NAVY MIL-T-46632 B-1994 THRUSTER CARTRIDGE ACTUATED M2A2 METAL PARTS ASSEMBLY《M2A2金属零件集合发动弹药筒推进器》.pdf

《NAVY MIL-T-46632 B-1994 THRUSTER CARTRIDGE ACTUATED M2A2 METAL PARTS ASSEMBLY《M2A2金属零件集合发动弹药筒推进器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-T-46632 B-1994 THRUSTER CARTRIDGE ACTUATED M2A2 METAL PARTS ASSEMBLY《M2A2金属零件集合发动弹药筒推进器》.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、HIL-T-46632B = 9999906 1985852 Tb5 INCH-POUND MlL-T-46632B(OS) 11 Augwst 1994 SUPERSEDING 20 August 1969 MIL-T-46632A0 MILITARY SPECIFICATION THRUSTER, CARTRIDGE ACTUATED, M2A2 METAL PARTS ASSEMBLY is specification is approved for use by the Naval Sea System Command, Department of the Navy, and is a

2、vailable for use by all Departments and Agencies of the Departments of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for the M2A2 Cartridge Actuated Thruster Metal Parts Assembly (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards

3、. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplements thereto, cited

4、 in the solicitation (see 6.2). SPECIFICATIONS MILITARY MIL-A-2550 Ammunition, General Specification For STANDARDS MILITARY MIL-STD-105 MIL-STD-109 MIL-STD-4 13 Sampling Procedures And Tables For Inspection By Attributes Quality Assurance Terms And Definitions Visual Inspection Guide for Elastomeric

5、 O-rings Beneficial comments (recommendations, additions, deletions) ad any pertinent data which may be of use in improving this documen should be ddressed to: Coder, Mian Head Division, Naval Surface Warfare Center, Standardization Branch (Code 8420), 101 Strauss Avenue, Indian Head, MD 20640-5035,

6、 by using the Standardization Document Improvement Proposal D Form 1426) appearing at the end of this document or by sending a letter. AMSC N/A FSC 1377 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permit

7、ted without license from IHS-,-,-NIL-T-4bb32B 9999906 1985853 9TL (Unless otherwise indicated, copies of federai and military specifications and standards are available from Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 191 1 1-5094.) 2.1.2 Other Government doc

8、uments, drawings, and publications. The following Government drawings form a part of this specification to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation (see 6.2). DRAWINGS Naval Surface Warfare Center, Indian Head (CAGE Codes 19200 and 19203

9、) 8593874 Thruster, Cartridge Actuated, M2A2 Metal Parts Assembly 8797633 Box, Fiberboard (Inner), Packing, Ammunition, For Thruster, Cartridge Actuated, M2A2 8 7 9 7 6 3 4 Box, Packing, Ammunition, For Thruster, Cartridge Actuated, M2A2 - 9235819 Box, Fiberboard (Outer), Alternative, Packing Ammuni

10、tion, for Thruster, Cartridge Actuated, M2A2 U.S. Air Force TPO 00-921-5048 Thruster, Cartridge Actuated, M2A2 (Application for copies should be addressed to: Commander, Indian Head Division, Naval Surface Warfare Center, Attn: Data Control Branch (Code 8410), Indian Head, MD 20640-5035.) 2.2 Order

11、of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Fi

12、rst article. When specified in the contract or purchase order (see 6.2), a sample shall be subjected to the first article inspection (see 4.4 and 6.3). 3.2 Materials. All materiais used in the manufacture of the thrusters shall conform to the specifications referred to on the respective drawings unl

13、ess specific approval in writing covering a departure therefrom has been obtained from the cognizant Navy design activity prior to manufacture. When alternate materials or methods of manufacture are specified on the drawings, the bidders selections shall be clearly stated in the proposal. 3.2.1 Raw

14、material. The contractor shall be responsible for selecting from the classification list contained in the raw material specification the surface and physical condition of the raw material intended for use in manufacture. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without

15、license from IHS-,-,-MIL-T-4bb32B 999990b 1985854 838 3.3 Hardness and other physical properties. Hardness and other physical properties required by the drawing shall be uniform throughout the part within specified tolerances. Requirements for all alloy steel parts shall be achieved by quenching and

