SAE AS 6014A-2011 HOSE ASSEMBLY POLYTETRAFLUOROETHYLENE PARA ARAMID REINFORCED 275 4000 PSI MAX FLARELESS TITANIUM FITTINGS STRAIGHT TO 45 DEGREE《4000 psi 275 ℉直通对45弯头的非扩口钛管接头用对位芳纶增强聚.pdf

《SAE AS 6014A-2011 HOSE ASSEMBLY POLYTETRAFLUOROETHYLENE PARA ARAMID REINFORCED 275 4000 PSI MAX FLARELESS TITANIUM FITTINGS STRAIGHT TO 45 DEGREE《4000 psi 275 ℉直通对45弯头的非扩口钛管接头用对位芳纶增强聚.pdf》由会员分享，可在线阅读，更多相关《SAE AS 6014A-2011 HOSE ASSEMBLY POLYTETRAFLUOROETHYLENE PARA ARAMID REINFORCED 275 4000 PSI MAX FLARELESS TITANIUM FITTINGS STRAIGHT TO 45 DEGREE《4000 psi 275 ℉直通对45弯头的非扩口钛管接头用对位芳纶增强聚.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, PARAARAMID REINFORCED, 275 F, 4000 PSI MAX, FLARELESS, TITANIUM FITTINGS, STRAIGHT TO 45 DEGREE AS6014Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transm

2、itted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB

3、 ADDRESS: http:/www.sae.org ISSUED 2009-02REVISED 2011-12THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3D REV. AFEDERAL SUPPLY CLASS 4720 AS6014SHEET 1 OF 5REV.APROCUREMENT SPECIFICATION: /2/ AS5951SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of techn

4、icalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay b

5、ereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS6014ARATIONALE REVISE TITLE FOR 4000 PSI MAX USAGE, REMOVED /21/ FROM FIG. 1, AND CORRECTED USAG

6、E CHARACTERISTICS, MARKING, AND PROOF PRESSURE REQUIREMENTS. FIGURE 1 - FLARELESS HOSE ASSEMBLY, STRAIGHT TO 45 DEGREE ELBOW FIGURE 2 - POLYESTER ABRASION SLEEVE CUFF /20/ AEROSPACE STANDARD AS6014SHEET 2 OF 5REV.AHOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, PARA ARAMID REINFORCED, 275 F, 4000 PSI MAX, F

7、LARELESS, TITANIUM FITTINGS, STRAIGHT TO 45 DEGREE TABLE 1 - HOSE AND FITTING DIMENSIONS BASIC HOSE ASSEMBLY NO.AS6014 SIZE CODE SIZE /14/ FITTING TYPE REF THREAD T PER AS8879 HOSE IDMIN A1 MAXA2 MAXREF BGAGE BASICC /7/ FITTING DIA. MIN.REF /9/ D1 &D5 REF /9/ D2 &D6 REF/9/ D3 REF/9/ D4 E/8/ MAX REF

8、FHEX G1 MIN G1 MAX STRAIGHTFITTING BALL SIZE MIN THRU /7/ INELBOW FITTING BALL SIZE MIN THRU /7/INEE.250 .250 SE.4375-20UNJF-3B .5625-18UNJF-3B .212 .212 1.92 2.02 2.37 2.37 .2930.4120.133 .133 .16 .16 .055 .055 .11 .11 .038.038.68 .68 .56 .69 .328 .368 .458 .498 .120 .120 .113 .113 GGG.375 .375 .37

9、5 RSE.4375-20UNJF-3B .5625-18UNJF-3B .7500-16UNJF-3B .298 .298 .298 2.12 2.16 2.29 2.51 2.55 2.68 .2930.4120.5600.133 .226 .226 .16 .16 .19 .055 .055 .066 .11 .11 .12 .038.038.038.85 .85 .85 .56 .69 .88 .328 .368 .487 .458 .498 .617 .120 .203 .203 .113 .192 .192 HHH.500 .500 .500 RSE.5625-18UNJF-3B

