NAVY MIL-DTL-14857 B-2005 INITIATOR CARTRIDGE ACTUATED DELAY M10 M31 M42 M72 AND M114 REMANUFACTURED METAL PARTS ASSEMBLY《 M10 M31 M42 M72 和M114型再造金属零件装配延迟弹筒驱动引发器》.pdf

《NAVY MIL-DTL-14857 B-2005 INITIATOR CARTRIDGE ACTUATED DELAY M10 M31 M42 M72 AND M114 REMANUFACTURED METAL PARTS ASSEMBLY《 M10 M31 M42 M72 和M114型再造金属零件装配延迟弹筒驱动引发器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-14857 B-2005 INITIATOR CARTRIDGE ACTUATED DELAY M10 M31 M42 M72 AND M114 REMANUFACTURED METAL PARTS ASSEMBLY《 M10 M31 M42 M72 和M114型再造金属零件装配延迟弹筒驱动引发器》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-DTL-14857B 3 March 2005 SUPERSEDING MIL-I-14857A 30 March 1990 DETAIL SPECIFICATION INITIATOR, CARTRIDGE ACTUATED, DELAY, M10, M31, M42, M72, AND M114 REMANUFACTURED METAL PARTS ASSEMBLY This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE

2、 1.1 Scope. This specification covers the requirements for the M10, M31, M42, M72, and M114 Delay Cartridge Actuated Initiator Remanufactured Metal Parts Assembly (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4 or 5 of this specific

3、ation. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements

4、 of documents cited in sections 3, 4 or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks . The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless other

5、wise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MILITARY MIL-A-2550 Ammunition, General Specification for AMSC N/A FSC 1377 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. INCH POUND

6、 Comments, suggestions, or questions on this document should be addressed to Commander, Indian Head Division, Naval Surface Warfare Center, Technical Information Branch (Code 4230), 101 Strauss Avenue, Indian Head, Maryland 20640-5035, or emailed to amanda.pennnavy.mil. Since contact information can

7、 change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil/ Source: http:/assist.daps.dla.mil - Downloaded: 2005-06-22T14:09ZCheck the source to verify that this is the current version before use.Provided by IHSNot for Resal

8、eNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14857B 2 DEPARTMENT OF DEFENSE STANDARDS MILITARY MIL-STD-413 Visual Inspection Guide for Elastomeric O-rings (Copies of these documents are available online at http:/assist.daps.dla.mil/ or from the Standardization Docume

9、nt Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, th

10、e issues of these documents are those cited in the solicitation or contract. DRAWINGS 8594862 Initiator, Cartridge Actuated, Delay, Metal Parts Assembly 8798143 Box, Fiberboard (Inner) Packing, Ammunition for Initiator, Cartridge Actuated, Delay, M10, M30A1, M31, M32A1, M42, M43A1, M72, M92, or M114

11、 8798142 Box, Packing, Ammunition for Initiator, Cartridge Actuated, Delay, M10, M30A1, M31, M32A1, M42, M43A1, M72, M92, or M114 9216933 Box, Fiberboard (Outer) Alternative, Packing Ammunition, for Initiator, Cartridge Actuated, Delay, M10, M30AI, M31, M32A1, M42, M43A1, M72, M92, or M114 (Applicat

12、ion for copies should be addressed to: Commander, Indian Head Division, Naval Surface Warfare Center, Attn: Technical Information Branch (Code 4230), Indian Head, MD 20640-5035.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unl

13、ess otherwise specified, the issues of these documents are those cited in the solicitation or contract. AMERICAN NATIONAL STANDARD INSTITUTE/AMERICAN SOCIETY FOR QUALITY ANSI/ASQ Zl.4 Sampling Procedures and Tables for Inspection by Attributes ANSI/ASQ A8402 Quality Management and Quality Assurance

14、- Vocabulary (Copies of these documents are available online at http:/webstore.ansi.org/ansidocstore/default.asp, or from the American Society for Quality, PO Box 3005, 611 E. Wisconsin Ave., Milwaukee, WI 53201-4606.) 2.4 Order of precedence. In the event of a conflict between the text of this docu

15、ment and the references cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unle ss a specific exemption has been obtained. Source: http:/assist.daps.dla.mil - Downloaded: 20

16、05-06-22T14:09ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14857B 3 3. REQUIREMENTS 3.1 Materials. All materials used in the manufacture of the initiators shall confor

17、m strictly to the specifications referred to on the respective drawings unless specific approval in writing covering a departure therefrom has been obtained from the cognizant Navy design activity prior to manufacture. When alternate materials or methods of manufacture are specified on the drawings,

