JEDEC J-STD-048-2014 Notification Standard for Product Discontinuance.pdf

《JEDEC J-STD-048-2014 Notification Standard for Product Discontinuance.pdf》由会员分享，可在线阅读，更多相关《JEDEC J-STD-048-2014 Notification Standard for Product Discontinuance.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、JOINT JEDEC/ECIA/IPC STANDARD Notification Standard for Product Discontinuance J-STD-048 (Revision of JESD48C, December 2011) NOVEMBER 2014 Electronic Components AssociationStandardsNOTICE JEDEC standards and publications contain material that has been prepared, reviewed, and approved through the JE

2、DEC Board of Directors level and subsequently reviewed and approved by the JEDEC legal counsel. JEDEC standards and publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of pr

3、oducts, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for use by those other than JEDEC members, whether the standard is to be used either domestically or internationally. JEDEC standards and publications are adopted without regard to whether or not the

4、ir adoption may involve patents or articles, materials, or processes. By such action JEDEC does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the JEDEC standards or publications. The information included in JEDEC standards and publicatio

5、ns represents a sound approach to product specification and application, principally from the solid state device manufacturer viewpoint. Within the JEDEC organization there are procedures whereby a JEDEC standard or publication may be further processed and ultimately become an ANSI standard. No clai

6、ms to be in conformance with this standard may be made unless all requirements stated in the standard are met. Inquiries, comments, and suggestions relative to the content of this JEDEC standard or publication should be addressed to JEDEC at the address below, or refer to www.jedec.org under Standar

7、ds and Documents for alternative contact information. Published by JEDEC Solid State Technology Association 2014 3103 North 10th Street, Suite 240 South Arlington, VA 22201-2107 ECIA Electronic Components Association 1111 Alderman Drive Suite 400 Alpharetta, GA 30005 IPC Association Connecting Elect

8、ronics Industries 3000 Lakeside Dr., Ste. 309S Bannockburn, IL 60015 USA +1 847-615-7100 tel +1 847-615-7105 fax This document may be downloaded free of charge; however JEDEC retains the copyright on this material. By downloading this file the individual agrees not to charge for or resell the result

9、ing material. Printed in the U.S.A. All rights reserved PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by JEDEC/ECIA/IPC and may not be reproduced without permission. For information, contact: JEDEC Solid State Technology Association 3103 North 10th Street Suite 240 South Arlington, VA 2

10、2201-2107 or refer to www.jedec.org under Standards-Documents/Copyright Information. JEDEC/ECIA/IPC Joint Standard No. 48 Page 1 NOTIFICATION STANDARD FOR PRODUCT DISCONTINUANCE (From JEDEC Board Ballot JCB-14-18, formulated under the cognizance of JC-14.4 Committee on Quality Processes and Methods.

11、) 1 Scope This standard is applicable to suppliers of, and affected customers for, electronic products and their constituent components. The goal of this notification standard is to better enable customers to manage and mitigate the disruption caused by the discontinuation of a product and ensure co

12、ntinuity of supply. This standard establishes the requirements for timely customer notification of planned product discontinuance, which will assist customers in managing end-of-life supply, or to transition ongoing requirements to alternate products. A Product Discontinuance business policy that ha

13、s been agreed to by the supplier and customer supersedes the requirements in this document. 2 Terms and definitions customer: Any organization that 1) has purchased a product from the supplier within the past two (2) years and has a contract or purchase agreement with product discontinuance notifica

14、tion requirements, or 2) has requested (and the supplier has agreed to provide) product discontinuance information, or 3) is an approved supplier agent. approved supplier agent: A direct sales channel, an authorized manufacturers representative, or an authorized distributor. authorized distributor:

15、A distributor that has an ongoing, contractual relationship with the supplier and a written agreement to sell the suppliers product. electronic product: An item containing one or more electronic devices performing major functions. product discontinuance: Discontinuation of product that will not be a

16、vailable for any reason. supplier: Any organization that 1) is the original product manufacturer and is thus responsible for generating the Discontinuance Notice, or 2) is an approved supplier agent. NOTE Any organization that is using a product that is scheduled to be discontinued as a component wi

17、thin their own product is not considered to be a supplier for purposes of this document and is not required to forward the Discontinuance Notice on to its customers; however, depending on how its product is affected, said organization must determine whether it needs to generate its own Discontinuanc

