NAVY MIL-I-60512 A-1990 INITIATOR CARTRIDGE ACTUATED DELAY M72 ASSEMBLY《 M72火药驱动起始延迟装置》.pdf

《NAVY MIL-I-60512 A-1990 INITIATOR CARTRIDGE ACTUATED DELAY M72 ASSEMBLY《 M72火药驱动起始延迟装置》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-I-60512 A-1990 INITIATOR CARTRIDGE ACTUATED DELAY M72 ASSEMBLY《 M72火药驱动起始延迟装置》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUND I i INITIATOR, C. MILITARY SPECIFICATION RTRIDGE ACIZTATED, DELA7 This specification is appmved for use by all Departments and Agencies of the Department of Defense. 1, SCOPE 1.1 Scope. This specification covers the requirements for the M72 Delay Cartridge Actuated Initiator Assembly (se

2、e 6.1). 2. APPLICABLE DOCUMEm 2.1, Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in t

3、he issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS t MIL-I-6051SA 30 March 1990 SUPERSEDING 20 June 1966 - AMENDMENT 2 12 September 1973 MIL-I-605E(MU) MILITARY MIL-A-2550 MIL,-1-14857 t M72

4、 ASSEMBLY MIL-1-60296 STANDAWS MILITARY MIL-STD-105 MIL-STD-109 MIL-STD-453 MIL-STD-1168 MS28741 Ammunition, General Specification For Initiator, Cartridge Actuated, Delay, M10, M31, M42, M72, and Ml14 Remanufactured Metal Parts Assembly Initiator, Cartridge Actuated, Delay, M10, M31, M42, M72, and

5、M114 Metal Parts Assembly Sampling Procedures and Tables for Inspection by Attributes Quality Assurance Terms and Definitions Inspection, Radiographic Ammunition Lot Numbering Hose Assembly, Detachable End Fitting, Medium Pressure AMSC N/A FSC 1377 DISIJFPHBWION STAmMEN“ A. Approved for public relea

6、se; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-b0532A 13 m 7777906 0425532 7 m MIL-I-60512A (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from

7、Standardization Documents Order Desk, Bldg 44 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless other

8、- wise specified, the issues are those cited in the solicitation (see 6.2). DRAWINGS NAVAL ORDNANCE STATION, INDIAN HEAD, MD (CAGE Code 19200 and 19203) 10521632 Cartridge, Delay, Ml55 Assembly 8798143 8798142 DL10521631 9216933 Box, Fiberboard (Inner) Packing, Ammunition for Initiator, Cartridge Ac

9、tuated, Delay, MIO, M30A1, M31, M32A1, M42, M43A1, M72, M92, or M114 Box, Packing, Ammunition for Initiator, Cartridge Actuated, Delay, M10, M30A1, M31, M32A1, M42, M43A1, M72, M92, or M114 Initiator, Cartridge Actuated, Delay, M72, Assembly Box, Fiberboard (Outer) Alternative, Packing Ammunition, f

10、or Initiator, Cartridge Actuated, Delay, M10, M30A1, M31, M32A1, M42, M43A1, M72, M92, or M114 U.S. AIR FORCE TPO 00-062-5879 Initiator, Cartridge Actuated, M72 (Application fir copies should be addressed to: Commanding Officer, Naval Ordnance Station, Data Control Branch (Code 3720), Indian Head, M

11、D 20640-5000.) 2.2 Order of precedence, In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtaine

12、d. 3. REQUIREMENTS 3,l Materials, All materiais used in the manufacture of the initiators shall conform to the specifications referred to on the respective drawings unless specific approval in writing covering a departure has been obtained from the cognizant Navy design activity prior to manufacture

13、. When alternate materials or methods of manufacture are specified on the drawings, the bidders selections shall be clearly stated in the proposal. 3.2 Components. 32.1 Primary components. For the purpose of this specification, the Ml55 delay cartridge (Drawing 10521632) is defrned as a primary comp

14、onent. Only primary components from a single lot shall be used in a production lot of initiators. One primary component production lot may be used in more than one initiator production lot. 3.2.2 Component parts. All component parts shall meet the applicable requirements of MIL-1-14857 or MIL- 14029

