NAVY MIL-C-16385 E-1972 CARTRIDGE CARBON DIOXIDE INFLATABLE LIFE PRESERVER USE《膨胀型救生工具用二氧化碳弹药筒》.pdf

《NAVY MIL-C-16385 E-1972 CARTRIDGE CARBON DIOXIDE INFLATABLE LIFE PRESERVER USE《膨胀型救生工具用二氧化碳弹药筒》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-16385 E-1972 CARTRIDGE CARBON DIOXIDE INFLATABLE LIFE PRESERVER USE《膨胀型救生工具用二氧化碳弹药筒》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、MILITARY SPECIFICATION CARTRIDGE, CARBON DIOXIDE, INFLATABLE LIFE MI L-C- 16 3 8 SE (SHIPS ) SUPERSEDING 17 November 1972 28 July 1964 (See 6.5) MIL-C- 16 38 SD (SHIPS) PRESERVER USE 1. SCOPE # 1.1 This specification covers carbon dioxide cartridges for use with Underwater Demolition Team and Yoke T

2、ype SCUBA CO2 Inflatable Life Preservers (see 6.1). ( # 1.2 Classification. The cartridges furnished under the following types, as specified (see 6.1 and 6.2). this specification shall be of Type I - Cartridges containing 17 to 21 grams of CO2 Type II - cartridges containing 30 to 34 grams of CO2 2.

3、 APPLICABLE WCUMENTS 2.1 I The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of the specification to the extent specified herein. SPECIFICATIONS FEDERAL TT-1-558 - Ink, Matking Stencil, Opaque, For Nonporous Surfaces (Metals, PPP-B-566

4、 - Boxes, Folding, Paperboard. PPP-B-576 - Box, Wood, Cleated, Veneer, Paper Overlaid. PPP-B-585 - Boxes, Wood, Wirebound. PPP-B-591 - Boxes, Fiberboard, Wood-Cleated. PPP-8-601 - Boxes, Wood, Cleated-Plywood. PPP-B-621 - Boxes, Wood, Nailed and Lock-Corner. PPP-B-636 - Box, Fiberboard. PPP-B-676 -

5、Boxes, Set-up, Paperboard. PPP-T-97 - Tape, Pressure-Sensitive Adhesive, Filament Reinforced. MIL-M-19595 - Magnetic Effect Limits for Nonmagnetic Equipment Used Glass, Etc.). MILITARY In The Proximity of Magnetic Influence Ordnance. STANDARDS FEDERAL FED-STD-151 - Metals; Test Method. MTL-STD-105 -

6、 Sampling Procedures and Tables for Inspection by Attributes. MIL-STD-129 - Marking for Shipment and Storage. MILITARY (Copies of specifications, standards, drawings, and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activi

7、ty or as directed by the contracting officer.) I 2.2 Other ublicatiom The following document forms a part of this specification to the extontwiw Unleas otherwise indicated, the issue in effect on date of invitation for bids or request for proposal shall apply. UNIFORM CLASSIFICATION COMHTTIEE Unifor

8、m Freight Classification Rules. (Application for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Drive, Chicago, Illinois 60606.) FCC 4220 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-Lb3BSE

9、 42 W 9997906 046254i.1 9 W # # I I # # # # I # # MIL-C-16385E (SHIPS) (Technical society and technical association specifications and standards are generally available for reference from libraries. They are also distributed among technical groups and using Federal agencies.) 3. REQUIREMENTS 3.1 Sam

10、 le for first article ins ection. Pror to beginning production, samples shall be tercury and a tempercture of 77 f 18 degrees Fahrenheit (OF.). I 4.1 Test methods, I 4.7.1 Gas charge and leakage. The cartridges shall show no visible leakage when tested as follows: - (a) The weight of the empty cartr

11、idge shall be recorded. Filled cartridges shall r- be weighed to determine compliance with 3.10.1 and shall be immersed in water heated to 190 to 2OO0F. Cartridges shall remain in the water for 30 minutes minimum after temperature stabilization. All cartridges which show visible leakage shall be rem

