FORD SK-M14J9561-D-1995 THINNER RECYCLING BASECOAT SOLID COLOUR AND CLEARCOAT DILUTION OF PAINT (Shown on SK-M14J9561-A)《再生底漆、素色和清漆以及油漆稀释用稀释剂 列于标准SK-M14J9561-A上》.pdf

《FORD SK-M14J9561-D-1995 THINNER RECYCLING BASECOAT SOLID COLOUR AND CLEARCOAT DILUTION OF PAINT (Shown on SK-M14J9561-A)《再生底漆、素色和清漆以及油漆稀释用稀释剂 列于标准SK-M14J9561-A上》.pdf》由会员分享，可在线阅读，更多相关《FORD SK-M14J9561-D-1995 THINNER RECYCLING BASECOAT SOLID COLOUR AND CLEARCOAT DILUTION OF PAINT (Shown on SK-M14J9561-A)《再生底漆、素色和清漆以及油漆稀释用稀释剂 列于标准SK-M14J9561-A上》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Release No. Released1995 01 13 Revised and Retyped1993 06 01 EP00E10258817000 Version D added KW1985 01 17 B/001674TP Last ReleaseWP 3948-a Page 1 of 4THINNER SK-M14J9561-ATHINNER SK-M14J9561-BTHINNER SK-M14J9561-CTHINNER, REC

2、YCLING SK-M14J9561-D1. SCOPEThe materials defined by these specifications are thinners.2. APPLICATIONThese specifications were originally released for materials used forcle aning operations for metallic basecoats S-M32J110-B, solid colortopcoats SK-M98J9552-A and clearcoats SK-M32J9553-A.3. REQUIREM

3、ENTS3.1 STATISTICAL PROCESSSupplie rs must conform to the requirements of Ford Quality SystemStand ard Q-101. A mutually acceptable Control Plan as describedtherein is required for material/source approval. Appropriatestatist ical tools must be used to analyze process/product data sothat variation i

4、n the final product is continuously reduced.3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSISFord Motor Company, at its option, may conduct infrared and/ortherma l analysis of material/parts supplied to this specification.The IR spectra and thermograms established for i nitial approval shallcon

5、st itute the reference standard and shall be kept on file at thedesignated material laboratory. All samples sha ll produce IR spectraand thermograms that correspond to the reference standard when testedunder the same conditions.3.3 COMPOSITIONSK-M14J9561-A: Blend of aromatic hydrocarbons, g lycoleth

6、ers, alcoholsand a volatile antistatic compound.SK-M14J9561-B: Blend of organic solvents and volatile antistaticcompound and rust inhibitor.ENGINEERING MATERIAL SPECIFICATIONSK-M14J9561-A/B/C/DWP 3948-b Page 2 of 4 SK-M14J9561-C: Blend of organic solvents.SK-M14J9 561-D: Blend of 40 - 90 % SK-M14J95

7、61-C and 60 - 10 %distillate.3.4 PROPERTIES3.4.1 Density at 20 C(ASTM D 1298)SK-M14J9561-A 0 .869 - 0.874 g/mLSK-M14J9561-B 0 .869 - 0.876 g/mLSK-M14J9561-C 0 .872 - 0.878 g/mLSK-M14J9561-D 0 .854 - 0.870 g/mL3.4.2 Refractive Index at 20 C(ASTM D 1218)SK-M14J9561-A 1.483 - 1.488SK-M14J9561-B 1.465 -

8、 1.488SK-M14J9561-C 1.446 - 1.451SK-M14J9561-D Not applicable3.4.3 Color Colorless of light yellow3.4.4 Water Soluble Compounds, max 20 vol. %3.4.5 Dissolving Capacity for BakingEnamels in ProductionDi ssolving capacity for basecoat S-M32J110-B comparable toSK-M14J9556-A, for polyester enamel SK-M98

9、J9552- A and acrylicclearcoat SK-M32J9553-A comparable to S-M14J245-A.Test MethodPrep aration of Test Panels: Dilute enamel with releasedthinne r to a viscosity of 30 seconds FC 4 (20 C). Dipphosphated test panels (UMA 18005) into the dilu ted enamel ina vertical position and dry for 24 hours at roo

10、m temperature20 +/- 3 C, also in a vertical position.Tes t: Fill thinners SK-M14J9556-A, S-M14J245-A and thethinner under test into beakers. Dip one prepar ed test panelinto each beaker so that half of it is dipped into thethinner. Leave it there without stirring until the enamel iscompletely dissol

11、ved.Evaluation: The time to dissolve the enamel in the thinnerunder test shall be same as or less than the time todissolving in the comparable thinner.ENGINEERING MATERIAL SPECIFICATIONSK-M14J9561-A/B/C/DWP 3948-b Page 3 of 4 3.4.6 Specific Resistance S ee initial sampleTo be agreed with Manufacturi

12、ng Engineering Quality Controland supplier, minimum 350 k Ohm cm.3.5 QUALITYThe thinner must be ada ptable for application in accordance with theappropriate Ford Motor Company Process Specification. It shall notcontain any ingredients causing craters or deteriorate wettability.3.6 SUPPLIERS RESPONSI

13、BILITYAll materials supplied to this specification must be equivalent inal l characteristics to the material upon which approval wasoriginally granted.Pri or to making any change in the properties, composition,constr uction, color, processing or labeling of the materialorig inally approved under thi

14、s specification, whether or not suchchange s affect the materials ability to meet the specificationrequir ements, the Supplier shall notify Purchasing, Toxicology andthe affected Materials Engineering activity of the proposed changesand obtain the written approval of the Materials Engineeringactivit

15、y. Test data, t est samples and a new code identification areto be submitted with the request.Substance restrictions imposed by law, regulations or Ford, apply tothe materials addressed by this document. The restrictions aredefined in Engineering Materials Specification WSS-M99P9999-A1.4. APPROVAL O

16、F MATERIALSMat erials defined by this specification must have prior approval by theresp onsible Materials Engineering activity. Suppliers desiring approvalof thei r materials shall first obtain an expression of interest from theaffec ted Purchasing, Design and Materials Engineering activity. Uponreq

17、uest, the Supplier shall submit to the affected Materials Engineeringactivity a completed copy of their laboratory test reports, signed by aqualified and authorized representative of the test faci lity, demonstratingful l compliance with all the requirements of this specification (testresults, not n

18、ominal values), the material designation a nd code number, andtes t specimens for Ford evaluation. Fords engineering approval of amateri al will be based on its performance to this specification and on anassessment of suitability for intended processes and/or applications. Uponapprov al, the materia

19、l will be added to the Engineering Material ApprovedSource List.ENGINEERING MATERIAL SPECIFICATIONSK-M14J9561-A/B/C/DWP 3948-b Page 4 of 4 5. GENERAL INFORMATIONThe information given below is provided for assistance and clarificationand does not represent requirement(s) to this specification.5.1 FLASH POINT 21 C(ASTM D 56)5.2 DISTILLATION RANGE(ASTM D 1078)SK-M14J9561-A 105 - 141 CSK-M14J9561-B 105 - 160 CSK-M14J9561-C 112 - 146 CSK-M14J9561-D Not applicable5.3 EVAPORATION RESIDUE, max (SK-M14J9561-D only) 70 ppm(DIN 53172)5.4 WATER CONTENT, max (SK-M14J9561-D only) 0.65 %(DIN 51777)