16、 tempering. 3.4 Hydrostatic pressure. The body and head shall withstand a hydrostatic pressure of 10,ooO pounds per square inch (psi) for 15 seconds, minimum, without leaking, deformation, or mechanical failure (see 6.4.1). 3.5 Torque. 3.5.1 Assembly torque. The body and holding rings shall be assem

17、bled hand tight. A torque of 100 + 20 inch pounds shall then be applied between the body and holding ring for the purpose of tightening the assembly prior to spotting threads for setscrew installation. 3.5.2 Breakaway torque. The body with respect to the holding ring shall withstand a breakaway torq

18、ue application of 400 inch pounds, minimum, without any movement or deformation. 3.6 Structural strength. The assembled thruster shall withstand a static tensile force of 2,000 pounds, minimum, for 15 seconds, minimum, between mounting points without unlocking and without mechanical failure (see 6.4

19、.1). 3.7 Shear pin strength. The shear pin, after application of protective finish, shall shear when a load of 55 k 4 pounds is applied at the steady rate of 0.125 inch per minute. 3.8 Metal parts assembly. Parts shall be combined to produce an assembly which conforms to the requirements of the meta

20、l parts assembly drawing and the requirements of 3.8.1 through 3.8.3. 3.8.1 Head and body. The head and body shall be assembled hand tight. 3.8.2 Piston locking spring and end sleeve. The piston locking spring shall enter the spring hole in the piston without any bending along its entire length. The

21、 assembly of the piston locking spring to the end sleeve, with the cap screw and washer, shall be hand tight. If axial misalignment of the piston locking spring occurs upon completion of assembly, it will be permissible to back off the cap screw sufficiently to eliminate axial misalignment of the pi

22、ston locking spring. 3.8.3 End sleeve rotation. Upon completion of assembly and after the structural strength test, the end sleeve shall be free to rotate 360 degrees in a clockwise direction. 3.9 Protective finish. Protective finish shall be in accordance with the applicable specifications and shal

23、l apply to all surfaces of the component regardless of contour configuration. 3.10 Residual magnetism. The metal parts assembly shall not deflect the indicator of the compass more than five degrees in either direction using procedures in 4.6.7. 3.11 Workmanship. Thrusters shall be free of cracks, sp

24、lits, or other defects which might prevent proper mating with connecting parts or proper functioning of the device. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-46632B M 9999906 1985855 774 M 3.11.1 Metal defects. All components shall be f

25、ree from cracks, splits, cold shuts, inclusions, porosity, or any similar defect. 3.11.2 Burr. No part shall have a burr which might interfere with the assembly or function of the item or which might be injurious to personnel handling the item. 3.11.3 Foreign matter. No part or assembly shall contai

26、n chips, dirt, grease, rust, corrosion, or other foreign matter. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of ail inspection requirements (examinations and tests)

27、as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perfor

28、m any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements (see 6.2). 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth

29、in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for

30、acceptance comply with ail requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements; however, this does not authorize submission of known defective material, either indicated or actual, nor does it comm

31、it the Government to acceptance of defective material. 4.1.2 Quality assurance terms and definitions. Reference shall be made to MIL-STD-109 to define the quality assurance terms used. 4.1.3 Inspections. Inspections shall be in accordance with MIL-A-2550. 4.2 Classification of inspections. The inspe

32、ction requirements specified herein are classified as follows: a. b. First article inspection (see 4.4) Quality conformance inspection (see 4.5) 4.3 Inspection conditions. Unless otherwise specified (see 6.2), all inspections shall be performed under the following conditions: a. Temperature: room am

33、bient (68 to 77F) b. Altitude: sea level c. Humidity: 50 percent relative, maximum d. Atmospheric pressure: 14.7 psi 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-46632B m 9999906 1985856 600 = 4.4 First article inspection. At the beginning

34、 of regular production, the contractor shall submit an initial production sample to a Government approved facility for evaluation. The sample shall consist of five metal parts assemblies, nine sets of unassembled parts, one set of unassembled parts without plating or final protective finish, and fif

