IEC 60079-33-2012 Explosive atmospheres - Part 33 Equipment protection by special protection s 《爆炸性环境.第33部分 s 型外壳专门保护设备防护》.pdf

《IEC 60079-33-2012 Explosive atmospheres - Part 33 Equipment protection by special protection s 《爆炸性环境.第33部分 s 型外壳专门保护设备防护》.pdf》由会员分享，可在线阅读，更多相关《IEC 60079-33-2012 Explosive atmospheres - Part 33 Equipment protection by special protection s 《爆炸性环境.第33部分 s 型外壳专门保护设备防护》.pdf（84页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60079-33 Edition 1.0 2012-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Explosive atmospheres Part 33: Equipment protection by special protection “s” Atmosphres explosives Partie 33: Protection du matriel par protection spciale “s“ IEC60079-33:2012 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyr

2、ight 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member Nati

3、onal Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs.

4、 Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si

5、vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919

6、 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The tech

7、nical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications

8、 by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released.

9、Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the Inte

10、rnational Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internation

11、ale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer q

12、ue vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle do

13、nne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par

14、 email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrote

15、chnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60079-33 Edition 1.0 2012-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Explosive atmospheres Pa

16、rt 33: Equipment protection by special protection “s” Atmosphres explosives Partie 33: Protection du matriel par protection spciale “s“ INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE W ICS 29.260.20 PRICE CODE CODE PRIX ISBN 978-2-83220-359-0 Registered trademar

17、k of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 60

18、079-33 IEC:2012 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope . 9 2 Normative references . 9 3 Terms and definitions . 10 4 General 11 4.1 Application 11 4.2 Equipment group and temperature classification 11 4.3 Level of protection (equipment protection level (EPL) . 11 4.4 Manufacturers justificat

19、ion 12 4.5 Verification 12 5 Independent verifier 12 5.1 General . 12 5.2 Competence 12 5.3 Duties 13 5.4 Acceptance . 13 5.5 Independence 13 6 Design and construction . 13 6.1 Principles of an integrated approach to explosion safety . 13 6.2 Design and construction 14 6.3 Overloading of equipment 1

20、4 6.4 Potential ignition sources 14 6.4.1 Hazards arising from different ignition sources 14 6.4.2 Hazards arising from overheating 14 6.4.3 Hazards arising from pressure compensation operations . 14 6.5 Requirements in respect of safety-related devices . 14 7 Application of equipment protection lev

21、els (EPL) 15 7.1 Equipment with EPL Ma 15 7.2 Equipment with EPL Mb 15 7.3 Equipment with EPL Ga . 16 7.4 Equipment with EPL Gb . 17 7.5 Equipment with EPL Gc . 17 7.6 Equipment with EPL Da . 17 7.7 Equipment with EPL Db . 18 7.8 Equipment with EPL Dc . 18 8 Preparation of assessment and test specif

22、ication . 18 8.1 General . 18 8.2 Assessment and test specification . 19 8.3 Assessment and testing. 19 8.4 Reporting results of the assessment and test specification 19 9 Ignition hazard assessment 19 9.1 General . 19 9.2 Protective measures 19 9.3 Explanation of the ignition hazard assessment proc

23、edure 20 9.4 Examples of ignition hazard assessment . 20 10 Application of special protection “s” 20 60079-33 IEC:2012 3 10.1 General . 20 10.2 Justification for the application of special protection “s” . 20 10.2.1 Application 20 10.2.2 Equipment substantially meeting the requirements for the recog

24、nized types of protection . 21 10.2.3 Equipment outside the scope of recognized types of protection . 21 10.2.4 Protection technique with no alignment to the recognized types of protection 21 10.2.5 Enhanced EPL through additional means of protection 22 10.2.6 Combination of approaches . 22 10.3 Ada

25、ption of recognized types of protection 22 10.4 Other innovative means of ensuring safety 22 10.5 Connection of conductor and cables 22 11 Type verification and tests 23 11.1 General . 23 11.2 Temperature measurement test . 23 12 Routine verification and test . 23 13 Documentation . 23 14 Ex compone

26、nts . 23 15 Marking 23 15.1 General . 23 15.2 Marking for Ex “s” only 23 15.3 Marking for Ex “s” with other recognized types of protection 23 16 Certificate information 24 16.1 Certificate for Ex “s” only . 24 16.2 Certificate for Ex “s” with other recognized types of protection 24 16.3 Specific con

27、ditions of use 24 16.4 Schedule of limitations 24 17 Instructions . 24 Annex A (informative) Explanation of the ignition hazard assessment procedure 25 Annex B (informative) Examples of ignition hazard assessment . 31 Bibliography 37 Figure A.1 Relationship between ignitions source definitions . 26

28、Table A.1 Recommended documentation of initial assessment of equipment related ignition sources. 27 Table A.2 Example for reporting identification of ignition hazards (step 1) and first assessment (step 2) 28 Table A.3 Example for reporting determination of preventive or protective measures (step 3)

29、 and concluding estimation and EPL assignment (step 4) . 29 Table B.1 Common cases demonstrating the use of the reporting method Electrostatic discharge 33 Table B.2 Ignition hazard assessment report for a linear motor with permanent magnets in the table-track, EPL Gb, in addition to the basic requi

30、rements of IEC 60079-0 (for example material characteristics, electrostatic, earthing) 35 4 60079-33 IEC:2012 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ EXPLOSIVE ATMOSPHERES Part 33: Equipment protection by special protection “s” FOREWORD 1) The International Electrotechnical Commission (IEC) is a

31、 worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to ot

32、her activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the

33、 subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with condition

34、s determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National

35、 Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in

36、 which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Pub

37、lication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC i

38、s not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its te

39、chnical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other I

40、EC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the sub

41、ject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60079-33 has been prepared by IEC technical committee 31: Equipment for explosive atmospheres. The text of this standard is based on the following documents: FDIS Report

42、 on voting 31/997/FDIS 31/1011/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 60079 series, pub

43、lished under the general title Explosive atmospheres, can be found on the IEC website. 60079-33 IEC:2012 5 The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to

44、 the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 60079-33 IEC:2012 INTRODUCTION This part of IEC 60079 was created in response to a request from the IECEx certification system to provide a set of requirements to be

45、used for certification within the IECEx product certification scheme when the standards for existing types of protection were not applicable. The present standard refers to the use of one or more independent verifiers, in accordance with ISO/IEC rules on the writing of standards that mitigate agains

46、t specifying particular forms of conformity assessment. The IECEx system will specify how the term “independent verifier“ will be interpreted for the purposes of the scheme. For example, it may specify that in the case of three independent verifiers they shall all be certification body members of th

47、e scheme, each accepted specifically for the purpose of assessing special protection applications and each from a separate member country of the system. The purpose of IEC 60079-33 special protection “s” for any equipment protection level (EPL) is to allow design, assessment and testing of equipment

48、 or parts of equipment that cannot be fully assessed within a recognized type of protection or combination of recognized types of protection because of functional or operational limitations and where the desired equipment protection level can be achieved by the use of this standard. Special protecti

49、on “s” allows a design concept that cannot comply in full with recognized types of protection, or where the design concept is not covered by recognized types of protection. When specification for the equipment includes aspects as given above, additional information and data may be required from technical research, evaluation of existing data and information. Manufacturers should first consider the possibilities for design to the recog