FORD WSS-M2F212-A4-2017 FABRIC PREMIUM VINYL (PVC) COATED WITH ENHANCED HAPTIC TOP COAT FOR PERFORATION TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSS-M2F212-A1).pdf

《FORD WSS-M2F212-A4-2017 FABRIC PREMIUM VINYL (PVC) COATED WITH ENHANCED HAPTIC TOP COAT FOR PERFORATION TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSS-M2F212-A1).pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M2F212-A4-2017 FABRIC PREMIUM VINYL (PVC) COATED WITH ENHANCED HAPTIC TOP COAT FOR PERFORATION TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSS-M2F212-A1).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 1 2017 09 01 Released-A4 Z. Jatkowski, NA 2015 03 02 Released D. Murtonen, NA Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 3 FABRIC, PREMIUM VINYL (PVC) COATED, WITH ENHANCED WSS-M2F212-A1 HAPTI

2、C TOP COAT FABRIC, PREMIUM VINYL (PVC) COATED, WITH ENHANCED WSS-M2F212-A4 HAPTIC TOP COAT FOR PERFORATION 1. SCOPE The material defined by this specification is an expanded polyvinyl chloride film laminated to a knitted polyester or polyester/cotton fabric. These materials can be used laminated wit

3、h foam and/or a backing fabric/scrim, based on the application. 2. APPLICATION WSS-M2F212-A1 was released originally for material used in interior trim as a covering for seating applications. WSS-M2F212-A4 was released originally for material used in interior trim as a perforated covering for seat a

4、pplications. Any other applications must be evaluated by the appropriate product engineer with functional testing and approved by Materials Engineering. 2.1 LIMITATIONS Product grain will be used to determine and classify the usage of this premium enhanced haptic topcoat polyvinyl chloride for Ford

5、and Lincoln vehicles. Areas where anti-squeak properties are required, WSS-M2F212-A vinyl cannot be used. Not to be used for truck or commercial vehicle, in any A surface. 3. REQUIREMENTS In addition to the requirements listed herein, this material shall meet all requirements of the WSS M8P3-E1/E3 o

6、r latest Performance, Flexible Polymeric Film, Interior Quality specification. Laminated materials must meet the lamination requirement per WSS-M8P3-E3 or latest performance specification. 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on th

7、e Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 CONDITIONING AND TEST CONDITIONS ENGINEERING MATERIAL S

8、PECIFICATION WSS-M2F212-A1/A4 Copyright 2017, Ford Global Technologies, LLC Page 2 of 3 All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the con

9、ditioning environment or soon after removal. 3.3 COMPOSITION 3.3.1 Vinyl Coated Fabric Composite 3.3.1.1 Weight (ASTM D 751, Sample Method) Total (vinyl and supported fabric) A1 820 945 g/m2 A4 Report 3.3.1.2 Thickness 1.0min. - 1.7max/mm 3.3.2 Supported Fabric (ASTM D 276) 3.3.2.1 Fabric Compositio

10、n Warp Knit made of 100% Polyester or 65% Polyester/35% Cotton Blend 3.3.2.2 Weight 125-135 g/m2 (ASTM D 751, Sample Method) 3.4 PHYSICAL PROPERTIES 3.4.1 Breaking Strength (ASTM D751, Grab Method) A1 WMD 480 N min AMD 455 N min A4 WMD Report AMD Report 3.4.2 Tear Strength (ASTM D751, Trapezoid Tear

11、) A1 WMD 145 N min AMD 145 N min A4 WMD Report AMD Report 3.4.3 Seam Strength (FLTM BN 119-01) A1 WMD 500 N min ENGINEERING MATERIAL SPECIFICATION WSS-M2F212-A1/A4 Copyright 2017, Ford Global Technologies, LLC Page 3 of 3 AMD 480 N min A4 WMD Report AMD Report 4. GENERAL INFORMATION The information

12、given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest fro

13、m Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Speci

14、fication. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.2 SUPPLIERS O

15、NGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements,

16、the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineering Material

17、Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.3 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company dir

18、ection applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis through IMDS and or GMAP reporting. 4.1 WSS-M2F212-A4 These materials may require the usage of dark colored foam and knit substrate to be used with dark color to prevent read through from the foam and knit substrate. 5. SUMMARY OF REVISIONS 09 01 2017 -Released A4 version