NAVY MIL-DTL-15119 B-2012 TUBING ROUND SEAMLESS ALLOY STEEL.pdf

《NAVY MIL-DTL-15119 B-2012 TUBING ROUND SEAMLESS ALLOY STEEL.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-15119 B-2012 TUBING ROUND SEAMLESS ALLOY STEEL.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 Comments, suggestions, or questions on this document should be addressed to: Commander, Naval Sea Systems Command, ATTN: SEA 05S, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard DC 20376-5160 or emailed to CommandStandardsnavy.mil, with the subject line “Document Comment”. Since contact

2、 information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.dla.mil. AMSC N/A FSC 4710 INCH-POUND MIL-DTL-15119B(OS) 11 September 2012 SUPERSEDING MIL-T-15119A(OS) 20 October 1976 DETAIL SPECIFICATION TUBING, ROUND, SEAML

3、ESS ALLOY STEEL This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers round seamless alloy steel tubing (see 6.1). 1.2 Class

4、ification. Tubing covered by this specification are of the following grades, as specified (see 3.2 and 6.2): Grade A No. 4130 Grade B No. 8630 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not i

5、nclude documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in section

6、s 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of

7、these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1916 - DoD Preferred Methods for Acceptance of Product DOD-STD-2101 - Classification of Characteristics (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or ht

8、tps:/assist.dla.mil.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15119B(OS) 2 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of

9、 these documents are those cited in the solicitation or contract. ASTM INTERNATIONAL ASTM E8/E8M - Standard Test Methods for Tension Testing of Metallic Materials ASTM E112 - Standard Test Methods for Determining Average Grain Size ASTM E350 - Standard Test Methods for Chemical Analysis of Carbon St

10、eel, Low Alloy Steel, Silicon Electrical Steel, Ingot Iron, and Wrought Iron ASTM E1282 - Standard Guide for Specifying the Chemical Compositions and Selecting Sampling Practices and Quantitative Analysis Methods for Metals, Ores, and Related Materials (Copies of these documents are available from A

11、STM International, 100 Barr Harbor Dr., P.O. Box C700, West Conshohocken, PA 19428-2959 or online at www.astm.org.) NCSL INTERNATIONAL ANSI/NCSL Z540.3 - Requirements for the Calibration of Measuring and Test Equipment (Copies of this document are available from NCSL International, 2995 Wilderness P

12、lace, Suite 107, Boulder, CO 80301-5404 or online at www.ncsli.org.) SAE INTERNATIONAL SAE-AMS2253 - Tolerances, Carbon and Alloy Steel Tubing SAE-AMS2806 - Identification Bars, Wire, Mechanical Tubing, and Extrusions, Carbon and Alloy Steels and Corrosion and Heat-Resistant Steels and Alloys SAE-AM

13、S2807 - Identification, Carbon and Low-Alloy Steels, Corrosion and Heat-Resistant Steels and Alloys, Sheet, Strip, Plate, and Aircraft Tubing SAE-AMS-H-6875 - Heat Treatment of Steel Raw Materials (Copies of these documents are available from SAE World Headquarters, 400 Commonwealth Drive, Warrendal

14、e, PA 15096-0001 or online at www.sae.org.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersed

15、es applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Manufacture (M101). The tubing shall be drawn from fully killed steel manufactured by either the open hearth or electric furnace process. M101 indicates this is a major requirement that shall be int

16、erpreted in accordance with 4.3. The classification of 4.3 shall apply for similarly designated critical (Cx) and major (M1xx) requirements throughout this specification. 3.2 Chemical composition (M102). The chemical composition of the steel shall be as specified in table I, determined in accordance

17、 with 4.4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15119B(OS) 3 TABLE I. Chemical composition. Element Grade 4130 8630 Analysis (%) Check Analysis Tolerance (%) Analysis (%) Check Analysis Tolerance (%) Carbon 0.27 0.33 0.02 0.27 0.33

