NAVY A-A-59798-2007 HELMET DAMAGE CONTROL FIRE FIGHTING《伤害调整型防火头盔》.pdf

《NAVY A-A-59798-2007 HELMET DAMAGE CONTROL FIRE FIGHTING《伤害调整型防火头盔》.pdf》由会员分享，可在线阅读，更多相关《NAVY A-A-59798-2007 HELMET DAMAGE CONTROL FIRE FIGHTING《伤害调整型防火头盔》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: Commander, Naval Sea Systems Command, ATTN: SEA 05Q, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard DC 20376-5160 or emailed to CommandStandard

2、snavy.mil, with the subject line “Document Comment”. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. FSC 4240 INCH-POUND A-A-59798 7 June 2007 COMMERCIAL ITEM DESCRIPTION HELMET, DAMA

3、GE CONTROL/FIRE FIGHTING The General Services Administration has authorized the use of this commercial item description, for all federal agencies. 1. SCOPE. This commercial item description covers the requirements for a one-size, high temperature resistant damage control/fire fighting (DC/FF) helmet

4、 for use aboard Navy ships by damage control personnel fighting below-deck fires. 2. SALIENT CHARACTERISTICS. 2.1 Design and construction. The DC/FF helmet is comprised of a shell, retention/suspension system, ear cover, face shield, and reflective markings. The shell consists of a one-piece molded,

5、 fiber reinforced composite that is designed to provide the user cranial, neck, eye, and ear protection from impact, heat, puncture, flame, and electrical hazards. The shell design incorporates a brim to divert water run-off to the rear of the shell. The shell design incorporates a removable/replace

6、able suspension system, which includes a ratchet cushioned headband system that is adjustable for head sizes 6 to 8. The helmet contains an aramid chin strap with a quick-release fastener and a removable, flame-resistant ear cover. 2.1.1 Sizes. The DC/FF helmet shall be made in one size only. Adjust

7、ment shall be made by the adjustable suspension system. 2.1.2 Weight. The weight of the complete helmet (face shield and retention system) shall not exceed 50 ounces. 2.1.3 Labeling. A commercial label is acceptable. If procured under contract, an additional permanent printed or stamped label contai

8、ning the contract number and the national stock number shall be included. 2.2 Materials. The contractor shall certify that the DC/FF helmet shall be constructed, tested, and labeled in accordance with the National Fire Protection Association (NFPA) Standard 1971, in addition to the following: 2.2.1

9、Shell. The design and measurement of the DC/FF helmet shall conform to figure 1. The shell must have an edge trim. The exterior surface of the shell shall be red in color. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59798 FIGURE 1. Helmet, da

10、mage control/fire fighting. 2.2.2 Retention system. Retention system shall include a suspension system, nape device, and chin strap. 2.2.2.1 Suspension system (energy absorbing system, headband, and crown strap). The design shall incorporate a removable/replaceable energy absorbing system containing

11、 an adjustable, ratchet type, cushioned head band/crown strap system. The crown straps shall possess a protective interface, so that the intersection of the straps does not rest directly on the user. This may be achieved with a cushioned headband liner or padding attached directly to crown strap int

12、ersection. All crown straps shall be positively attached to the suspension system. 2.2.2.2 Nape device. The nape device, located below the Bitragion Inion Arc, shall be used for helmet retention. 2.2.2.3 Chin strap. The chin strap shall consist of an aramid webbing containing a high temperature resi

13、stant, quick release fastener. The chin strap shall be attached to the outer shell. 2.2.3 Ear cover. The ear cover shall be constructed of a polybenzimidazole/Kevlar outershell material, moisture barrier, and liner, meeting a Thermal Protection Performance (TPP) rating of at least 20. TPP testing sh

14、all be conducted in accordance with NFPA 1971. The liner shall consist of meta or para-aramid and/or polybenzimidazole fiber or any combination thereof. The ear cover shall either be bound on all edges with the base fabric, or raw edges turned in and stitched. No raw or serged edges shall be visible

15、. The ear cover shall have a chin strap that is positively secured on one side and closed by means of hook and pile fastener tape to the other side. The chin strap shall be no less than 11.75 inches in length measured from intersection of edge of ear flap to end of chin strap. The center, back lengt

16、h of the ear cover measured from bottom edge of impact liner to bottom edge of ear cover shall be no less than 7 inches. 2.2.4 Face shield. The face shield shall be manufactured from a high heat material that has a heat deflection temperature of 325 F at 264 psi, 0.25-inch specimen, when tested in a

17、ccordance with ASTM D648. The face shield shall be either 4 or 5 inches in depth. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59798 2.3 Performance characteristics. 2.3.1 Penetration/impact resistance. The helmet shall be tested in accordan

18、ce with the physical penetration resistance test of NFPA 1971, after exposure to heat as outlined in NFPA 1971 for heat and thermal shrinkage resistance test, within 305 seconds after removal from heat source. The following exceptions shall apply: a. The drop height shall be 8 feet for the top plane

19、 and 4 feet for the side plane. b. During the top plane penetration test, the impact transmission force shall be measured. The electronic force measuring system shall be in accordance with the test method for top impact resistance of NFPA 1971. A single top impact force exceeding 850 pounds shall co

20、nstitute a failure. c. Two determinations shall be made for both top- and side-impact testing, one determination per helmet. d. The weight of the penetration test striker shall be 6 pounds, 10 ounces0.1 pound. The point of the striker shall have an included angle of 600.5 degrees and a cone altitude

21、 or height of not less than 1.5 inches. The radius of the striker point shall be 0.01970.004 inch. The hardness of the striking tip shall be a minimum of 60 Rockwell (Scale C). 3. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicab

22、le, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE PROVISIONS. 4.1 Product conformance. The products provided shall meet the salient characteristics of this Commercial Item Description, conform to the producers own drawings, specifications, st

23、andards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 5. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 6. NOTES. 6.1 Sou

24、rce of documents. 6.2.1 ANSI. ANSI standards are available from the American National Standards Institute, 25 W. 43rd St, 4th Floor, New York, NY 10036 or online at http:/webstore.ansi.org/. 6.2.2 ASTM. ASTM standards are available from ASTM International, 100 Barr Harbor Dr., PO Box C700, West Cons

25、hohocken, PA 19428-2959 or online at www.astm.org. 6.2.3 FAR. The Federal Acquisition Regulation may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402 or online at http:/www.arnet.gov/far. 6.2.4 NFPA. NFPA standards are available from NFPA, 1 Bat

26、terymarch Park, Quincy, MA 02169-7471 or online at www.nfpa.org. 6.3 Ordering data. The contract or order should specify the following: a. CID document number. b. National Stock Number. c. Product conformance provisions. d. Quantity required. 6.4 National stock numbers (NSNs). The NSN for this item

27、is 4210-01-493-7428. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59798 6.5 Key words. Damage control Fire fighter Firemans helmet Head protection Personnel protection Shipboard MILITARY INTERESTS CIVIL AGENCY COORDINATING ACTIVITY: GSA FSS

28、Custodians: Army EA Preparing Activity: Navy SH Navy SH Air Force 99 (Project 4240-2007-001) Review Activities: Air Force 03, 11, 84 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-