NEMA C81 62-2017 Electric Lampholders.pdf

《NEMA C81 62-2017 Electric Lampholders.pdf》由会员分享，可在线阅读，更多相关《NEMA C81 62-2017 Electric Lampholders.pdf（78页珍藏版）》请在麦多课文档分享上搜索。

1、 2017 National Electrical Manufacturers Association ANSI C81.62-2017 American National Standard for Electric Lampholders Secretariat: National Electrical Manufacturers Association Approved : January 24, 2017 American National Standards Institute, Inc. 2017 National Electrical Manufacturers Associati

2、on NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person par

3、ticipating in the development of this document. American National Standards Institute, Inc. (ANSI) standards and guideline publications, of which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers a

4、nd/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA administers the process to promote fairness in the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completen

5、ess of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA disclaims liability for any personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly res

6、ulting from the publication, use of, application, or reliance on this document. NEMA disclaims and makes no guaranty or warranty, expressed or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document wi

7、ll fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the performance of any individual manufacturer or sellers products or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render profession

8、al or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in de

9、termining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no powe

10、r, nor does it undertake to police or enforce compliance with the contents of this document. NEMA does not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health- or safety-related information in

11、 this document shall not be attributable to NEMA and is solely the responsibility of the certifier or maker of the statement. ANSI C81.62-2017 Page i 2017 National Electrical Manufacturers Association American National Standard Approval of an American National Standard requires verification by the A

12、merican National Standards Institute, Inc. (ANSI) that the requirements for due process, consensus, and other criteria for approval have been met by the standards developer. An American National Standard implies a consensus of those substantially concerned with its scope and provisions. Consensus is

13、 established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly and materially affected interests. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objection

14、s be considered, and that a concerted effort be made toward their resolution. The existence of an American National Standard does not in any respect preclude anyone, whether s/he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures

15、not conforming to the standards. It is intended as a guide to aid the manufacturer, the consumer, and the general public. The American National Standards Institute, Inc., does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no pe

16、rson shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute, Inc. Requests for interpretations should be addressed to the Committee Secretariat referred to on the title page. CAUTION NOTICE: This American

17、 National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards

18、 by calling or writing the American National Standards Institute, Inc. Published by National Electrical Manufacturers Association 1300 North 17th Street, Suite 900, Rosslyn, Virginia 22209 2017 National Electrical Manufacturers Association. All rights, including translation into other languages, res

19、erved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the International and Pan American copyright conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the

20、 prior written permission of the publisher. Printed in the United States of America ANSI C81.62-2017 Page ii 2017 National Electrical Manufacturers Association Foreword (This foreword is not part of American National Standard C81.62.) In 1990 and 1991 the American National Standards (ANS) for lamp b

21、ases, lampholders and gauges were split into three separate standards to line up with the IEC format. ANSI C81.61, ANS for Electric Lamp Bases paralleled IEC 60061-1; ANSI C81.62, ANS for Lampholders for Electric Lamps paralleled IEC 60061-2 and ANSI C81.63, Gauges for Electric Lamp Bases and Lampho

22、lders paralleled IEC 60061-3. Also a fourth standard, ANSI C81.64 Guidelines for Electrical Lamp Bases, Lampholders and Gauges was published to parallel IEC 60061-4 in 1993. In 1996, the first IEC data sheets were adopted “as is“ as Nationally Acknowledged International Standards and published as Su

23、pplement g to the existing C81.61, 62 and 63 standards. Now many more (if not most) ANSI base standard sheets are IEC sheets adopted as ANSI standards. In 2003, a revision and consolidation of ANSI C81.62 was issued to include, first, a reference to all IEC lampholder standard sheets adopted as ANSI

24、 standards. Second, standard sheets for a small number of lampholders used mainly in North America or not harmonized with IEC were included in Part II. Part III contained any United States deviations to the IEC standard sheets, which had been adopted as Nationally Acknowledged International Standard