15、6 prior to assembly. 3.3 Breakaway torque. The chamber and cap of each assembled initiator shall withstand a breakaway torque application of 400 inch-pounds without loosening or deformation (see 4.3.1). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

16、-,-MIL-I-60532A 33 7779906 0425533 O U Temperature pF) -60 to -70 65 to 75 195 to 205 3A Residual maGe-The initiator shall not deflect the inrlicator of the compass more than five degrees in either direction (see 4.3.2). - -_ Pressure (psi) Minimum Maximum Delay time (sec) 500 1250 aao f 0.100 600 1

17、500 0.495 f 0.100 700 1700 0.450 f 0.075 3.5 Radiographic examination. Each initiator assembly shall be radiographically examined br defects (see 4.3.3). _ - 3.6 Fnctional. 361.1 Initiation. The initiator shall be fired by a source delivering an output pressure of 700 +25, -0 pounds per square inch

18、(gage) (psig) at 70 f 5 OF. 362 Misfires. here shall be no misfires. 3.6.3 Mechanical failures. The initiator shall function without mechanical failure (see 6.6.2). 3.7 Workmanship. Initiators shall be free of cracks, splits, incomplete or damaged threads on inlet and outlet ends, or other defects w

19、hich might prevent proper mating with connecting parts or proper functioning of the device. 3.7.1 Metal defects. All components shall be free from cracks, splits, cold shuts, inclusions, porosity - or any similar defect. 3.7.2 Burr. No part shall have a burr which might interfere with the assembly o

20、r function of the item or which might be injurious to personnel handling the item. 3.7.3 Foreign matter. No part or assembly shall contain chips, dirt, grease, rust, corrosion or other foreign matter. 4, QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in th

21、e contract or purchase order, the contractor is responsible for the perfbrmance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the perfor

22、mance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any ofthe inspections set forth in the specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirement

23、s (see 6.2). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- flIL-I-60512A 33 W 777770b 0425534 2 MIL-I-60512A a 4.1.1 Respomibity for compliance, All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specific

24、ation shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance compl

25、y with all requirements of the contract. Sampling inspection, as part Df manufacturing operations, is an acceptable practice to ascertain conformance to requirements; however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Governmen

26、t to accept defective material. 4.1.2 Quaty assurance terms and definitions. Reference shall be made to MIL-STD-109 to define the quality assurance terms used. 4.1.3 Inspection. Inspection shall be in accordance with MIL-A-2550 and MIL-STD-453. 4.2 Inspection provisions. 4.2.1 Lot. 4.2.1.1 Submissio

27、n of product. Unless otherwise specified by the contracting activity, formation and identification of lots shall be in accordance with MIL-STD-105. 4.2.1.2 Size of lot. A lot shall consist of an identifiable group of assembled initiators containing metal parts assemblies produced by a homogeneous pr

28、ocess and loaded with one lot of accepted cartridges. 4.2.2 Examination. One-hundred percent examination shall be performed for all critical defects. Examination for major and minor defects shall be pehrmed in accordance with the classification of defects. Four power (4X) magnification may be used f

29、or inspection of such defects as burr and foreign matter. When compliance with the applicable requirement is in doubt as a result of visual examination, the characteristic shall be measured or gaged to determine acceptability. All nonconforming material shall be rejected. 4.2.2.1 Cartridge, Initiato

30、r, Delay, MlS5, Drawing 10521632, covering a detail of Drawing 10521631. Characteristic Defect Method of Inspection 1 Mixed cartridges Visual 2 Metal defective Visual 3 O-ring missing Visual 4 Sealing disc missing, damaged, or improperly secured Visual 101 O-ring split, cut, or cracked Visual 102 Fo

31、reign matter present Visual 201 Case scratched, wrinkled, bulged, or dented Visual 202 Varnish missing or inadequate Visual Critical Major Minor 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c - MIL-I-bO512A 13 9997906 0425515 4 MIL-I-60512A 4.2.

