TIA-464-C-1-2004 Telecommunications Multiline Terminal Systems Requirements for PBX Switching Equipment Addendum 1 (ANSI Withdrawn 07 24 2015)《电信-多线终端系统-PBX交换设备要求》.pdf

《TIA-464-C-1-2004 Telecommunications Multiline Terminal Systems Requirements for PBX Switching Equipment Addendum 1 (ANSI Withdrawn 07 24 2015)《电信-多线终端系统-PBX交换设备要求》.pdf》由会员分享，可在线阅读，更多相关《TIA-464-C-1-2004 Telecommunications Multiline Terminal Systems Requirements for PBX Switching Equipment Addendum 1 (ANSI Withdrawn 07 24 2015)《电信-多线终端系统-PBX交换设备要求》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、 ANSI/TIA-464-C-1-2004 APPROVED: JUNE 14, 2004 REAFFIRMED: MAY 19, 2009 WITHDRAWN: JULY 24, 2015 TIA-464-C-1 June 2004Telecommunications Multiline Terminal Systems Requirements for PBX Switching Equipment, Addendum 1 NOTICE TIA Engineering Standards and Publications are designed to serve the public

2、interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards an

3、d Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestical

4、ly or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard o

5、r Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory

6、limitations before its use. Any use of trademarks in this document are for information purposes and do not constitute an endorsement by TIA or this committee of the products or services of the company. (From Project No. 3-3673-RV3-AD1-WD, formulated under the cognizance of the TIA TR-41 Performance

7、and Accessibility for Communications Products.) Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Technology (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or change

8、d in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IP

9、R consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the s

10、cope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warran

11、t or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the formulation, develo

12、pment or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Procedures for American National Standards) then (i) TIA disclaims any duty or obligat

13、ion to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see TIA Procedures for American National Standards Annex C.1.2.3) of Essential Patent(s) and published pendin

14、g patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the cont

15、ents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCU

16、RACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WA

17、RRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRE

18、CT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTR

19、ACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITA

20、TIONS. TIA-464-C-1 1FOREWORD (This foreword is not part of this Standard.) This document is an addendum to ANSI/TIA-464-C, Telecommunications Multiline Terminal Systems Requirements for PBX Switching Equipment. It was developed and produced by TIA Subcommittee TR-41.1, Multiline Terminal Systems in

21、accordance with ANSI and TIA procedural guidelines and represents the consensus position of the Subcommittee, which served as the formulating group. It has also received the concurrence of Engineering Committee TR-41, User Premises Telecommunications Requirements. This addendum makes the following c

22、hanges to ANSI/TIA-464-C: - Change sections 6.2.3 - 6.2.5 to make them align with the new loss plan changes in ANSI/TIA-968-A-1 standard mandated by FCC for Part 68 product registration and new changes in analog telephone SLR values in the latest revision of ANSI/TIA-470.110-C. - Change all referenc

23、es to TIA/EIA/IS-968 to ANSI/TIA-968-A or ANSI/TIA-968-A-1. - Correct the editorial mistakes in the existing ANSI/TIA-464-C standard. TR-41.1 acknowledges the contribution made by the following individuals in the development of this addendum to ANSI/TIA-464-C Standard. Name Representing Roger Britt

24、Nortel Tailey Tung Siemens (Editor) Dick Frank Dietrich Lockard Group Suggestions for improvement of this Standard are welcome. They should be sent to: Telecommunications Industry Association Engineering Department Suite 300 2500 Wilson Boulevard Arlington, VA 22201 TIA-464-C-1 21. Introduction The

25、purpose of this addendum is to update ANSI/TIA-464-C to make it in-line with the new changes in ANSI/TIA-968-A and ANSI/TIA-968-A-1 standards mandated by FCC for Part 68 product registration and the new changes in analog telephone SLR values in the latest revision of ANSI/TIA-470.110-C. It also corr