25、s as published in IEC 60061-2. Part IV contained an informative annex on first versus third angle projection and related standards. ANSI C81.62-2017 Page iii 2017 National Electrical Manufacturers Association CONTENTS Foreword ii Part I General Information and Requirements 1 1 Scope 1 2 Normative re

26、ferences 1 3 General Information 1 Table 1 ANSI and IEC Lamp Base (Cap) Standard Sheets 3 Part II ANSI Standard Sheets For Bases (Caps) For Electric Lamps 9 Part III United States Deviations to IEC Harmonized Electric Lamp Base Standard Sheets 70 Annexes Annex A Contrast of Projection Methods on Eng

27、ineering Drawings 71 Annex B Related Standards 72 ANSI C81.62-2017 Page iv 2017 National Electrical Manufacturers Association ANSI C81.62-2017 Page 1 2017 National Electrical Manufacturers Association PART I General Information and Requirements 1 Scope This standard sets forth the specifications for

28、 lampholders for electric lamps. 1.1 Important Patent Disclaimer It is possible that some of the elements of this document may be the subject of patent rights. When this document was approved for publication, ANSLG did not know of any patent applications, patents pending, or existing patents. ANSLG

29、shall not be held responsible for identifying any or all such patent rights. 2 Normative References The following publications contain provisions, which, through reference in this text, constitute provisions of this American national Standard. At the time of publication, the editions indicated were

30、valid. All standards are subject to revision, and parties to agreements based on this American National Standard are encouraged to investigate the possibility of applying the most recent editions of the publications indicated below. ANSI C81.61-2009, Specifications for Bases (Caps) for Electric Lamp

31、s ANSI C81.63-2009, Gauges for Electric Lamp Bases and Lampholders IEC 60061, Lamp caps and holders together with gauges for the control of interchangeability and safety: Part 1: Caps IEC 60061-1 Ed. 3 including Amendment 39-2007 Part 2: Lampholders IEC 60061-2 Ed. 3 including Amendment 36-2007 Part

32、 3: Gauges IEC 60061-3 Ed. 3 including Amendment 38-2007 UL 496-2004, Edison-Base Lampholders UL 542-1999, Lampholders, Starters, and Starter Holders for Fluorescent Lamps 3 General information Two types of lampholder standard sheets are identified in this standard, and both are listed in Table 1, A

33、NSI and IEC Lampholder Standard Sheets. All lampholder types are listed in color to indicate their applications: Blue for automotive and miniature; green for general lighting service including common Edison screw lampholders; red for fluorescent; and black for miscellaneous. For some lampholders eit

34、her no international standard exists or the international standard is not acceptable at this time. For such lampholders an ANSI standard sheet is included. These standard sheets are identified in Table 1ANSI and IEC Lampholder Standard Sheets under the column heading “ANSI C81.62“. These Standard Sh

35、eets are found in Part II. ANSI C81.62-2017 Page 2 2017 National Electrical Manufacturers Association Certain standard sheets from IEC standard 60061-1 Lamp caps and holders together with gauges for the control of the interchangeability and safety, Part 2: Lampholders, and its supplements, have been

36、 adopted as Nationally Acknowledged International Standards and constitute part of the American National Standard for Lampholders. The standard sheets for these lampholders are not included, but are identified in Table IANSI and IEC Lampholder Standard Sheets under the column heading “IEC 60061-2“.

37、If there are any United States deviations from these IEC standard sheets; the sheet number is marked with a footnote and the deviations are found in Part III. These IEC standards are available from: American National Standards Institute Attn: “eStandard Store” 25 West 42ndStreet, 4thFloor New York,

38、NY 10036 Or by calling 212 642-4900 during normal business hours. They may also be purchased electronically at the following URL www.ansi.org or http:/webstore.ansi.org/ansidocstore/default.asp The drawings on the internationally standardized (IEC) sheets are in first angle projection rather than th

39、e third angle commonly used in the North American (ANSI) approved standard sheets. Annex A explains the difference between the two systems. In addition, the common American term “Base“ is internationally known as “Cap“. Internationally the decimal point (.) is not used in dimensions, rather a comma