18、e Notice or Product-Process Change Notice for its own customers. JEDEC/ECIA/IPC Joint Standard No. 48 Page 2 3 Notification Requirements 3.1 Timing The supplier shall provide notice of product discontinuance to their customer(s) and approved supplier agents, allowing a minimum of 6 months from the n

19、otice to place final orders (last order date) and 12 months from the notice for final shipments (last ship date). The approved supplier agents shall, where applicable, notify their affected customers of the product discontinuance. 3.2 Format The product discontinuance notice shall be sent, in writin

20、g or electronically, to the customer or customers designated agent. The agent and/or contact will be identified by the customer. 3.3 Contents The product discontinuance notice shall include, at a minimum: a) Affected part number(s) b) Last order date c) Last ship date d) Supplier contact information

21、 (e.g., email, phone number) e) Reason for discontinuance f) Revision level of notice (if applicable) g) Suggested replacement product (if applicable) Customer part numbers are optional, if not required per agreed to customer criteria. 3.4 Alternative source / replacement product The supplier shall

22、assist customers by providing information, recommendations, and technical data to help locate an alternate source or select a replacement product. Under certain conditions this may not be applicable (e.g., custom or semi-custom products for which follow up products are not planned or viable). 3.4.1

23、Other options Upon customer request and supplier agreement, the supplier will negotiate with the customer other feasible options, such as the sale or transfer of technology and tooling, and the establishment of wafer or die banks to support on-going requirements. JEDEC/ECIA/IPC Joint Standard No. 48

24、 Page 3 Annex A (informative) The following governmental and commercial organizations collect and archive electronic part and product information which includes Product Discontinuance notices. This list is not all inclusive and there is no guarantee of the accuracy of the content of these websites,

25、but is only provided as information to the users of this standard. The Government Industry Data Exchange Program (GIDEP): www.gidep.org SiliconExpert: AVCOM: www.avcom- QTEC Solutions: www.qtec.us IHS: Total Parts Plus: SMART (RAC): www.mysmart- JEDEC/ECIA/IPC Joint Standard No. 48 Page 4 Annex B

26、 (informative) Differences between J-STD-048 and JESD48C This table briefly describes most of the changes made to entries that appear in this standard, J-STD-048, compared to its predecessor, JESD48C (December 2011). If the change to a concept involves any words added or deleted (excluding deletion

27、of accidentally repeated words), it is included. Some punctuation changes are not included. Clause Description of change Scope Change scope of affected products from solid state products to electronic products and their constituent parts. Scope Put more emphasis that intent of document is to mitigat

28、e customer disruption. Scope Add comment that existing agreements take precedent over this standard. 2 Update definition of “customer” to match format currently in JESD46. 2 Added “authorized manufacturers representative” to the definition of the term, authorized supplier agent. 2 Added definitions

29、for the terms “authorized distributor”, “electronic product”, and “supplier”. 3 Added “Notification” to the title of this clause. 3.1 In text of paragraph added the terms “last order date” and “last ship date” since they are the common terms used in the industry for these actions already described i

30、n this clause and are also used in clause 3.3. 3.3 Changed the presentation of the requirements from a sentence to a list, of one item per line of text. 3.3 Added items C to G as minimum content requirements in a notice. 3.4 Added “replacement product” to the title of the clause and within the text.

31、 3.4 Added clarifying statement that not all discontinued products may have replacements. 3.4.1 Modified text to clarify the intent of customer request to “customer request and supplier agreement”. Annex A Informative annex was updated. Standard Improvement Form JOINT JEDEC/ECIA/IPC J-STD-048 The pu

32、rpose of this form is to provide the Technical Committees of JEDEC with input from the industry regarding usage of the subject standard. Individuals or companies are invited to submit comments to JEDEC. All comments will be collected and dispersed to the appropriate committee(s). If you can provide

33、input, please complete this form and return to: JEDEC Attn: Publications Department 3103 North 10thStreet Suite 240 South Arlington, VA 22201-2107 Fax: 703.907.7583 1. I recommend changes to the following: Requirement, clause number Test method number Clause number The referenced clause number has proven to be: Unclear Too Rigid In Error Other 2. Recommendations for correction: 3. Other suggestions for document improvement: Submitted by Name: Phone: Company: E-mail: Address: City/State/Zip: Date: Electronic Components AssociationStandards