18、 0.02 Manganese 0.40 0.60 0.03 0.70 0.90 0.03 Phosphorous 0.025 (max.) 0.005 0.025 (max.) 0.005 Sulfur 0.025 (max.) 0.005 0.025 (max.) 0.005 Silicon 0.20 0.35 0.02 0.20 0.35 0.02 Nickel 0.40 0.70 0.03 Chromium 0.80 1.10 +0.05, -0.03 0.40 0.60 0.03 Molybdenum 0.15 0.25 0.02 0.15 0.25 0.03 NOTE: 1. In

19、dividual determinations may vary from the specified range to the extent shown in the check analysis column except that elements in any heat shall not vary both above and below specified range. The average of all separate determinations shall be within the specified range. 3.3 Grain size (M103). The

20、grain size of the steel used for this tubing shall be predominately No. 5 or finer with grains as large as No. 3 permissible. The grain size shall be determined in accordance with 4.5. 3.4 Mechanical properties (M104). After the last cold draw pass, the tubing shall be heat treated in accordance wit

21、h SAE-AMS-H-6875 to produce the mechanical properties listed in table II. Mechanical properties shall be verified in accordance with 4.6. TABLE II. Mechanical properties. Tensile Strength (PSI) Yield Strength at 0.2% Offset (PSI) Elongation in 2 Inches Full Tube Specimen (%) 110,000 130,000 85,000 1

22、20,000 12 22 3.5 Dimensions (M105). The tubing dimensions shall be as specified (see 6.2). Dimensions shall be verified in accordance with 4.7. 3.6 Tolerances (M106). Unless otherwise specified (see 6.2), the permissible variations in dimensions shall be as specified in SAE-AMS2253. Tolerances shall

23、 be verified in accordance with 4.8. 3.7 Hydrostatic test (C1). The tubing shall not break or permanently increase in diameter more than 0.003 inches when tested in accordance with 4.9 (see 6.2). 3.8 Marking. All tubing shall be marked in accordance with SAE-AMS2806 and SAE-AMS2807. Marking shall be

24、 verified in accordance with 4.10. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15119B(OS) 4 3.9 Workmanship. The tubing shall have a smooth, clean surface, free from heavy scale or oxide, pipes, burrs, seams, cracks, tears, grooves, lamin

25、ations, slivers, pits, and other injurious defects that may affect its suitability for the purpose intended. Surface imperfections such as handling marks, straightening marks, light mandrel and die marks, shallow pits, and scale patterns shall not be considered as injurious defects, provided the imp

26、erfections are not deeper than may be removed without reducing the diameter or wall thickness of the tubing below the permissible tolerance limits. The removal of surface imperfection is not required. Workmanship shall be verified in accordance with 4.11. 4. VERIFICATION 4.1 Conformance inspection.

27、The examination and testing of tubing shall be classified as conformance inspection. Inspection sampling requirements for critical, major, and minor characteristics are defined in MIL-STD-1916. Unless otherwise specified (see 6.2), Inspection Level IV shall be used for all characteristics defined as

28、 major and Inspection Level II for all minor characteristics; critical characteristics shall be addressed in accordance with MIL-STD-1916. In addition to the sampling requirements stated herein, Verification Level VII shall be used to verify the 100 percent screening operation of critical characteri

29、stics. 4.2 Lot. A lot shall consist of homogenous tubing produced from the same heat and the same heat treatment. See 6.5 for definitions. 4.3 Classification of characteristics. The characteristics verified by the tests and examinations herein are classified as critical, major, or minor in accordanc

30、e with DOD-STD-2101. Tests and examinations that verify critical characteristics are identified by the symbol (C) and major characteristics by the symbol (M). The number following the classification symbol indicates the serial number of the test or examination. Tests and examinations which are not a

31、nnotated with a classification code are classified minor. 4.4 Chemical composition. 4.4.1 Sampling. At least five samples shall be selected for check chemical analysis to represent the heat in the lot. Failure of the samples to meet requirements of 3.2 shall be cause for rejection of the lot represe

32、nted. Check chemical analysis may be waived provided that all of the material in the lot can be identified as being made from a heat previously analyzed and found to conform to the chemical composition specified herein. 4.4.2 Method. Specimens shall be prepared in accordance with ASTM E1282 and shal