10、.7500-16UNJF-3B .8750-14UNJF-3B .391 .391 .391 2.38 2.51 2.58 2.81 2.92 2.94 .4120.5600.6730.226 .330 .330 .16 .19 .20 .055 .066 .066 .11 .12 .14 .046.046.046.98 .98 .98 .69 .88 1.00 .368 .487 .500 .498 .617 .630 .203 .297 .297 .192 .281 .281 JJJ.625 .625 .625 RSE.7500-16UNJF-3B .8750-14UNJF-3B 1.06

11、25-12UNJF-3B .485 .485 .485 3.02 3.09 3.34 3.47 3.53 3.63 .5600.6730.8100.330 .410 .410 .19 .20 .23 .066 .066 .066 .12 .14 .16 .046.046.0461.10 1.10 1.10 .88 1.00 1.25 .487 .500 .586 .617 .630 .786 .297 .369 .369 .281 .349 .349 KKK.750 .750 .750 RSE.8750-14UNJF-3B 1.0625-12UNJF-3B 1.3125-12UNJ-3B .6

12、02 .602 .602 3.98 4.04 4.15 4.47 4.60 4.94 .6730.81001.0620.410 .510 .510 .20 .23 .30 .066 .066 .066 .14 .16 .21 .046.046.0461.40 1.40 1.40 1.00 1.25 1.50 .500 .586 .631 .630 .786 .831 .369 .459 .459 .349 .434 .434 MM1.000 1.000 RS1.0625-12UNJF-3B 1.3125-12UNJ-3B .852 .852 4.49 4.61 5.50 5.53 .81001

13、.0620.510 .750 .23 .30 .066 .066 .16 .21 .046.0461.80 1.80 1.25 1.50 .586 .631 .786 .831 .459 .675 .434 .638 TABLE 2 - HOSE OR SLEEVE OUTSIDE DIAMETERS /10/ (DIAMETERS ARE MAXIMUM UNLESS OTHERWISE NOTED) SLEEVECODE SLEEVEMATERIAL TEMPLIMITF SIZE.250SIZE.375SIZE.500SIZE.625SIZE.750SIZE1.000 - (-) IND

14、ICATES HOSE ONLY NO SLEEVE (REF) 275 .420-.590 .525-.760 .750-.925 .870-.985 .980-1.180 1.264-1.580G FIRESLEEVE (AS1072 SIL-FG) (5 MIN) /11/ /12/ /13/ 275 .970 1.150 1.380 1.500 1.750 2.000 F ABRASION SLEEVE SHRINK-ON (POLYOLEFIN AS1073-CODE B) /18/275 .650 .830 .990 1.060 1.260 1.670 K INTEGRAL ABR

15、ASION SLEEVE (BRAIDED) POLYESTER 275 .495-.685 .600-.855 .825-1.020 .945-1.080 1.055-1.275 1.339-1.675TABLE 3 - HOSE ASSEMBLY LENGTH TOLERANCES HOSE ASSEMBLY LENGTH TOLERANCE UNDER 18 in .125 in 18 TO 36 in EXCLUSIVE .250 in 36 TO 50 in EXCLUSIVE .500 in 50 in AND OVER 1% AEROSPACE STANDARD AS6014SH

16、EET 3 OF 5REV.AHOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, PARA ARAMID REINFORCED, 275 F, 4000 PSI MAX, FLARELESS, TITANIUM FITTINGS, STRAIGHT TO 45 DEGREE TABLE 4 - WEIGHTS /19/ HOSE OR SLEEVECODE HOSE, PART OR SLEEVE UNITS SIZE.250SIZE.375SIZE.500SIZE.625SIZE.750SIZE1.000 - HOSE ONLY LB/IN .010 .014 .

17、020 .033 .032 .055 G FIRESLEEVE AS1072 (5 min PER AS1055) LB/IN .016 .019 .028 .029 .037 .041 F PROTECTIVE SLEEVE, SHRINK-ON (POLYOLEFIN AS1073, CODE B) /18/ LB/IN .002 .003 .003 .003 .005 .007 NONE FIRESLEEVE CLAMP LB/EA .019 .019 .019 .024 .024 .020 NONE FITTING END (STRAIGHT) /14/ R S ELB/EALB/EA

