FORD ESK-M14J233-A-2012 THINNER TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD ESK-M14J233-A-2012 THINNER TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD ESK-M14J233-A-2012 THINNER TO BE USED WITH FORD WSS-M99P1111-A .pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Release No. Released1994 12 19 Revised and Retyped was: 3 pages1985 03 12 SM/EQ5529 TP ReleasedWP 3948-a Page 1 of 2 THINNER ESK-M14J233-A1. SCOPEThe material defined by this specification is a thinner.2. APPLICATIONThis spe c

2、ification was originally released for material which is used todilute the primer for plastics, elastic ESK-M99J329-A.3. REQUIREMENTS3.1 COMPOSITIONBlend of glycolethers, alcohols and esters.3.2 DENSITY at 20 C 0.85 +/- 0.005 g/cm3(ASTM D 1298)3.3 DISTILLATION RANGE 82 - 137 C(ASTM D 1078)3.4 FLASH P

3、OINT 23 +/- 2 C(ASTM D 56)3.5 INDEX OF REFRACTION 1.4010 - 1.4022(ASTM D 1218)3.6 COLOR Water white3.7 SHELF STABILITYMinimum 12 months in the closed original container.3.8 SUBSTANCE CONTROLLegal, health, safety a nd environmental constraints may apply to themate rials which are submitted for approv

4、al to this specification.Refer to Engineering Material Specification SK-M99P9999-A.3.9 SUPPLIERS RESPONSIBILITYAll materials supplied to this specification must be equivalent inal l characteristics to the material upon which approval wasoriginally granted.ENGINEERING MATERIAL SPECIFICATIONMaterial N

5、ame Specification NumberDate Release No. Released1994 12 19 Revised and Retyped was: 3 pages1985 03 12 SM/EQ5529 TP ReleasedWP 3948-a Page 2 of 2 Pri or to making any change in the properties, composition,constr uction, color, processing or labeling of the materialorig inally approved under this spe

6、cification, whether or not suchchange s affect the materials ability to meet the specificationrequir ements, the Supplier shall notify Purchasing, Toxicology andthe affected Materials Engineering activity of the proposed changesand obtain the written approval of the Materials Engineeringactivity. Te

7、st data, t est samples and a new code identification areto be submitted with the request.Substance restrictions imposed by law, regulations or Ford, apply tothe materials addressed by this document. The restrictions aredefined in Engineering Materials Specification WSS-M99P9999-A1.4. APPROVAL OF MAT

8、ERIALSMat erials defined by this specification must have prior approval by theresp onsible Materials Engineering activity. Suppliers desiring approvalof thei r materials shall first obtain an expression of interest from theaffec ted Purchasing, Design and Materials Engineering activity. Uponrequest,

9、 the Supplier shall submit to the affected Materials Engineeringactivity a completed copy of their laboratory test reports, signed by aqualified and authorized representative of the test faci lity, demonstratingful l compliance with all the requirements of this specification (testresults, not nomina

10、l values), the material designation a nd code number, andtes t specimens for Ford evaluation. Fords engineering approval of amateri al will be based on its performance to this specification and on anassessment of suitability for intended processes and/or applications. Uponapprov al, the material will be added to the Engineering Material ApprovedSource List.