40、(,) separates a decimal number e.g. 4,5 rather than 4.5. However, in the designation of a fit the decimal point is used e.g. GY6.35. This Standard is used in conjunction with ANSI C81.61, Bases (Caps) for Electric Lamps; ANSI C81.63, Gauges for Bases and Lampholders for Electric Lamps and IEC 60061,

41、 Lamp caps and holders together with gauges for the control of interchangeability and safety, Part 1: Caps, and Part 3: Gauges. In addition the safety requirements for Edison screw lampholders are found in UL 496, Edison-Base Lampholders and the safety requirements for fluorescent lamp bases and sta

42、rter holders are found in UL 542, Lampholders, Starters, and Starter Holders for Fluorescent Lamps. ANSI C81.62-2017 Page 3 2017 National Electrical Manufacturers Association Table 1 ANSI and IEC Lampholder Standard Sheets System Description Standard Sheets IEC 60061-2 ANSIC81.62 Bayonet lampholders

43、 B/BX8.4d Holder 7005-140-1 BA9/12.5 Miniature bayonet lampholder 2-10-3 BAW9s HY21w Lampholder 7005-149-1 BAZ9s HY6w Lampholder 7005-150-1 BA15s, BA15d Candelabra single and double-contact bayonet 2-20-2 BAY15s, BAY15d Single- and double contact bayonet for offset pins 2-20-2 BAZ15d Double contact

44、bayonet for offset and non-aligned pins 2-20-2 BY22d Multipurpose sleeved double-contact bayonet 7005-17-5 Edison screw lampholders E5 Midget screw lampholder 7005-20-5 E10 Miniature screw 7005-20-5 E11 Mini-candelabra screw 7005-6-1 E12 Candelabra screw 7005-28-1 E17 Intermediate screw 7005-20-5 E2

45、6/24 Single-contact medium screw 7005-21A-1 Edison threads Thread length and top of thread to center contact dimensions for E5, E10, E17, and E26 lampholders 7005-20-5 E26d Double-contact medium screw 7005-29-2 E26/50x39 Skirted medium screw for PAR lamps 7005-21A-1 E26/53x39 Extended skirted medium

46、 screw for R- lamps 7005-21A-1 EX26 Single-contact medium screw with extended insulation 2-911-1 E39 Single-contact mogul screw 7005-24A-3 E39d Double-contact mogul screw 2-187-1 EP39 Position-oriented mogul screw 2-202-2 EX39 Exclusionary mogul screw for HID lamps 2-210-2 Single pin lampholders Fc2

47、 HID slide side contact lampholder 7005-114-1 Fa8 Fluorescent single-pin 7005-58-1 ANSI C81.62-2017 Page 4 2017 National Electrical Manufacturers Association Table 1 ANSI and IEC Lampholder Standard Sheets System Description Standard Sheets IEC 60061-2 ANSI C81.62 Multiple pin lampholders and connec

48、tors G4 Two-pin lampholder for single ended TH (tungsten halogen) GLS (general lighting service) lamps 7005-72-1 GU4 Two-pin lampholder for MR11 GLS lamps with retainer springs 7005-108-2 GZ4 Two-pin connector for MR11 projection lamps 7005-67-1 G5 Fluorescent miniature two-pin lampholder 2-310-3 G5

49、.3 Two-pin for single-ended TH (tungsten halogen) projection lamps 7005-73-1 GU5.3 Two-pin for MR16 GLS lamps with retainer springs 7005-109-2 GX5.3 Two-pin lampholder and connector for MR13 and low voltage MR16 projection lamps 7005-73A-5 GY5.3 Two-pin lampholder for high voltage MR16 projection lamps 7005-73B-4 7005-73B-5 G/GX/GY6.35 Two-pin lampholders for single-ended TH GLS lamps 7005-59-2 GZ6.35 Two-pin connector for MR16 projection lamps 7005-59A-3 GU6.5 Two-pin turn and lock for metal halide lamps 7005-152-1 G6.6 Two-pin with an additional ground pin f