NAVY MIL-M-82376 B-1990 MANUALS TECHNICAL OPERATION AND MAINTENANCE INSTRUCTIONS FOR TRAINING DEVICES《训练器材操作和维修指令的技术手册》.pdf

《NAVY MIL-M-82376 B-1990 MANUALS TECHNICAL OPERATION AND MAINTENANCE INSTRUCTIONS FOR TRAINING DEVICES《训练器材操作和维修指令的技术手册》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-M-82376 B-1990 MANUALS TECHNICAL OPERATION AND MAINTENANCE INSTRUCTIONS FOR TRAINING DEVICES《训练器材操作和维修指令的技术手册》.pdf（124页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-M-237bB TM W 9999906 O435227 5 MIL-M-82376B 30 MARCH 1990 SUPERSEDING 1 September 1977 MIL-M-82376A MILITARY SPECIFICATION MANUALS, TECHNICAL: OPERATION AND MAINTENANCE INSTRUCTIONS FOR TRAINING DEVICES This specification is approved for use by all Departments and Agencies of the Department of D

2、efense. 1. SCOPE, This document sets forth the detailed scope and contents requirements for the preparation of technical manuals for training devices. 1.1 Paragraphs with limited applicability. This document contains paragraphs which are not,applicable to all services. prefixed to indicate the servi

3、ces to which they pertain: (A) for Army, (N) for Navy and Marine Corps, and (F).for Air Force. Such paragraphs are 1.2 Table and figures, - All tables and figures used in this document are for example only. 2. APPLICABLE DOCUMENTS 2.1 Government documents. Beneficial comments (recommendations, addit

4、ions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Naval Training Systems Center, Code 4323, 12350 Research Parkway, Orlando, FL 32826-3224 , by using the self addressed Standardization Document Iinproveiiienc Proposal (DD Form 1426) appear

5、ing at the end of this document or hv letter. AMSC N4914 TMS C DISTRIBUTION STATEMENT A - Approved for public release; distribution is . unlimited, 0023E Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-8237bB TM m 777770b 0435228 7 m MIL-M-8237

6、6B 2.1.1 Soecifications. standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifi

7、cations and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS MILITARY MIL-M-7298 MIL-M-38784 Manuals, Commercial Off-the-shelf Manuals, Technical: General Style and Format Requirements MIL-M-38807 MIL-M-63004 MIL-M-63036 MIL-M-63038 MIL-M-63042 MIL-M-85337 MIL-P-3

8、8790 STANDARDS MILITARY DOD-STD-100 MIL-STD-12 Manuals, Technical, Illustrated Parts Breakdown, Preparation of Manuals, Technical, Preparation of Lubrication Orders Manuals, Technical, Preparation of Operation Manual, Technical, Unit or Aviation Unit, Direct Support or Aviation Intermediate and Gene

9、ral Support; Requirements for Manuals, Technical: Procedures for Destruction of Equipment to Prevent Enemy Use Manual, Technical: Quality Assurance Programs; requirements for Printing Production of Technical Manuals: General Requirements for - Engineering Drawing Practices - Abbreviations for Use on

10、 Drawings, Specifications, Standards, and in Technical Documents T II 0023E 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c I F e I MIL-M-823766 TM m 7777706 0435227 7 m I MIL-M-82376B MIL-STD-335 (TM) - Manual, Technical: Repair Parts and Specia

11、l Tools List MIL-STD-1379 - Military Training Program 2.1.2 Other Government documents. drawinas. and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. the issues shall be those cited in the solicitation. U

12、nless otherwise specified, DEPARTMENT OF THE ARMY AR 750-1 - Army Materiel Maintenance Concepts and Policies AR 750-43 - Test, Measurement, Diagnostic Equipment (TMDE) DA PAM 700-21 - The Army test, Measurement, and Diagnostic Equipment Register Index and Instructions: Part 1; Nomenclature Index, Na

13、tional Stack Number Index DA PAM 700-21-1 - The Army Test, Measurement, and Diagnostic Equipment Register Index and Instruction: Part 2; Functional Index; TMDE Summary of General Purpose Equipment DA PAM 738-750 - The Army Maintenance Management System (TAMMS) . DEPARTMENT OF THE AIR FORCE AFR 51-6

14、- Flying Training Certification Program T.O. 00-25-234 - General Shop Practice Requirements for the Repair, Maintenance, and Test of Electronic Equipment DEPARTMENT OF DEFENSE DLSC H4-1 DLSC H4-2 - Commercial and Government Entity (CAGE), United States and Canada, Nkne to Code - Commercial and Gover

