertical line in t

34、he margin shows where the base publication has been modified by amendment 1. The French version of this standard has not been voted upon. 4 60745-2-9 IEC:2003+A1:2008 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This part 2 is to be used in conjunction with th

35、e latest edition of IEC 60745-1, Hand-held motor-operated electric tools Safety Part 1: General requirements, and its amendments. It was established on the basis of the third edition (2001) of that standard. NOTE 1 When “Part 1” is mentioned in this standard, it refers to IEC 60745-1. This part 2 su

36、pplements or modifies the corresponding clauses of IEC 60745-1, so as to convert that publication into the IEC standard: Safety requirements for electric tappers. When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies as far as is reasonable. When this standard

37、 states “addition”, “modification” or “replacement”, the relevant text in Part 1 is to be adapted accordingly. NOTE 2 The following numbering system is used: subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1; additional annexes are lettered AA, BB,

38、etc. NOTE 3 In this standard, the following print types are used: requirements: in roman type; test specifications: in italic type; notes: in smaller roman type. Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the associated noun are also

39、 in bold. The committee has decided that the contents of the base publication and its amendments will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be

40、reconfirmed, withdrawn, replaced by a revised edition, or amended. 60745-2-9 IEC:2003+A1:2008 5 HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS SAFETY Part 2-9: Particular requirements for tappers 1 Scope This clause of Part 1 is applicable except as follows: Addition: This standard applies to tappers. 2 No

41、rmative references This clause of Part 1 is applicable. 3 Terms and definitions This clause of Part 1 is applicable except as follows: 3.101 tapper tool intended for cutting internal screw threads 4 General requirements This clause of Part 1 is applicable. 5 General conditions for the tests This cla

42、use of Part 1 is applicable. 6 Void 7 Classification This clause of Part 1 is applicable. 8 Marking and instructions This clause of Part 1 is applicable, except as follows: 6 60745-2-9 IEC:2003+A1:2008 8.1 Addition: In addition the tool shall have the following marking: maximum diameter, in millimet

43、res, of thread which can be cut. The diameter shall refer to a unified ISO thread to be cut into steel having a tensile strength of 390 N/mm and a thickness of twice the thread diameter, unless otherwise indicated on the tool. 9 Protection against access to live parts This clause of Part 1 is applic

44、able. 10 Starting This clause of Part 1 is applicable. 11 Input and current This clause of Part 1 is applicable. 12 Heating This clause of Part 1 is applicable, except as follows: 12.4 Replacement: The tool is operated intermittently for 30 cycles or until temperatures stabilise, whichever is achiev

45、ed first, each cycle comprising a period of continuous operation of 30 s and a rest period of 90 s with the tool switched off, the tool being loaded during the periods of operation by means of a brake adjusted so as to attain rated input or rated current. The temperature rises are measured at the en

46、d of the “on” period. At the manufacturers option the tool may be operated continuously until thermal stabilisation. 13 Leakage current This clause of Part 1 is applicable. 14 Moisture resistance This clause of Part 1 is applicable. 15 Electric strength This clause of Part 1 is applicable. 16 Overlo

47、ad protection of transformers and associated circuits This clause of Part 1 is applicable. 60745-2-9 IEC:2003+A1:2008 7 17 Endurance This clause of Part 1 is applicable. 18 Abnormal operation This clause of Part 1 is applicable. 19 Mechanical hazards This clause of Part 1 is applicable. 20 Mechanica

48、l strength This clause of Part 1 is applicable, except as follows: 20.5 This subclause is not applicable. 21 Construction This clause of Part 1 is applicable, except as follows: 21.32 This subclause is not applicable. 22 Internal wiring This clause of Part 1 is applicable. 23 Components This clause

49、of Part 1 is applicable. 24 Supply connection and external flexible cords This clause of Part 1 is applicable. 25 Terminals for external conductors This clause of Part 1 is applicable. 26 Provision for earthing This clause of Part 1 is applicable. 27 Screws and connections This clause of Part 1 is applicable. 8 60745-2-9 IEC:2003+A1:2008 28 Creepage distances, clearances and distances t