NAVY MIL-C-46237 (1)-1986 CARTRIDGE AIRCRAFT EJECTION SEAT CATAPULT M30A1《M30A1型航空器座椅弹射炮弹》.pdf

《NAVY MIL-C-46237 (1)-1986 CARTRIDGE AIRCRAFT EJECTION SEAT CATAPULT M30A1《M30A1型航空器座椅弹射炮弹》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-46237 (1)-1986 CARTRIDGE AIRCRAFT EJECTION SEAT CATAPULT M30A1《M30A1型航空器座椅弹射炮弹》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-46237(OS) AMENDMENT 1 14 October 1986 Beneficial comnents (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commanding Officer, Naval Ordnance Station, Standardization Branch (5241) , Indian Head, MD 20640-5000

2、. r. MI LI TARY SPEC I FI CAT I ON CARTRIDGE, AIRCRAFT EJECTION SEAT CATAPULT, M30A1 This amendment forms a part of Military Specification MIL-C-46237(MU), dated 24 June 1960, and is approved for use within the Naval Sea Systems Comand, Department of the Navy, and is available for use by all Departm

3、ents and Agencies of the Department of Defense. PAGE 1 2.1 Delete: “MIL-E-5272 . . .“ in its entirety. Delete: “MIL-STD-639 . .II in its entirety. Add: “MI L-STD-810 Environmental Test Methods and Engineering Guide1 ines“ PAGE 2 2.2 Change “2.2 Other publications.“ to “2.2 Other Government Pub1 icat

4、ions.“ Add: “2.3 Other publications. The following document forms a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the document which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise

5、 specified, the issues of documents not listed in the DODISS shall be the issue of the nongovernment documents which is current on the date of the sol ici tation. AMSC N/A Page 1 of 2 FSC 1377 DISTRIBUTION STATEMENT A: Approved for public release; distri bution is un1 imited. Provided by IHSNot for

6、ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-46237 (OS) Amendment 1 ANSI 846.1 Surface Texture (Surface Roughness, Waviness and Lay) (Application for copies should be addressed to the American National (Nongovernment standards and other pub1 ications are normally

7、available Standards Insti tute (ANSI), 1430 Broadway, NY 10018.) from the organization which prepares or which distributes the documents. These documents also may be available in or through libraries or other informational services . )II PAGE 3 3.5.1 delete I . . . in MIL-E-5272, Procedure XII . . .

8、II and substitute . . . in MIL-STD-810, Method 514.3, Test Procedure I, Test Condition 1-3.2.5 II II 3.7.2 delete “The Ordnance Standard Finish Blocks prescribed in MIL-STD-639“ and substi tute “The roughness comparison standards prescribed in ANSI 846.1“ PAGE 9 4.4.4 delete I . in MIL-E-5272, Procedure XII“ and substitute . MIL-STD-810, Method 514.3, Test Procedure I, Test Condition 1-3.2.5“ Preparing Acti vi ty: Navy - OS Project No. 1377-N834 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-