SANS 101-2009 White metal designated WM 6《白色合金命名WM 6》.pdf

《SANS 101-2009 White metal designated WM 6《白色合金命名WM 6》.pdf》由会员分享，可在线阅读，更多相关《SANS 101-2009 White metal designated WM 6《白色合金命名WM 6》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-22866-8 SANS 101:2009Edition 1.1SOUTH AFRICAN NATIONAL STANDARD White metal designated WM 6 Published by SABS Standards Division 1 Dr Late

4、gan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 101:2009 Edition 1.1 Table of changes Change No. Date Scope Amdt 1 2009 Amended to delete a referenced standard method that has been withdrawn. Foreword This South African standard wa

5、s approved by National Committee SABS TC 1078, Engineering materials Non-ferrous metals, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This document was published in September 2009. This document supersedes SANS 101:2004 (edition 1

6、). A vertical line in the margin shows where the text has been technically modified by amendment No. 1. SANS 101:2009 Edition 1.1 1 Contents Page Foreword 1 Scope . 3 2 Normative references . 3 3 Definition 3 4 Requirements . 3 5 Marking 4 6 Sampling and compliance with the standard . 4 7 Inspection

7、 and methods of test 5 Figure . 6 SANS 101:2009 Edition 1.1 2 This page is intentionally left blank SANS 101:2009 Edition 1.1 3 White metal designated WM 6 1 Scope This standard covers a grade of white metal designated WM 6, according to its average tin content. 2 Normative references The following

8、normative documents contain provisions, which, through reference in this text, constitute provisions of this standard. All normative documents are subject to revision and, since any reference to a normative document is deemed to be a reference to the latest edition of that document, parties to agree

9、ments based on this standard are encouraged to take steps to ensure the use of the most recent editions of the normative documents indicated below. Information on currently valid national and international standards can be obtained from the SABS Standards Division. BS 3338-17, Methods for the sampli

10、ng and analysis of tin and tin alloys Part 17: Method for the determination of cadmium in solders and white metal bearing alloys (photometric method). SANS 5244 (SABS SM 244), Aluminium content of printers metal and white metal. Amdt 1 SANS 5732 (SABS SM 732), Tin content of tin and lead alloys. 3 D

11、efinition For the purposes of this standard, the following definition applies: lot number of white metal ingots or bars of the same designation, from the same manufacturer, submitted at any one time for inspection and testing 4 Requirements 4.1 Chemical composition The ingots or bars shall conform t

12、o the chemical composition shown in table 1. SANS 101:2009 Edition 1.1 4 Table 1 Chemical composition 1 2 3 4 Symbol Element %, min. %, max. WM 6 Tin Antimony Copper 5,0 13,0 7,0 15,0 0,3 Iron Zinc 0,05 0,01 Other elements totalaLead remainder 0,3 aRefers to all elements other than those given in th

13、e table. 4.2 Physical condition The metal shall be supplied in the form of bars or ingots and shall be free from slag, dross, and undue segregation. 5 Marking The following information shall appear in legible and durable marking on each ingot or bar: a) the name or trade mark of the manufacturer or

14、supplier; and b) the symbol WM 6. 6 Sampling and compliance with the standard1)6.1 Sampling The following sampling procedure shall be applied in determining whether a lot complies with the relevant requirements of the standard. The sample taken shall be deemed to represent the lot. From the lot draw

15、 at random the number of ingots or bars given, as relevant, in column 2 of table 2 relative to the appropriate lot size shown in column 1. Table 2 Sampling 1 2 Ingots or bars Lot size Sample size 221101201003001 2 3 More than 300 5 1) These methods are revised from time to time. In all cases the lat

16、est edition of the individual method should be used. SANS 101:2009 Edition 1.1 5 6.2 Compliance The lot shall be deemed to comply with the requirements of the standard if, after inspection and testing, the samples taken in accordance with 6.1 are found to comply with the appropriate requirements of

17、the standard. 7 Inspection and methods of test 7.1 Inspection Inspect all the ingots or bars drawn in accordance with 6.1 for compliance with the requirements of 4.2 and clause 5. 7.2 Methods of test 7.2.1 General Any reliable method of chemical analysis may be used for determining the individual co

18、nstituents of the alloy(s). Suitable methods are listed in 7.2.2, 7.2.3 and 7.2.5 and shall be the methods used in all cases of dispute. Amdt 1 7.2.2 Test sample for chemical analysis Obtain the sample for chemical analysis by making cuts of depth 15 mm with a clean saw having 55 teeth per 100 mm in

19、 each sample ingot at regular intervals of not more than 50 mm (see figure 1). Do not use any lubricant. Treat the sawings carefully with a magnet to remove any particles of steel which may have been introduced during cutting. Sieve the sawings through a small sieve of aperture size 250 m and weigh

20、into coarse and fine fractions. Mix each thoroughly and take proportional masses of each when weighing samples for analysis. 7.2.3 Tin content and lead alloys Tin content and lead alloys shall comply with the requirements of SANS 5732. 7.2.4 Deleted by amendment No. 1. 7.2.5 Cadmium in solders and w

21、hite metal Cadmium in solders and white metal bearing alloys shall comply with the requirements of BS 3338-17. SANS 101:2009 Edition 1.1 6 Figure 1 Sampling method SABS SABS Standards Division The objective of the SABS Standards Division is to develop, promote and maintain South African National Sta

22、ndards. This objective is incorporated in the Standards Act, 2008 (Act No. 8 of 2008). Amendments and Revisions South African National Standards are updated by amendment or revision. Users of South African National Standards should ensure that they possess the latest amendments or editions. The SABS

23、 continuously strives to improve the quality of its products and services and would therefore be grateful if anyone finding an inaccuracy or ambiguity while using this standard would inform the secretary of the technical committee responsible, the identity of which can be found in the foreword. Tel:

24、 +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 The SABS offers an individual notification service, which ensures that subscribers automatically receive notification regarding amendments and revisions to South African National Standards. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: saless

25、abs.co.za Buying Standards Contact the Sales Office for South African and international standards, which are available in both electronic and hardcopy format. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za South African National Standards are also available online from the

26、 SABS website http:/www.sabs.co.za Information on Standards The Standards Information Centre provides a wide range of standards-related information on both national and international standards, and is the official WTO/TBT enquiry point for South Africa. The Centre also offers an individual updating

27、service called INFOPLUS, which ensures that subscribers automatically receive notification regarding amendments to, and revisions of, international standards. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za Copyright The copyright in a South African National Standard or any

28、other publication published by the SABS Standards Division vests in the SABS. Unless exemption has been granted, no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means without prior written permission from the SABS Standards Division. This does not prec

29、lude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any purpose other than implementation, prior written permission must be obtained. Details and advice can be obtained from the Senior Manager. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za