32、2.2 Assembly, Drawing 05263I9 lm Drawings 8595254, 8594857, 8594868, 10521632, and MILC-SO/lQ and MIGC-550a/11. Characteristic Defect Method of Inspection Critical Major 1 Set screw misisng 101 Thread damaged 102 Burr 103 Foreign matter present Minor None defined Visual Visual Visual Visual 4.2.2.3

33、Assembly, Drawing 10S1639 lm Drawings 859487, 8594864 105521632, MILC-550U10, and MILC-5501/11, Critical 1 Screw missing Visual Major 101 Thread damaged Visual Burr Wsual 102 103 Foreign matter present Visual Minor None defined 4.2.24 Assembly, Drawing 10521631, less Drawings 8594857, MIGC-550U10, a

34、nd MTGC-55OUll. Critical 1 Cartridge loose 2 Cartridge retainer loose 3 4 Major None defined Minor Metering groove of cartridge retainer missing Elongated hole of cartridge retainer missing None defined 4.2.2.5 Assembly, Drawing 10521631, less C-550ln110 and MTGC-5501/11. Critical 1 Location of cart

35、ridge retainer 2 3 Any part missing 4 Improper assembly 5 Shear pin no6 engaged in firing pin Foreign matter in gas port 5 ManualNisual Manual/Visual Visual Visual - X-ray GagelX-ray VisuaVX-ray VisudlX-ray Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

36、rom IHS-,-,-MIL-I-bO532A 13 M 7777906 0425536 6 W MIL-I-60512A Characteristic Defect Major 101 . Minor Length from firing pin housing boss face to gas port face, max 201 Varnish missing or inadequate 202 Location of label, incorrect 203 Barrier material missing from set screw 4.2.26 Assembly, Drawin

37、g 10521631. , Critical 1 Major 101 Height of cap, max 102 Minor 201 %tal length, max 202 Location of marking incorrect 203 Protective cap or plug missing 204 Marking missing, incorrect or illegible Cap set screw missing, loose or above flush . Protective finish inadequate or defective 4.2.2.7 Box, F

38、lberboard (Inner) Ammunition, Drawing 8798143. Critical None defined Major None defined Minor 201 Contents loose 202 Box damaged 203 204 205 Sealing strip broken or missing Marking missing, incorrect, or illegible Cut, damaged, or improperly sealed bag 4.2.28 Box, Ammunition Packing, Drawing 8798142

39、. Cri tic al None defined Major None defined Method of Inspection Gage Visual Visual Visual Visual Gage Visual Measure Visual Visual Visual Manual Visual Visual Visual Visual Minor 201 Contens loose 202 203 Contents of hox exposed Strapping missing, loose, broken, or improperly engaged Manual O Visu

40、aVManual Visual 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-60512A lmperature (OF) -6otO -70 65 to 75 195 to 205 Characteristic Defect Method of Inspection Sample size 7 7 7 204 Box damaged 205 206 Number of units incorrect Marking missin

41、g, incorrect, or illegible Visual Visual visual 4.2.29 Box, Rberboard (Outer) Alternative Ammunition Packing, Drawing 9216933. Critical None defined Major None defined Minor 201 Contents loose 202 Carton broken or damaged 203 204 205 lpe incomplete Number of units contained incorrect Marking missing

42、, incorrect, or illegible ManualNisual visual visual Visual Visual 4.2.3 Inspection testing. The following tests shall be perbrmed in accordance with 4.3. 4.2.3.1 Breakaway torque. Each assembly shall be subjected to the breakaway torque test of the threaded joint between the cap and the chamber. Fa

43、ilure of any assembly to comply with 3.3 shall be cause for rejection of the assembly. 4.2.3.2 Residual magnetism. Each initiator shall be subjected to the test for excessive residual magnetism as specified in 4.3.2. Failure of any initiator to comply with 3.4 shall be cause for rejection of the ini

44、tiator. 4.2.3.3 Eunctional tests. The following tests shall be performed by the Government. 4.2.3.3.1 Ballistics. Twenty-one units shall be tested to determine compliance with 3.6. The units shall ba temperature conditioned as provided in table Il and 4.3.3.2. Failure of any unit to comply with 3.6 shall be cause for rejection of the lot. 4.2.3.3.2 Retest, There shall be no retests. 4.2.3. IPW - 704-034/30589 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-