FORD SK-M14J9571-A-1994 THINNER《稀释剂》.pdf

《FORD SK-M14J9571-A-1994 THINNER《稀释剂》.pdf》由会员分享，可在线阅读，更多相关《FORD SK-M14J9571-A-1994 THINNER《稀释剂》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Release No. Released1994 12 19 Revised and Retyped was: 3 pages1980 03 06 SM/EQ8615 TP ReleasedWP 3948-a Page 1 of 2 THINNER SK-M14J9571-A1. SCOPEThe material defined by this specification is a thinner.2. APPLICATIONIn gener a

2、l the material is used to dilute the metallic two coat repairenamel SK-M1J9553-A.3. REQUIREMENTS3.1 COMPOSITIONBlen d of xylene, “Shellsol A/AB“, butylacetate, glycolacid-butylester, and butanol.3.2 DENSITY 0.870 - 0.871 g/cm3(ASTM D 1298-55)3.3 DISTILLATION RANGE 127 - 182 C(ASTM D 1078-67)3.4 FLAS

3、H POINT, min 23 C(ASTM D 56)3.5 REFRACTIVE INDEX 1.4648 - 1.4650(ASTM D 1218)3.6 COLOR Water white3.7 TOXICITYThe material shall conform to the safety regulations applicable tothe plant and/or countr y where the material shall be used and has tobe labeled accordingly if necessary. Further the materi

4、al shall nothave an obnoxious or objectionable odor.3.8 SHELF STABILITYMinimum 2 years as supplied in the original container.ENGINEERING MATERIAL SPECIFICATIONSK-M14J9571-AWP 3948-b Page 2 of 2 3.9 SUPPLIERS RESPONSIBILITYAll materials supplied to this specification must be equivalent inal l charact

5、eristics to the material upon which approval wasoriginally granted.Pri or to making any change in the properties, composition,constr uction, color, processing or labeling of the materialorig inally approved under this specification, whether or not suchchange s affect the materials ability to meet th

6、e specificationrequir ements, the Supplier shall notify Purchasing, Toxicology andthe affected Materials Engineering activity of the proposed changesand obtain the written approval of the Materials Engineeringactivity. Test data, t est samples and a new code identification areto be submitted with th

7、e request.Substance restrictions imposed by law, regulations or Ford, apply tothe materials addressed by this document. The restrictions aredefined in Engineering Materials Specification WSS-M99P9999-A1.4. APPROVAL OF MATERIALSMat erials defined by this specification must have prior approval by ther

8、esp onsible Materials Engineering activity. Suppliers desiring approvalof thei r materials shall first obtain an expression of interest from theaffec ted Purchasing, Design and Materials Engineering activity. Uponrequest, the Supplier shall submit to the affected Materials Engineeringactivity a comp

9、leted copy of their laboratory test reports, signed by aqualified and authorized representative of the test faci lity, demonstratingful l compliance with all the requirements of this specification (testresults, not nominal values), the material designation a nd code number, andtes t specimens for Ford evaluation. Fords engineering approval of amateri al will be based on its performance to this specification and on anassessment of suitability for intended processes and/or applications. Uponapprov al, the material will be added to the Engineering Material ApprovedSource List.