15、nment Entity (CAGE), United States and Canada, Code to Name 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLSC H6-1 MIL-M-8237bB Til = 777770b 0435230 5 MIL-M-82376B Section C, Part 1 of Federal Item Identification Guides for Supply Cataloging, A

16、bbreviations, and Symbols (Unless otherwise indicated, copies of Federal and Military Specifications, Standards, and Handbooks are available from the Naval Publications and Forms Center, (Attention: NPODS), Building 4D, 700 Robbins Ave., Philadelphia, PA 19111-5094.) i 2.2 Non-Government wblications

17、. The following documents form a part of this specification to the extent specified herein. specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. otherwise specified, the issues of documents not listed in the DODI

18、SS are the issues of documents cited in the solicitation. Unless otherwise Unless ANSI x3.5 - Flow Chart Symbols for Information Processing ANSI Y14.15 - Electrical and Electronic Diagrams ANSI Y32.2 - Graphic Symbols for Electrical and Electronic Diagrams ANSI Y32.10 - Graphic Symbols for Fluid Pow

19、er Diagrams ANSI Y32.14 - Graphic Symbols for Logic Diagrams ANSI Y32.16 - Reference Designations for Electrical and Electronic Parts and Equipment (Application for copies should be addressed to the United States of America National Standards Institute, Inc., 1430 Broadway, New York, NY 10018.) 2.3

20、Order of precedence. In the event of a conflict between the text of this document and the references cited herein (except for related associated detail specifications, specification sheets or military standards), the text of this document shall take precedence, Nothing in this document, however, sha

21、ll supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 General requirement. The general style and format shall be in accordance with this document and MIL-M-38784. in accordance with the MIL-P-38790. Printing requirements shall be 3.11 Armv te

22、chnical manuals. (A) When directed by the contracting activity (see 6.9), technical manuals for Army training devices shall be prepared in accordance with Appendix A. 0023E 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-823766 Til m 944970h

23、0435231 7 m MIL-M-82376B 3.1.2 Device utilization handbook. (N) When directed by the contracting activity, Device Utilization Handbook shall be prepared in accordance with Appendix B. also apply to Appendix B. The general requirements of this specification and MIL-M-38784 3.1.3 Securitv classificati

24、on markings. Security classification markings for technical manuals shall be in accordance with MIL-M-38784. 3.1.4 Contractor loPistic - sumort. (F) For those systems converting to Contractor Logistic Support (CLS), technical manuals shall be prepared in accordance with MIL-M-7298, MIL-M-38784 and a

25、ppropriate technical manuals. 3.1.5 General content. Technical manuals shall be (1) designed and written to facilitate their use in maintenance, operation, repair, and logistic support; and (2) written to cover the Governments maintenance concept for the training device. 3.1.6 General arrangement. T

26、echnical manuals shall be arranged in volumes; shall be numbered by adding a dash and consecutive Arabic numbers after the assigned publication number, e.g., P-XXXX-1, P-XXXX-2, etc. The technical manuals may further be divided into parts, e.g., Volume I, Part 1; Volume II, Part 2 with covers and ta

27、ble of contents for each volume and part. Each new section of the tech.nica1 manual shall begin on a right-hand page. 3.1.7 Conflict between documents. When a conflict exists between the contract and this document, the contract shall take precedence. When a conflict exists between the requirements o

28、f this document and its referenced documents, this document shall take precedence. 3.1.8 Commercial-Off-The-Shelf (COTS) manuals. COTS manuals shall provide operation, maintenance and repair parts data for COTS equipment. COTS manuals shall conform to the requirements of MIL-M-7298. supplemental dat

29、a, the contractor shall prepare the needed information in accordance with MIL-M-7298 and meet the requirements of the cited specifications. Equipment for which the use of COTS manuals is permitted shall be covered as “black boxes“ in the basic technical manual with all input, output and interface da

30、ta depicted on all appropriate diagrams. individual COTS manual shall reflect the exact configuration of the delivered hardware identified by serial and model number(s). shall have been incorporated into the manuals prior to delivery to the Government. If the manual requires Each All applicable revi

31、sions 3.1.8.1 CoDvrights/rights in data. Copyrights/rights in data release information regarding COTS manuals shall be in accordance with MIL-M-7298. 3.1.9 Level of writinq. The level of writing shall be in accordance with MIL-M-38784 and to that of a technician having previous maintenance experienc

32、e with similar or related equipment. 0023E 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-82376B 3.1.9.1 (N) Unless otherwise directed by the contracting activity, the contractor shall provide documentation for Trainer Unique Equipment (TUE)