12、oved. The gas charge shall be verified by weighing each cartridge after liquid dip cleaning. 4.7.2 irnensional ins ection (gage). Filled cartridges shall be dimensionally checked Failure of punctiir- with a “go” gage conform- cavity dimensions shown an figure 2. able area of cartridge to seat firmly

13、 against bottom of gage cavity shall be cause for rejection. 4.7.3 Hydrostatic res3ure test. Cartridges shali be subjected to an internal hydro- static ?ressure of 6506 at the option of the contractor, cartridges shall be separated by paperboard cell partitions. fied in the applicable box specificat

14、ion. 4 Box closure shall be as SpfICi- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-16 385E (CtlIPS) # 5.1.1.1 Intermediate containers. Eighteen unit packages as specified in 5.1.1 shall be intermediately packaged in fiberboard boxes conform

15、ing to PPP-B-636, class weather-resist- ant. Box closure shall be as specified in the appendix to PPP-B-636. # 5.1.2 Level c. Packaging shall be sufficient to afford adequate protection against deterioratio- physical amage during shipment from the supply source to the first receiving activity for im

16、mediate use or onboard storage for early installation. This level may conform to the suppliers commercial practice when such meets the requirements of this level. 5.2 Packing. # 5.2.1 Level A. Unless otherwise specified, cartridges, packaged as specified (see 6.2), shall be pacmn containers conformi

17、ng to any one of the following specificatims at the option of the Contractor: PPP-B-576 PPP-8-585 PPP-B-591 PPP-B-6 O1 PPP-B-6 21 PPP-B-6 36 Class 2 Class 3 Class 2 Overseas type Class 2 Weather-resistant Shipping containers shall be closed and strapped in accordance with the applicable box specific

18、ation or appendix thereto, except fiberboard boxes shall be banded with tape conform- ing to type III of PPP-T-97, and the appendix thereto. The gross weight of wood or wood cleated boxes shall not exceed 200 pounds: fiberboard boxes shall not exceed the weight limitations of the applicable box spec

19、ification. Intermediate fiberboard boxes, closed, sealed, and banded as specified herein, may be used as the shipping container. ers conformi- any one of the following specifications at the option of the contractor: # 5.2.2 Level 8. cartridges, packaged as specified (see 6.2) shall be packed in cont

20、ain- PPP-Ei-576 PPP-B-585 PPP-B-591 PPP-B-601 PPP-B-621 PPP-8-636 Class 1 Class 1 or 2 Class 1 Domestic type Class 1 Domestic Box closure shall be as specified in the applicable box specification or appendix thereto; The gross weight of wood or wood cleated boxes shall not exceed the weight limitati

21、ons of the applicable box specification. Intermediate fiberboard boxes, closed, sealed, and banded- as specified herein may be used as the shipping container. # 5.2.3 Level C. Cartridges, packaged as specified (see 6.2) shall be packed in con- tainers whichwill-insure acceptance by comon carrier and

22、 will afford protection against physical or mechanical damage during direct shipment from the supply source to the first receiving activity for immediate use or onboard storage for early installation. in general shall conform to the Uniform Freight Classification Rules or other carrier regulations a

23、s applicable to the mode of tranaportation and may be the suppliers commercial practice when such meets the requirements of this level. exterior cdrs shall be marked in accordance with MIL-STD-129 and as follows8 following information in such a manner that the markings shall not be damaged when cont

24、ainers are opened8 This level # 5.3 Markin . In addition to any special markings required (see 6.2), interior and # 5.3.1 Each interior or exterior container shall Le durably and legibly marked with the . Unless otherwise approved by mg activityTe6.1)-use o PO ystyrene oose-fill) naterial for domest

25、ic shipment and level C packqging and packing applications such as cushioning, filler, and dunnage is prohibited. When approved, unit packages and containers (interior and exterior) shall be marked as follows: CAUTION Contents cushioned, etc., with polystyrene (loose-Pill) material. Not to be taken