18、LB/EA- .057.068.091.102.127.137.162.188.221.247.300.539.592.6381.038 1.084 - NONE FITTING END (45 DEGREE) /14/ R S ELB/EALB/EALB/EA- .069.091.112.123.155.165.189.230.261.266.406.633.684.8491.230 1.273 K ABRASION SLEEVE POLYESTER WITH HOSE LB/IN .013 .017 .023 .026 .035 .058 TABLE 5 - CUFF LENGTH HOS

19、E SIZE LENGTH (INCHES) .25 .250 2.50 .375 3.00 .500 3.75 .625 4.50 .750 5.50 1.00 6.75 NOTES: 1. MATERIALS: A. HOSE AND FITTINGS - PER AS5951. B. THE COLLARS MAY BE STAINLESS STEEL. C. SLEEVES - SEE APPLICABLE STANDARDS, TABLE 2. /2/ PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED AND A

20、SSEMBLED BY AN ACCREDITED MANUFAACTURER OR ASSEMBLED BY AN ACCREDITED DISTRIBUTOR LISTED ON THE PRI-QPL-AS5951 FOR THIS STANDARD. SEE http:/ FOR CURRENT QPL ONLINE. 3. CONSTRUCTION AND PERFORMANCE PER AS5951. FITTINGS SHALL BE PERMANENTLY ATTACHED TO HOSE. 4. OPERATING CHARACTERISTICS PER AS5951 EXC

21、EPT FOR USE IN HYDRAULIC SYSTEMS UP TO 4000 PSI BASED ON SWIVEL NUT “T” THREAD. AEROSPACE STANDARD AS6014SHEET 4 OF 5REV.AHOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, PARA ARAMID REINFORCED, 275 F, 4000 PSI MAX, FLARELESS, TITANIUM FITTINGS, STRAIGHT TO 45 DEGREE /5/ MARKING: MARKING SHALL BE PER AS5951E

22、XCEPT OPERATING PRESSURE 4000 PSI MAX ON A STAINLESS STEEL BAND NOT OVER 1.0 IN WIDE OR ON THE COLLAR. IF A BAND IS USED, IT SHALL BE LOCATED OVER THE COLLAR. THE CHARACTERS SHALL BE A MINIMUM OF .06 IN HIGH. THE BAND SHALL BE SO DESIGNED AS TO REMAIN TIGHT ON THE COLLAR TO PREVENT RELATIVE MOVEMENT

23、 AND SHALL BE OF SUFFICIENT STRENGTH TO PREVENT REMOVAL BY HAND. MARKING BAND SHALL BE COVERED WITH TRANSPARENT POLYOLEFIN SHRINK SLEEVE PER AS1073 CODE A. /6/ HOSE LENGTH: LENGTH “L” IS A FOUR DIGIT NUMBER OF WHICH THE FIRST THREE DIGITS DESCRIBE THE HOSE ASSEMBLY LENGTH IN WHOLE INCHES, AND THE FO

24、URTH DIGIT, THE FRACTION OF AN INCH IN EIGHTHS. LENGTH “L” IS MEASURED FROM “GAGE DIAMETER” TO “GAGE DIAMETER”. FOR LENGTH TOLERANCES SEE TABLE 3. TO CONVERT “GAGE DIAMETER” TO “GAGE DIAMETER” TO “END TO END” MEASUREMENT, ADD D1 AND D3 TO LENGTH “L” FOR NAS1760 END STYLES OR D2 AND D4 TO LENGTH “L”

25、FOR AS4458 GLOBESEAL END STYLES. /7/ HOSE FITTING INSIDE DIAMETER SHALL BE VERIFIED BY PASSING THE DESIGNATED, OR LARGER, SPHERICAL BALL PER TABLE 1 THROUGH THE HOSE ASSEMBLY. /8/ DISTANCE ACROSS CORNERS OF COUPLING NUT, COLLAR OR NIPPLE MAY EXCEED THIS DIMENSION. /9/ FITTING ENDS MUST COMPLY WITH N

26、AS1760, AS4458 OR EQUIVALENT. DIMENSION D1 APPLIES TO NAS1760 AND D2 APPLIES TO AS4458. FITTINGS SHALL MATE WITH AS5863. COUPLING NUTS SHALL BE FUNCTIONAL EQUIVALENT TO AS4370 EXCEPT WIRE GROOVE. THREADS AND WIRE GROOVE IN NUT, RETAINER WIRE AND FITTING END WIRE GROOVE SHALL BE COATED WITH AS5272 TY