33、l be tested by wet chemical methods in accordance with ASTM E350. 4.5 Grain size. 4.5.1 Sampling. Grain size shall be determined on a billet before piercing, hot working, or cold drawing. One or more samples shall be selected from one or more billets used in making the tubing lot and suitable for de

34、termining the grain size. Failure of the sample to meet the requirements of 3.3 shall be cause for rejection of the lot represented. 4.5.2 Method. Specimens shall be taken one-half way between the center and outside of the billet. The specimens shall be approximately 1 inch square or round and norma

35、lized at 1650 F. The specimens shall be prepared and the grain size determined in accordance with ASTM E112. 4.6 Mechanical properties. 4.6.1 Sampling. At least one tensile test sample shall be selected from each 1000 feet or less of each lot for determination of mechanical properties. Failure of th

36、e sample to meet the requirements of 3.4 shall be cause for rejection of the lot represented. 4.6.2 Method. Specimens shall be prepared and tested in accordance with ASTM E8/E8M. 4.7 Dimensions. Dimensions shall be verified using standard measuring instruments whose calibration is managed by a calib

37、ration system compliant with ANSI/NCSL Z540.3 or a government-approved equivalent. 4.8 Tolerances. The tolerances shall be verified using standard measuring instruments whose calibration is managed by a calibration system compliant with ANSI/NCSL Z540.3 or a government-approved equivalent. Provided

38、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15119B(OS) 5 4.9 Hydrostatic test. All tubing shall be subjected to the minimum hydrostatic pressure specified (see 6.2). The test shall be performed on tubing lengths up to 12 feet. The outside diameter

39、 of each test length shall be gauged in the same location before and after application of the specified pressure. Failure of the tubing to meet the requirements of 3.7 shall be cause for rejection of the lot. 4.10 Marking. The marking requirements of 3.8 shall be verified by visual inspection. 4.11

40、Workmanship. All tubing shall be visually examined for compliance with surface conditions and workmanship requirements. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be perfo

41、rmed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within th

42、e military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanator

43、y nature that may be helpful, but is not mandatory.) 6.1 Intended use. The seamless alloy steel tubing covered by this specification is manufactured into primer tubes subjected by explosive charges to high internal gas pressures of short duration. Since the primer tubes are manufactured for use in U

44、. S. Navy gun ammunition, there is no commercial application. 6.2 Acquisition requirements. Acquisition documents should specify the following: a. Title, number, and date of this specification. b. Grade of material (see 1.2). c. Dimensions (see 3.5). d. Quantity and lengths. e. Tolerances, if other

45、than specified in 3.6. f. Hydrostatic test pressure (see 3.7, 4.9, and 6.3). g. Conformance inspection levels, if other than specified in 4.1. h. Packaging, if other than specified in 5.1 and 6.4.2. i. Preservation, if other than specified in 6.4.1. Provided by IHSNot for ResaleNo reproduction or ne

46、tworking permitted without license from IHS-,-,-MIL-DTL-15119B(OS) 6 6.3 Hydrostatic test fiber stress. The pressure criteria for the hydrostatic test is as specified (see 6.2.f). It is intended that the tubes covered by this specification be subjected by the hydrostatic pressure test to a fiber str

47、ess no greater than 75,000 pounds per square inch as calculated from the following formula: 2222 ab abPS Where: S=Fiber stress in pounds per square inch P=Hydrostatic test pressure in pounds per square inch b=Outside radius of the tube in inches a=Inside radius of the tube in inches6.3.1 Rejection d

48、ue to failing hydrostatic test. Failure of hydrostatic test should be cause for rejection of the tubing lot. The Government may waive rejection of this CRITICAL requirement if a subsequent investigation into the failure is able to determine that a) the root cause for the failure is isolated to the t

49、ubing that failed, and b) the tubing otherwise meets all of the requirements of the contract and this specification, and c) sufficient measures are in place to prevent defective tubing from this lot from being used in a gun primer. 6.4 Packaging. 6.4.1 Preservation. Unless otherwise specified (see 6.2), all tubing should be coated inside and outside with corrosion preventive compound conformi