18、 the bidders selections shall be clearly stated in the proposal. The remanufactured initiator metal parts assembly shall contain a new shear pin and O-rings. 3.2 Hydrostatic pressure. The initiator chamber and cap shall withstand a hydrostatic pressure of 5500 to 6500 pounds per square inch (psi) fo

19、r 15 seconds, minimum, without deformation or mechanical failure (see 6.3.1). 3.3 Protective finish. Protective finish shall be in accordance with the applicable specifications and drawings and shall apply to all surfaces of the component, regardless of configuration. Remanufactured exterior compone

20、nts shall have the existing protective finish stripped and the specified protective finish reapplied (see 6.3.2). 3.4 Residual magnetism. The metal parts assembly shall not deflect the indicator of the compass more than five degrees in either direction using procedures in 4.5.3. 3.5 Shear pin streng

21、th. The shear pin, after application of protective finish, shall shear when a load of 41 5 pounds is applied at the steady rate of 0.125 inch per minute. 3.6 Metal parts assembly. Parts shall be combined to produce an assembly which conforms to the requirements of the metal parts assembly drawing. A

22、ll threaded joints shall be assembled handtight. 3.6.1 Integrated plant products. When remanufacturing and loading of assembly is performed in an integrated plant, the metal parts assembly requirement may be waived and the residual magnetism requirement performed on the loaded assembly only. 3.6.2 T

23、hreaded component parts. Class 2A or 2B thread gage shall be used on component part inspection versus class 3A or 3B required on remanufactured hardware for initiators. 3.7 Workmanship. The requirements for workmanship are as specified on the applicable drawings, referenced specifications, and the f

24、ollowing: 3.7.1 Metal defects. All components shall be free from cracks, splits, cold shuts, inclusions, porosity, or any similar defect. 3.7.2 Burr. No part shall have a burr which might interfere with the assembly or function of the item or which might be injurious to personnel handling the item.

25、3.7.3 Foreign matter. No part or assembly shall contain chips, dirt, grease, rust, corrosion or other foreign matter. Source: http:/assist.daps.dla.mil - Downloaded: 2005-06-22T14:09ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction o

26、r networking permitted without license from IHS-,-,-MIL-DTL-14857B 4 4. VERIFICATION 4.1 Quality assurance terms and definitions. Reference shall be made to ANSI/ASC A8402 to define the quality assurance terms used. 4.2 Inspection conditions. Unless otherwise specified (see 6.2), all inspections sha

27、ll be performed under the following conditions: a. Temperature: Room ambient 68 to 77F b. Altitude: Sea level c. Humidity: 50 percent relative, maximum d. Atmospheric pressure: 14.7 psia 4.3 Quality conformance inspection. 4.3.1 Lot. 4.3.1.1 Submission of product. Unless otherwise specified by the c

28、ontracting activity, formation and identification of lots shall be in accordance with ANSI/ASQ Z1.4. 4.3.1.2 Size of lot. For the purpose of identification and shipment, the shipping lots of metal parts assemblies shall consist of 600 assemblies, maximum, provided the homogeneity requirements of ins

29、pection lots have been retained. 4.3.2 Examination. On reprocessed parts one-hundred percent examination shall be performed for all critical defects. Examination for major and minor defects shall be performed on a defect basis in accordance with the classification of defects. Four power (4) magnific

30、ation may be used in performing visual examination for such defects as burr and foreign matter. Inspection for rubber O-rings shall be in accordance with MIL-STD-413. When compliance with the applicable requirement is in doubt as a result of visual examination, the characteristics shall be measured

31、or gaged to determine acceptability. All nonconforming material shall be rejected. 4.3.2.1 Examination of reclaimed parts. Examination of reuseable parts, which require no reprocessing, shall be limited to inspection of defects that require visual type inspection. One hundred percent examination sha

32、ll be performed for all such defects. All nonconforming parts shall be reprocessed or rejected. 4.3.2.2 Retainer, Cartridge, Drawing 8594860, covering a detail of Drawing 8594862. Characteris tic Defect Method of Inspection Critical 1 Metering slots in base missing Visual Major 101 Pitch diameter of

33、 thread, max Gage 102 Minor diameter of thread, max Gage 103 Elongated slots, missing Visual Source: http:/assist.daps.dla.mil - Downloaded: 2005-06-22T14:09ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted wi

34、thout license from IHS-,-,-MIL-DTL-14857B 5 104 Thread damaged Visual 105 Metal defective Visual 106 Protective finish inadequate or defective Visual 107 Surface finish on internal radius and base, improper Visual 108 Burr Visual 109 Foreign matter present Visual Minor None defined 4.3.2.3 Chamber,

35、Initiator, Drawing 8594857 cove ring a detail of Drawing 8594862. Characteristic Defect Method of Inspection Critical None defined Major 101 Pitch diameter of large thread, min. Gage 102 Major diameter of large thread, min. Gage 103 Pitch diameter of small thread, min. Gage 104 Major diameter of sma

36、ll thread, min. Gage 105 Thread damaged Visual 106 Metal defective Visual 107 Protective finish inadequate or defective Visual 108 Surface finish, end of gas port, improper Visual 109 Burr Visual 110 Foreign matter present Visual Minor None defined 4.3.2.4 Cap, Drawing 8595254 covering a detail of D

37、rawing 8594862. Characteristic Defect Method of InspectionCritical 1 Metal defective in mounting flange surface Visual Major 101 Pitch diameter of thread, max. Gage 102 Minor diameter of thread, max. Gage 103 Thread damaged Visual 104 Metal defective Visual 105 Protective finish inadequate or defect

38、ive Visual 106 Burr Visual 107 Foreign matter present Visual Minor None defined Source: http:/assist.daps.dla.mil - Downloaded: 2005-06-22T14:09ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license

39、 from IHS-,-,-MIL-DTL-14857B 6 4.3.2.5 Pin, Shear, Drawing 8594745, covering a detail of Drawing 8594862. Characteristic Defect Method of Inspection Critical None defined Major 101 Diameter, max. Gage 102 Total length, min. Measure 103 Metal defective 104 Protective finish inadequate or defective Vi

40、sual 105 Surface finish improper Visual 106 Burr Visual 107 Foreign matter present Visual Minor 201 Total length, max. Gage 202 Profile of end Gage 4.3.2.6 Housing, Firing Pin, Drawing 8594858 covering a detail of Drawing 8594862. Characteristic Defect Method of Inspection Critical C1 Surface finish

41、 of cavity Gage Major 101 Pitch diameter of internal thread, max Gage 102 Minor diameter of internal thread, max Gage 103 Pitch diameter of external thread, min Gage 104 Major diameter of external thread, min Gage 105 Thread damaged Visual 106 Metal defective visual 107 Protective finish inadequate

42、or defective visual 108 Surface finish of cavity chamfer improper Visual 109 Burr Visual 110 Foreign matter present Visual Minor None defined 4.3.2.7 Pin, firing, Drawing 8594744 covering a detail of Drawing 8594862. Characteristic Defect Method of Inspection Critical None defined Major 101 Metal de

43、fective Visual Source: http:/assist.daps.dla.mil - Downloaded: 2005-06-22T14:09ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14857B 7 102 Protective finish inadequate o

44、r defective Visual 103 Surface finish of body and striker tip, improper Visual 104 Burr Visual 105 Foreign matter present Visual Minor None defined 4.3.2.8 Assembly, less Shear Pin, Cap, Cartridge Retainer and Chamber, Drawing 8594862, less Drawings 8594745, 8595254, 8594860, and 8594857. Characteri

45、stic Defect Method of Inspection Critical 1 Protrusion of firing pin Gage 2 O-ring missing Visual Major None defined Minor 201 O-ring not lubricated Visual 4.3.2.9 Assembly, less Cap, Chamber, Cartridge Retainer, Plug Machine Screw and Cap Machine Screw, Drawing 8594862 less Drawings 8595254, 859585

46、7, 8594860, NAS845-3 and NAS832-4. Characteristic Defect Method of Inspection Critical 1 Shear pin not engaged in firing pin Visual/Manual 2 Shear pin set screw missing Visual Major 101 O-ring missing or not lubricated Visual 102 Thread damaged Visual 103 Foreign matter present Visual Minor None def

47、ined 4.3.2.10 Assembly, Drawing 8594862. Characteristic Defect Method of Inspection Critical 1 Any part missing, except as otherwise classified Visual Major None defined Source: http:/assist.daps.dla.mil - Downloaded: 2005-06-22T14:09ZCheck the source to verify that this is the current version befor

48、e use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14857B 8 Minor 201 Protective cap or plug missing Visual 202 Protective finish inadequate or defective Visual 4.3.2.11 Box, Fiberboard (inner) Packing Ammunition, Drawing 8798143. Characte

49、ristic Defect Method of Inspection Critical None defined Major None defined Minor 201 Contents loose Manual 202 Box damaged Visual 203 Marking missing, incorrect, or illegible Visual 204 Cut, damaged or improperly sealed bag Visual 4.3.2.12 Box, Packing, Ammunition, Drawing 8798142. Characteristic Defect Method of Inspection Critical None defined Major None defined Minor