27、PE 1 SOLID FILM LUBRICANT. /10/ OUTSIDE DIAMETERS: DIAMETERS ARE LISTED FOR CLAMP SELECTION. TUBULAR SLEEVES MAY NOT BE A PERFECT ROUND AND SHALL BE MEASURED WITH A DIAMETER MEASUREMENT TAPE. /11/ SLEEVE DIAMETERS: THE TABLE 2 SLEEVE DIAMETERS FOR AS1072 SLEEVES APPLY WHEN THE SLEEVE IS COMPRESSED,

28、OR CLAMPED TO CONTACT THE HOSE, IN THIS CASE, A WRINKLE MAY OCCUR OVER APPROXIMATELY 10% OF THE SLEEVE CIRCUMFERENCE. /12/ FIRESLEEVE: THE CUT ENDS OF THE FIRESLEEVE SHALL BE COATED WITH RTV SILICONE RUBBER PRIOR TO INSTALLATION TO PREVENT WICKING OF FLUIDS. THE FIRESLEEVE ENDS SHALL BE SECURED TO T

29、HE HOSE ASSEMBLY END FITTINGS WITH CORROSION RESISTANT STEEL BANDS. AFTER INSTALLATION, CRACKS OR VOIDS IN THE FIRESLEEVE, WHICH EXPOSE THE FIBERGLASS, SHALL BE COATED WITH RTV SILICONE RUBBER. /13/ IDENTIFICATION MARKING: ADD “AS1055 TYPE IIB CLASS A-S/P” TO IDENTIFICATION MARKING TO SHOW LEVEL OF

30、COMPLIANCE, “FIRE RESISTANT 275 F (5 MIN), WITH AS1055.” /14/ JUMP SIZE CODE EXPLANATION: A. R-STEP DOWN 1 STANDARD LETTER SIZE PER TABLE 1 (REDUCED) B. S-HOSE SIZE (NO REDUCTION OR EXPANSION) C. E-STEP UP 1 STANDARD LETTER SIZE PER TABLE 1 (EXPANDED) NOTE: SPECIFY STRAIGHT FITTING SIZE FOLLOWED BY

31、THE ELBOW FITTING SIZE IN THE PART NUMBER. 15. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. /16/ SAFETY WIRE HOLES LOCATION AND DIAMETER PER AS1043 AS FOLLOWS: A. L = TWO OR THREE HOLES PER HEX SIZE PER AS1043 B. C = NO SAFETY WIRE HOLES AEROSPACE STANDARD AS6014SHEET 5 OF 5REV.AHOSE ASSEMBLY, PO

32、LYTETRAFLUOROETHYLENE, PARA ARAMID REINFORCED, 275 F, 4000 PSI MAX, FLARELESS, TITANIUM FITTINGS, STRAIGHT TO 45 DEGREE /17/ THIS PART STANDARD TAKES PRECEDENCE OVER AS5951 IN CASES OF CONFLICT. /18/ THE SHRINK-ON POLYOLEFIN SLEEVE SHALL COVER THE ENTIRE HOSE AND A MINIMUM OF 50% OF THE COLLARS ON B

33、OTH ENDS OF THE ASSEMBLY. /19/ FITTING WEIGHTS ARE REFERENCE AND BULK HOSE AND SLEEVE ARE MAXIMUM. /20/ THE INTEGRAL POLYESTER ABRASION SLEEVE, CODE K, SHALL HAVE A SUPPORT CUFF IN ACCORDANCE WITH FIGURE 2. THE CUFF MAY BE CONTOURED AND HAVE A MINIMUM THICKNESS OF .10 INCHES. THE CUFF SHALL BE ADHER

34、ED TO THE FITTING COLLAR/SOCKET AND HOSE. THE CUFF MATERIAL SHALL BE A SILICONE MATERIAL THAT IS COMPATIBLE WITH AIRCRAFT FLUIDS. 21 THE ACCEPTANCE TEST PROOF PRESSURE SHALL BE 8000 PSI. 22. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNI

35、CAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.23. EXAMPLE OF PART NUMBER: