GMW GMW15487-2013 Determining the Resistance to Abrasion of Organic Coating Issue 2 English.pdf
《GMW GMW15487-2013 Determining the Resistance to Abrasion of Organic Coating Issue 2 English.pdf》由会员分享,可在线阅读,更多相关《GMW GMW15487-2013 Determining the Resistance to Abrasion of Organic Coating Issue 2 English.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、 WORLDWIDE ENGINEERING STANDARDS Test Procedure GMW15487 Determining the Resistance to Abrasion of Organic Coating Copyright 2013 General Motors Company All Rights Reserved June 2013 Page 1 of 5 1 Scope Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of
2、conflict between the English and domestic language, the English language shall take precedence. 1.1 Purpose. This standard shall be used to determine the resistance to abrasion of paints, varnishes and other organic coatings which have been applied to metallic or rigid non-metallic substrates. 1.2 F
3、oreword. Not applicable. 1.3 Applicability. Organic coatings which have been applied to metallic or rigid non-metallic substrates. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. DIN EN 196-1 DIN EN ISO 11124-2 I
4、SO 3310-1 2.2 GM Standards/Specifications. GMW3221 2.3 Additional References. None 3 Resources 3.1 Facilities. 3.1.1 Calibration. The test facilities and equipment shall be in good working order and shall have a valid calibration label. 3.1.2 Alternatives. Alternative test facilities and equipment m
5、ay also be used. However, all measuring variables as specified in this standard shall be determined correctly with respect to their physical definition. 3.2 Equipment. 3.2.1 Suitable saw or shears for preparation of test pieces. 3.2.2 Suitable test rig for measuring coating thickness. 3.2.3 Test sie
6、ve to ISO 3310-1, 0.8 mm for test sand. 3.2.4 Abrasion test rig (see Figure A1). 3.2.5 Test Sand. Sand shall be conform to DIN EN 196-1, grain group (0.5 to 1.0) mm. The sand shall be sieved by a sieve as specified in 3.2.3. The retained material shall be selected for the testing sand that shall be
7、used in this standard. 3.2.6 Chilled Iron Grit. Chilled iron grit shall conform to DIN EN ISO 11124-2, grain class (4.0 to 5.0) mm. The following iron grit shall be used: Chilled iron grit DIAMANT angular, code GH-K, grain class (4.0 to 5.0) mm, from Eisenwerk Wrth GmbH smaller components shall be p
8、laced together and adhered to the test piece holder to make up the minimum side length. The test pieces shall be taken from the finished part. If it is impracticable, tests shall be conducted on Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleN
9、o reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15487 Copyright 2013 General Motors Company All Rights Reserved June 2013 Page 2 of 5 specially prepared test panels. These panels shall be prepared with the same coatings and correct layer thic
10、knesses as the finished part. For initial sample approval, arbitration purposes, and routine quality control, at least three (3) test pieces shall be tested. 3.4 Test Time. Not applicable. 3.5 Test Required Information. Not applicable. 3.6 Personnel/Skills. Not applicable. 4 Procedure Abrasion resis
11、tance as determined by this test method shall be defined as a measure of the effect of sand/chilled iron grit falling from a defined height onto the inclined surface of the coating. A defined volume of sand/chilled iron grit falls through a tube onto the surface. This process shall be repeated until
12、 an area of 35 mm2 of the coating has been removed. The quantity of the needed sand/chilled iron grit must be measured. This value (in Liters (L) divided by the thickness (in microns (m) is the abrasion resistance of a coating. 4.1 Preparation. Test pieces shall be tested immediately after condition
13、ing to GMW3221 for periods as follows: For Oven-dried Organic Coatings: (24 to 30) h after coating and baking. For Air-dried Organic Coatings: (72 to 96) h after coating and drying. Parts From the Supplier: To be tested without conditioning, in the condition received. 4.2 Conditions. 4.2.1 Environme
14、ntal Conditions. Not applicable. 4.2.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 4.3 Instructions. 4.3.1 The test shall be performed at a temperature of
15、(+23 5) C. Care shall be taken to ensure that the test piece has attained this temperature. 4.3.2 The coating thickness shall be determined to within 2 m. 4.3.3. The quantity of specific test sand used for the test shall be dictated by the thickness of the coating being tested as follows: 15 m coati
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GMWGMW154872013DETERMININGTHERESISTANCETOABRASIONOFORGANICCOATINGISSUE2ENGLISHPDF

链接地址:http://www.mydoc123.com/p-757659.html