35、ty shear pins from the same lot of shear pins tested by the contractor. The sample shall be manufactured in the same manner, using the same materiais, equipment, processes, and procedures as used in regular production. All parts and materials, including packaging and packing, must be the same as wil

36、l be used for regular production and shall be obtained from the same source of supply. After inspection and provisional acceptance at source, the first article sample shall be inspected for all requirements of the drawings and specifications. The Government reserves the right to require new first ar

37、ticle samples until an acceptable sample is submitted (see 6.3). 4.5 Quality conformance inspection. 4.5.1 Lot. 4.5.1.1 Submission of product. Unless otherwise specified by the contracting activity, formation and identification of lots shall be in accordance with MIL-STD-105. . 4.5.1.2 Size of lot.

38、The production lot size shall be as specified in the contract. 4.5.2 Examination. One hundred percent examination shall be performed for all critical defects. Examination for major and minor defects shall be performed on a defect basis in accordance with the classification of defects. Four power (4x

39、) magnification may be used in performing visual examination for such defects as burr and foreign matter. Inspection for rubber O-rings shall be in accordance with MIL-STD-413. When compliance with the applicable requirement is in doubt as a result of visual examination, the characteristic shall be

40、measured or gaged to determine acceptability. Ali nonconforming material shall be rejected. 4.5.2.1 Key, Drawing 8593857, covering a detail of Drawing 8593814. Characteristics Defect Method of Inspection Critical None defined Major 101 102 103 104 105 106 107 Radial profile of length, inside and out

41、side Radial profile of width Metal defective Protective finish inadequate or defective Surface finish improper Burr or sharp corner Foreign matter Gage Gage Visual Visual Visual Visual Visual 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-fl1-T-g6

42、&32B = 9999906 1985857 547 MIL-T-46632B(OS) Minor 20 1 Total length 202 Radii incorrect, except as otherwise classified 4.5.2.2 Trunnion, Drawing 8593860, covering a detail of Drawing 8593874. Critical None defined Major 101 102 103 104 105 106 107 108 109 110 111 112 Minor 20 1 202 203 204 205 206

43、207 208 209 210 211 Concentricity of lugs Symmetry of lugs wit. inside Symmetry of flats at root of lugs with inside Symmetry of lugs with sides Perpendicularity of sides with inside Diameter of lugs, min Width Width across flats, min Thickness of wall, min Radius at base of lugs incorrect Metai def

44、ective Protective finish inadequate or defective Diameter of lugs, max Diameter, inside Length of lugs Width across flats, max Thickness of wail, max Location of lugs Marking missing, incorrect, or illegible Radius or chamfer incorrect, except as otherwise classified Surface finish improper Burr or

45、sharp corner Foreign matter Gage Gage Gage Gage Gage Gage Gage Gage Gage Gage Gage Gage Visual Visual Gage Gage Gage Gage Gage Gage Visual Gage Visual Visual Visual 4.5.2.3 Plug, Piston, Drawing 8593868, covering a detail of Drawing 8593874. Critical None defined Major 101 102 Minor 20 1 202 Diamete

46、r Metal defective Thickness Chamfer incorrect Gage Visual Gage Gage 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-Ybb32B 9999Ob L98.5858 483 203 204 205 206 Protective finish inadequate or defective Surface finish improper Burr or sharp cor

47、ner Foreign matter Visual Visual Visual Visual 4.5.2.4 Sleeve, End, Drawing 8593869, covering a detail of Drawing 8593874. Critical None defined Major 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 Minor 20 1 202 203 204 205 206 207 208 209 210 21 1 212 213 214 215 216 217 218 2 19

48、Pitch diameter of external thread, min Major diameter of external thread, min Concentricity of cavity with body Concentricity of shoulder with body Symmetry of elongated slots with body Diameter of body, min Diameter of cavity, max Diameter of shoulder, min Width of slots Location of slots Radius of

49、 thread end Thread damaged or not full Metal defective Protective finish inadequate or defective Burr or sharp corner Foreign matter Pitch diameter of external thread, max Pitch diameter of internal thread Minor diameter of internal thread, rnax Diameter of body, max Diameter of cavity, min Diameter of shoulder, rnax Diameter of flange Diameter of thread undercut, min Length of slot Variation in alignment, flange face with face of cavity seat Depth of effective