FORD ESF-M1L64-A-2003 COPPER WIRE BATTERY CABLE - # 2 GAGE TO BE USED WITH FORD WSS-M99P1111-A 《电池电缆用铜丝》.pdf

《FORD ESF-M1L64-A-2003 COPPER WIRE BATTERY CABLE - # 2 GAGE TO BE USED WITH FORD WSS-M99P1111-A 《电池电缆用铜丝》.pdf》由会员分享，可在线阅读，更多相关《FORD ESF-M1L64-A-2003 COPPER WIRE BATTERY CABLE - # 2 GAGE TO BE USED WITH FORD WSS-M99P1111-A 《电池电缆用铜丝》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2003 04 25 Revised Para 3.0 inserted; Para 3.9, 3.10, 3.11, 3.12, 3.13, 4 deleted 1991 01 31 DE00300107002086 Revised 3.3 std para added J. Huebner 1963 08 16 CTS4-58846-1 Released Orig./ s/ T.H. Meister Pri

2、nted copies are uncontrolled Page 1 of 2 Copyright 2003, Ford Global Technologies, Inc. COPPER WIRE, BATTERY CABLE - # 2 GAGE ESF-M1L64-A 1. SCOPE The material defined by this specification is a # 2 gage stranded, insulated battery cable. 2. APPLICATION This specification was released originally for

3、 material used for battery starting cables on heavy duty installations. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 CABLE SIZE The finished c

4、able diameter shall not exceed SAE limits for type SGR cable. 3.2 CABLE QUALITY Shall meet all the requirements listed herein and must be equal to the original approved samples. 3.3 CABLE CONSTRUCTION The cable shall consist of 210 strands (nominal) of # 25 gage round wire layed in rope construction

5、 and served with 25.4 x 0.08 mm minimum paper or polyester film insulating tape with 12 % minimum overlap. Absolute minimum number of strands at any one time to be 203. No individual group is to contain more than 20% of the total strands. Optional construction of this cable shall allow 259 strands (

6、nominal) of # 26 gage round wire. With 252 strands absolute minimum. Construction , serving and maximum strands per group are the same as previously described. Minimum area is 31.55 mm2.3.4 WIRE QUALITY The conductor strands prior to stranding or bunching shall consist of bare ESF-M2L1-A, soft or an

7、nealed round copper wire. ENGINEERING MATERIAL SPECIFICATION ESF-M1L64-A Page 2 of 2 Copyright 2003, Ford Global Technologies, Inc. 3.5 INSULATION COLOR Black, unless otherwise specified on the engineering drawing 3.6 INSULATION QUALITY The elastomer insulation must meet all basic SAE type SGR requi

8、rements and have nominal wall thickness of 1.42 mm. 3.7 RESISTIVITY AT 20 C, max 451 /m 3.8 PHYSICAL AND ELECTRICAL PROPERTIES Three samples of cable are required. One for each of the high temperature, low temperature and oil absorption tests. All samples are subjected to the dielectric breakdown te

9、st at the completion of there respective tests. These samples 0.6 m in length with 25 mm of insulation stripped from both ends. 3.8.1 High Temperature Resistance No fracture or splitting of the insulation Test Method: Suspend sample over a 254 mm mandrel with a 2.72 kg weight at each end. Soak at 12

10、1 +/- 2 C for 120 h in a circulating air oven. Cool to 23 +/- 2 C, remove the weight and bend the sample around the mandrel in a reverse direction at a rate not exceeding 1 turn per minute until a 180 bend is completed. 3.8.2 Low Temperature Resistance No fracture or splitting of the insulation Test

11、 Method: Reduce temperature of a straight piece of sample to -34 C at a rate not to exceed 68 C per minute. Hold for 3 h and then wrap around a 254 mm mandrel for 180 at a rate of 1 turn per 10 s. 3.8.3 Oil Absorption Resistance Cable dia shall not increase more than 15% nor shall the insulation fra

12、cture or split Test Method: Immerse sample to within 38 mm from the end into a solution of 50% kerosene and 50% SAE 10W engine oil for 20 h at 49 +/- 2 C. Wrap sample around a 254 mm mandrel for 180 3.8.4 Dielectric Resistance No rupture of the insulation Test Method : Join exposed ends of sample and immerse loop to within 150 mm of ends in a 5% salt bath (salt content by weight at 27 C). Soak 5 h and then apply 500 V (RMS) 60 cps (Hz) between sample conductor and salt bath for 1 minute.