33、 that would permit maintenance to be performed to the Intermediate (piece-part) level of repair. specifically for the training device and is not commercially available off-the-shelf. TUE is defined as equi.pment that is contractor developed 3.2 Reference to other publications. Reference to other pub

34、lications shall be made as provided for in MIL-M-38784. Reference shall not be made to a portion of another publication which requires still further reference to a third publication. b 3.3 Twes of technical manuals. This specification covers the following L types of technical manuals: a. Operation a

35、nd Maintenance Manual (see 3.3.1). b. Systems Operation and Maintenance Manual (see 3.3.2). c. Systems Interface Manual (see 3.3.3). d. Manuals, Technical: Requirements for Army Training Devices (Appendix A). e. Handbook: Device Utilization for Navy Training Devices (Appendix B) * 3.3.1 Operation an

36、d maintenance manual. (N, F) The operation and maintenance manual shall contain the following sections: a. Front Matter (see 3.3.1.1). b. Section I - Description and Leading Particulars (see 3.3.1.2). c. Section II - Installation (see 3.3.1.3). d. Section III - Operation (see 3.3.1.4). e. f. Section

37、 V - Maintenance (see 3.3.1.6), g. Section VI - Maintenance Diagrams (see 3.3.1.7). h. Section VI1 - Illustrated Parts Breakdown/Repair Parts and Special Section IV - Theory of Operation (see 3.3.1.5). Tools List/Parts Catalog (see 3.3.1.8). i. Appendix(es) (see 3.3.1.9). j. Glossary (see 3.3.1.10).

38、 0023E 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-M-8237bB Til m 77777Ob Oq35233 O m 0023E 7 MIL-M-82376B k. Index (see 3.3.1.11). 3.3.1.1 Front matter. Front matter shall be in accordance with MIL-M-38784. 3.3.1.1.1 Foreword. (N) The fore

39、word, in addition to complying with MIL-M-38784, shall: a. Contain safety statements describing precautionary items applicable to the training device. b. Identify the operational system represented by the training device. c. Explain that coverage in the technical manual(s) is limited to TUE items or

40、 functions and that reference must be made to the applicable COTS or tactical technical manuals for additional information. d. List, in tabular form, all related contractor developed and COTS manuals by number and title which affect the operation and maintenance procedures of the training device. 3.

41、3.1.1.2 Introduction. (F) The introduction shall, in addition to complying with MIL-M-38784, also list, in tabular form, all related publications. This list shall identify the technical manuals by number and title, which affect the operation, maintenance, and inspection procedures of the training de

42、vice. The introduction shall explain that coverage in the technical manual includes organizational and intermediate level maintenance of the training device items and functions, and that reference may be made to equipment publications for additional information. Unless special techniques or material

43、s are required, the introduction shall include a reference to T.O. 00-25-234 for instructions concerning procedures and specific materials to be utilized in soldering electronic equipment. particular information shall be placed in section I of the technical manual. Descriptive and leading 3.3.1.2 Se

44、ction I - Description and leading Darticulars. The content of this section shall be such that command-level, supervisory personnel, and other users having an interest in the training device can easily and rapidly determine the purpose, physical and functional characteristics, and the operational cap

45、abilities of the training device. 3.3.1.2.1 Frontispiece. A frontispiece for the technical manual (usually a left-hand full page or a foldout, never back up) identified as page 1-0, figure 1-1 shall be prepared as a composite illustration of the separately housed units, sets, or subsystems of the co

46、mplete training device, giving proper nomenclature of the components indexed and captioned in accordance with the requirements of MIL-M-38784. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-82376B 3.3.1.2.2 Administrative reauirements. (A) Adm

47、inistrative requirements shall be provided as specified: a. Maintenance forms and records. (A) Maintenance forms, records, . and reports which are to be used by maintenance personnel at all maintenance levels are listed in and prescribed by DA PAM 738-750. b. Destruction of Army materiel to prevent

48、enemy use. (A) Destruction of Army materiel to prevent enemy use shall be in accordance with MIL-M-63042. c. Administrative storage. (A) Administrative storage requirements shall be included in the unit maintenance manual. These requirements shall be furnished by the contracting activity and shall r

49、eflect the requirements of AR 750-1. 3.3.1.2.3 Reporting of errors, Reports of errors, omissions, and recommendations for improving manuals shall be submitted on the appropriate form and forwarded to the command issuing the manual. furnished. A reply will be 3.3.1.2.4 DeSCriDtiOn. A description, in nontechnical, easily understood terms, shall be provided to include the following: a. The purpose of the training device. b. Scope of operation. c. H