26、aboard ship. Remove and discard loose fill material before shipboard storage. If required, recushion with cellulosic material bound fiber, fiberboard, or transparent flexible cellular material. 6. NOTES # 6.1 Intended use. Cartridges furnished under this specification are intended for use in the fol

27、lowing LifeFrerervers: Type I - UDT life preservers conforming to MIL-L-16383. Type II - Yoke type SCUBA life preservers conforming to MIL-L-24047. I 6.2 Ordering data. Procurement documents should specify the following: (a) Title, number, and date of this specification. (b) Types (see 1.2). (c) Atm

28、ospheric condition, if different (see 4.6.1). (d) Selection of applicable levels of packaging and packing required (see 5.1 and (e) Special marking, other than as specified (see 5.3). if) Use of polystyrene material (see 5.4.2). 5.2). # 6.3 Applications for submitting material or equipment, or both,

29、 for magnetic effect tests should be made to: Officer-in-Charge, U.C. Naval Weapons Laboratory, Dahlgren, Virginia. The application should be made as far in advance of the anticipated submission date as is practicable, and should contain the following information: (a) Title and type (see 1.2). (b) S

30、ize and type of unit containers. (c) Quantity submitted. (d) Date of delivery. (e) Date completion is desired. (f) Reports required. (9) Disposition instructions, 6.3.1 Shipments of material or equipment submitted for magnetic effect test are to be addressed to: Receiving Officer U. S. Naval Weapons

31、 Laboratory Dahlgren, Virginia 6.3.1.1 The exterior containers of the shipments should be marked as follows: For inspection only Contract identification (Agency and contract or order number) # 6.4 First article Sns ection Invitations for bids should provide that the Govern- ment reser=- t6warvete re

32、quirement for samples for first article inspection as to those bidders offering a product which has been previously procured or tested by the Government, and that bidders offering such products, who wish to rely on such production or test, murt furnish evidence with the bid that prior Government app

33、roval is presently appropriate for the pending procurement. ./-. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-HIL-C-Lb385E 42 7779906 0462549 M !.IL-C- 16 38 SE (SHIPS ) 6.5 THE MARGINS OF THIS SPECIFICATION ARE MARKED “#“ TO INDICATE WHERE CHANGE

34、S (ADDI- TIONS, XODIFICATIONS, CORRECTIONS, DELETIONS) FROM THE PREVIOUS ISSUE HAVE BEEN XADE. THIS WAS DONE AS A CONVENIENCE ONLY AND THE GOVERNMENT ASSUMES NO LIABILITY WHATSOEVER FOR ANY INACCURACIES IN THESE NOTATIONS. BIDDERS AND CONTRACTORS ARE CAUTIONED TO EVALUATE THE TIONS AND RELATIONSIIIP

35、 TO THE LAST PREVIOUS ISSUE. REQUIREMENTS OF THIS DOCUMENT BASED ON THE ENTIRE COUTENT IRRESPECTIVE OF THE ANARGINAL NOTA- Preparing activity: Navy - SH (Project 4220-Nl65) 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-Lh385E 42 9999906 011

36、62550 4 SMOOTH FINISH FOR O-RING GASKET BLEND FROM .622 DIM. TO MAJR DIA. bF THD. DIM. - DIMENSINS IN INCHES. TOLERANCE- i ,OIS UIYLESS OTHERWISE SPECIFIED. 1.875 Dim. Thd. Min. 3 TOL . ;:kt id of s; Full W Figure 1 - Dimensions of cartridgt,. L 8 Provided by IHSNot for ResaleNo reproduction or netw

37、orking permitted without license from IHS-,-,-:.t I L-C - 16 3 3 5 E (Sil IPS 1 .062X4So CHAMFER ONE HOLE TAP* 10-24 FOR 3LG CUP POINT SET SCREW UCUT.06 i ROOT DIA. I i 1.500.001 ! I ALL DIMENSIONS ARE IN INCHES TOLERANCE .O156 UNLESS OTHERWISE SPECIFIED, Figure 2 - Cavity dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-