26、ects the editorial mistakes in the existing ANSI/TIA-464-C standard. The TIA TR41.9 Subcommittee advanced the TIA/EIA/IS-968 interim standard to an ANSI approved TIA-968-A standard on October 29, 2002. They have made significant changes to the ANSI/TIA-968-A loss plan table and the signal power limi

27、tation requirements in ANSI/TIA-968-A-1 addendum to ANSI/TIA-968-A standard. The new ANSI/TIA-968-A-1 loss plan relaxes the encoded analog content signal power limitations in ANSI/TIA-968-A, section 4.5.10 and the 2-wire and 4-wire lossless tie trunk signal power limitations in 4.5.2.1.2. These chan

28、ges also coordinate with changes to the allowable net amplification between port requirements in Table 4.6. The result is less allowable net amplification between some ports and more allowable net amplification between other ports. The new ANSI/TIA-968-A-1 loss plan changes impact significantly the

29、ANSI/TIA-464-C, section 6.2.5 for PBX loss range requirements. 2. Scope The requirements in this addendum are intended to align the requirements in ANSI/TIA-464-C standard for Private Branch Exchange (PBX) systems with the new changes in ANSI/TIA-968-A and ANSI/TIA-968-A-1 standards mandated by FCC

30、for Part 68 product registration. It also intended to assure satisfactory user voicegrade services in a high percentage of installations. If cases arise that have not been adequately addressed in this standard, any resulting problems should be resolved through the cooperation of the customer, the ca

31、rrier, and the equipment supplier. It is recognized that some PBX products may not be accommodated by this standard because of non-standard line interfaces; e.g., proprietary digital station interfaces. In such systems, the station apparatus must be considered as a whole with the PBX and its associa

32、ted station wiring, and the overall system must be described in terms of an acoustic (user) to an electrical (network) standard. 3. Revise technical requirements in sections 6.2.3, 6.2.4 and 6.2.5. 6.2.3 Insertion Loss Criteria for PBX The nominal values for PBX port-to-port connections are given by

33、 the loss plan presented in Table 12. The PBX interfaces described in the loss plan are given in 4.3 and illustrated in Figure 1. 6.2.3.1 Port-to-Port Loss Table Interpretation In Table 12, arrows at the row and column designators indicate the transmission direction in which the coordinate loss valu

34、es are to be inserted. The negative values in the Port-to-Port loss table denote gain; e.g., -3 indicates 3 dB gain. For example, coordinate 1B indicates a nominal port-to-port loss of 9 dB from the ONS interface to the OPS interface, and coordinate 2A indicates a 9 dB loss in the other direction, f

35、rom the OPS interface to the ONS interface. The port designations in Table 12 indicate the specific application for which the loss plan was developed. These ports may, however, be used for other applications, as long as the resulting gains comply with the ANSI/TIA-968-A requirements for allowable ne

36、t amplification between ports. (Ref 42, Section 4.5.2.5) 6.2.3.2 Port-to-Port Loudness Ratings Table Interpretation Table 13 is provided to show the relationship between OLR and SLR, Loss, and RLR. TIA-464-C-1 3For example, for an ONS to OPS connection, the ONS SLR is 4 dB, the PBX loss is 9 dB (coo

37、rdinate 1B in Table 12), and the OPS RLR is 3 dB. The overall loudness ratings is therefore 4 + 9 3 = 10 dB. See Annex B2 for further information on loudness ratings. Table 12 - PBX Loss Plan A B C D E F G ONS OPS DGS DAL AAL(A) AAL(D) ATT Loss 1 ONS 12 9 3 3 3 6 9 2 OPS 9 6 0 0 0 0 3 3 DGS 9 6 0 0

38、0 3 3 4 DAL 9 6 0 0 0 3 3 5 AAL(A) 0 0 -6 -6 0 0 0 6 AAL(D) 3 0 -3 -3 0 0 0 7 ATT 6 0 0 0 0 0 0 Notes: 1. The units for all Loss values are dB. 2. Losses have been selected as multiples of 3 dB, in the assumption that this may make implementation easier. 3. A loss of 3 dB is included in the ONS full

