FORD ESB-M99J315-A-2012 CHIP RESISTANT REPAIR COATING - TWO-COMPONENT URETHANE - PAINTABLE - LOW BAKE TO BE USED WITH FORD WSS-M99P1111-A 《抗剥落修复涂层 可涂装的低烘烤双组分尿烷 与福特WSS-M99P1111-A.pdf
《FORD ESB-M99J315-A-2012 CHIP RESISTANT REPAIR COATING - TWO-COMPONENT URETHANE - PAINTABLE - LOW BAKE TO BE USED WITH FORD WSS-M99P1111-A 《抗剥落修复涂层 可涂装的低烘烤双组分尿烷 与福特WSS-M99P1111-A.pdf》由会员分享,可在线阅读,更多相关《FORD ESB-M99J315-A-2012 CHIP RESISTANT REPAIR COATING - TWO-COMPONENT URETHANE - PAINTABLE - LOW BAKE TO BE USED WITH FORD WSS-M99P1111-A 《抗剥落修复涂层 可涂装的低烘烤双组分尿烷 与福特WSS-M99P1111-A.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 03 2012 02 16 N Status No replacements named N. Benipal, NA 2005 08 30 Revised Inserted 3.0; Deleted 3.1, 3.7 and 4 1983 08 02 Released CAN1-AF504174-1 (Reissue to correct Change No.) Controlled document at www.MATS Copyright 2012, Ford G
2、lobal Technologies, LLC Page 1 of 4 CHIP RESISTANT REPAIR COATING - TWO-COMPONENT ESB-M99J315-A URETHANE - PAINTABLE - LOW BAKE NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a sandable two-component urethane stone chip resistant coating with good paintability c
3、haracteristics. 2. APPLICATION This specification was released originally to repair small damaged areas of ESB-M99J311. The material, covered by a flash primer, shall be cured by either the enamel or the catalyzed enamel bake cycle. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS
4、Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 NOMENCLATURE The materials components shall be described as follows: Polyol base Hardener When the two components are mixed together, the resulting solution shall b
5、e described as the “blend“. 3.3 PHYSICAL PROPERTIES 3.3.1 Nonvolatile (FLTM BI 102-01) Polyol base 59 +/- 1% Hardener 70 +/- 1% Blend 63 +/- 1% 3.3.2 Weight per volume at 23 +/- 2 C (ASTM D 1475) Polyol base 1.65 +/- .01 kg/L Hardener 1.06 +/- .01 kg/L Blend 1.33 +/- .01 kg/L ENGINEERING MATERIAL SP
6、ECIFICATION ESB-M99J315-A Copyright 2012, Ford Global Technologies, LLC Page 2 of 4 3.3.3 Viscosity (ASTM D 562) Polyol base 110 +/- 5 KU Hardener 95 +/- 5 KU Blend 70 +/- 5 KU 3.3.4 Blending Ratio, by Volume Polyol base, parts 1.33 Hardener, parts 1.0 3.3.5 Pot Life of the Blend 1 h min The blend s
7、hall retain excellent sprayability characteristics. 3.3.6 Bake Requirements When catalyzed enamel is to be used, cover the blended stone chip coating with ESB-M6J65 flash primer prior to baking. When body enamel is to be used, cover the blended stone chip coating with ESB-M6J57 flash primer prior to
8、 baking. 3.4 FILM PROPERTIES 3.4.1 Dry Film Thickness Requirement 200 - 280 m 3.4.2 Sagging and Solvent Popping No sagging or solvent popping is allowable at 200 - 280 m dry film thickness. 3.4.3 Paintability No significant color shift, difference in orientation of metallic flakes (metallic paints)
9、or other objectionable appearance defects in the topcoat over the chip coating. 3.4.4 Leveling The chip resistant coating shall have an orange peel appearance similar to that of ESB-M99J311. 3.4.5 Dry Sanding Characteristics After baking, the chip resistant coating plus ESB-M6J57 flash primer shall
10、dry sand (using a new sheet of 280 grit stearate filled paper for each panel) smoothly without clogging the paper and with a minimum of sand scratches. The material shall be equivalent in all respects to current approved production coating applied and tested under identical conditions. 3.5 RESISTANC
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDESBM99J315A2012CHIPRESISTANTREPAIRCOATINGTWOCOMPONENTURETHANEPAINTABLELOWBAKETOBEUSEDWITHFORDWSSM99P1111A
链接地址:http://www.mydoc123.com/p-745782.html