39、 channel loss plan as the long-term objective, however the ONS SLR of most existing analog telephones is significantly quieter than 4 dB. Therefore, the loss values specified in the ONS row may be reduced by 3 dB until analog telephones meeting ONS SLR of 4 dB are available Table 13 - PBX Loudness R

40、atings ONS OPS DGS DAL AAL(A) AAL(D) ATT RLR -7 -3 2 2 6 3 1 SLR OLR ONS 4 9 10 9 9 13 13 14 OPS 8 10 11 10 10 14 11 12 DGS 8 10 11 10 10 14 14 12 DAL 8 10 11 10 10 14 14 12 AAL(A) 17 10 14 13 13 23 20 18 AAL(D) 14 10 11 13 13 20 17 15 ATT 15 14 12 17 17 21 18 16 TIA-464-C-1 4Notes: 1. The units for

41、 all SLR, RLR and Loss values are dB. 2. The ONS SLR is 4 dB less than in ANSI/EIA/TIA-464-B; of this 3 dB is due to a 3 dB increase in send gain in TIA-470.110-C and 1 dB is due to a new methodology for determining ONS loudness ratings, which is detailed in TIA-470.11-C Annex E. The ONS RLR is 1 dB

42、 less than in ANSI/EIA/TIA-464-B due to the new methodology in TIA-470.11-C Annex E. 3. The OPS SLR is 3 dB less than in ANSI/EIA/TIA-464-B due to a 3 dB increase in send gain in TIA-470.110-C 4. The SLR and RLR values include the following network losses: AAL(A) and AAL(D) include a nominal 6 dB ce

43、ntral office loss ATT includes a 2 dB line loss. 6.2.4 PBX Loss Plan Assumptions The port-to-port losses for PBXs were developed based on the loss plans for public and private networks. The PBX loss plan is intended to provide satisfactory Grade-of-service (GoS) performance and compatibility with th

44、e public and private network loss plans. The following assumptions were the prime considerations: (1) The transmission loss and level plan of the PSTN, which is primarily an all-digital network with some fixed loss as described in ANSI T1.508-2004 (Ref 8), forms a basis for the private network loss

45、plan. (2) Digital end offices insert 6 dB of loss, as described in T1.508, in the receive direction of analog access lines to ensure network stability and echo control. (3) Transmission facilities to be used have losses compatible with the PBX port-to-port losses. (4) PBX port-to-port losses associa

46、ted with analog interfaces apply to any trunks with analog terminations at the PBX. (5) PBX port-to-port losses associated with digital interfaces apply to any trunks with digital terminations at the PBX. (6) Non-proprietary PBX stations have the following loudness ratings: Station SLR RLR Notes OPS

47、 8 -3 1 ONS 4 -7 2 DGS 8 2 3 Notes: 1. The OPS (off premises station) ratings are representative of 2500-type sets operating on 26 gauge / 2.75 km loops with normal 48 battery feed and 600 ohm termination, as measured at a VG OPS port. See ANSI/TIA-470.110-C, Annex E for further details 2. The ONS (

48、on premises station) ratings are representative of 2500-type sets operating on very short loops with the typical current-limited battery feed and 600 ohm termination of VG ONS ports. See ANSI/TIA-470.110-C, Annex E for further details. 3. The DGS (digital station) ratings are chosen to improve inter

49、operability with the ITU-T standard SLR/RLR levels for digital sets of 8 and 2. See ANSI/TIA-810-A (Ref 16) for further details. TIA-464-C-1 56.2.5 PBX Loss Ranges and ANSI/TIA-968-A Requirements 6.2.5.1 Recommended Loss Ranges The port-to-port losses in Table 12 are the recommended nominal values. Although there are no mandatory loss ranges associated with these values, it is desirable that the average 1 kHz loss fall within +0.5 dB of the nominal loss values given in Table 12. 6.2.5.2 ANSI/TIA-968-A Requirements Tables