ETSI TS 129 140-2008 Universal Mobile Telecommunications System (UMTS) Multimedia Messaging Service (MMS) MM10 interface based on Diameter protocol Stage 3《全球移动通信系统(UMTS) 多媒体信息服务(M.pdf

《ETSI TS 129 140-2008 Universal Mobile Telecommunications System (UMTS) Multimedia Messaging Service (MMS) MM10 interface based on Diameter protocol Stage 3《全球移动通信系统(UMTS) 多媒体信息服务(M.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 129 140-2008 Universal Mobile Telecommunications System (UMTS) Multimedia Messaging Service (MMS) MM10 interface based on Diameter protocol Stage 3《全球移动通信系统(UMTS) 多媒体信息服务(M.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 129 140 V6.4.0 (2008-04)Technical Specification Universal Mobile Telecommunications System (UMTS);Multimedia Messaging Service (MMS);MM10 interface based on Diameter protocol;Stage 3 (3GPP TS 29.140 version 6.4.0 Release 6)ETSI ETSI TS 129 140 V6.4.0 (2008-04) 1 3GPP TS 29.140 version 6.4.0

2、 Release 6 Reference RTS/TSGC-0429140v640 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Importan

3、t notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Po

4、rtable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Informat

5、ion on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part

6、may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2008. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade

7、 Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 129 140 V6.4.0 (2008-04) 2 3GPP TS 29.140 version 6.4.0 Release 6 Intellectual Property Rights IPRs essential or po

8、tentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essenti

9、al, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No

10、 guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership

11、Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identitie

12、s can be found under http:/webapp.etsi.org/key/queryform.asp. ETSI ETSI TS 129 140 V6.4.0 (2008-04) 3 3GPP TS 29.140 version 6.4.0 Release 6 Contents Intellectual Property Rights2 Foreword.2 Foreword.5 1 Scope 6 2 References 6 3 Definitions, symbols and abbreviations .6 3.1 Definitions6 3.2 Abbrevia

13、tions .7 4 Procedure Description 7 4.1. MM10 Interrogation Procedure7 4.1.1 Information Elements .8 4.1.2 Normal Operation .9 5 Use of the Diameter base protocol .9 5.1 Securing Diameter Messages .10 5.2 Accounting functionality10 5.3 Use of sessions .10 5.4 Transport protocol 10 5.5 Routing conside

14、rations .10 5.6 Advertising Application Support10 6 Diameter application for MM10 interface11 6.1 Command-Code values 11 6.1.1 Message-Process-Request (MPR) Command .11 6.1.2 Message-Process-Answer (MPA) Command .12 6.2 Result-Code AVP values12 6.2.1 Success12 6.2.2 Permanent Failures .12 6.2.3 Tran

15、sient Failures .12 6.3 AVPs 13 6.3.1 Served-User-Identity AVP13 6.3.2 MSISDN AVP 13 6.3.3 VASP-ID AVP13 6.3.4 VAS-ID AVP14 6.3.5 Trigger-Event AVP.14 6.3.6 3GGPP-IMSI 14 6.3.7 Sender-Address AVP14 6.3.8 Initial-Recipient-Address AVP.14 6.3.9 Result-Recipient-Address AVP 14 6.3.10 Sequence-Number AVP

16、15 6.3.11 Recipient-Address AVP15 6.3.12 Routeing-Address AVP 15 6.3.13 Originating-Interface AVP .15 6.3.14 Delivery-Report AVP .15 6.3.15 Read-Reply AVP 15 6.3.16 Sender-Visibility AVP16 6.3.17 Service-Key AVP .16 6.3.18 Billing-Information AVP16 6.3.19 Status AVP16 6.3.20 Status-Code AVP16 6.3.21

17、 Status-Text AVP.16 6.3.22 Routeing-Address-Resolution AVP17 6.4 Use of namespaces .17 6.4.1 AVP codes 17 ETSI ETSI TS 129 140 V6.4.0 (2008-04) 4 3GPP TS 29.140 version 6.4.0 Release 6 6.4.2 Experimental-Result-Code AVP values17 6.4.3 Command Code values .17 6.4.4 Application-ID value 17 7 Special R

18、equirements.17 7.1 Version Control 17 Annex A (informative): Change history .18 History 19 ETSI ETSI TS 129 140 V6.4.0 (2008-04) 5 3GPP TS 29.140 version 6.4.0 Release 6 Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the prese

19、nt document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z

20、 where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit

21、 is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 129 140 V6.4.0 (2008-04) 6 3GPP TS 29.140 version 6.4.0 Release 6 1 Scope The present document defines the procedures and the transport protocol for use in the Multimedia Messaging Service (MMS) based on

22、 Diameter. The present document is applicable to: - The MM10 interface between an MMS Relay/Server and the MSCF. Whenever it is possible this document specifies the requirements for this protocol by reference to specifications produced by the IETF within the scope of Diameter. Where this is not poss

23、ible, extensions to Diameter are defined within this document. 2 References The following documents contain provisions, which through reference in this text constitute provisions of the present document. - References are either specific (identified by date of publication, edition number, version num

24、ber, etc.) or non-specific. - For a specific reference, subsequent revisions do not apply. - For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that do

25、cument in the same Release as the present document. 1 3GPP TS 23.140 Release 6: “Multimedia Messaging Service (MMS); Functional description; Stage 2“. 2 3GPP TS 33.210: “3G Security; Network Domain Security; IP Network Layer Security“. 3 IETF RFC 2960: “Stream Control Transmission Protocol“. 4 IETF

26、RFC 3588: “Diameter Base Protocol“. 5 IETF RFC 2234: “Augmented BNF for syntax specifications“. 6 Open Mobile Alliance; OMA-MMS-ENC-v1_2-20030915-C; Multimedia Messaging Service; Encapsulation Protocol, Version 1.2 7 3GPP TS 29.229: “Cx and Dx interfaces based on the Diameter protocol; Protocol deta

27、ils“ 8 3GPP TS 23.003: “Numbering, addressing and identification“ 9 IETF RFC 2960: “Stream Control Transmission Protocol“. 10 IETF RFC 3309: “Stream Control Transmission Protocol (SCTP) Checksum Change“. 11 3GPP TS 29.329: “Sh Interface based on the Diameter protocol; Protocol details“. 12 3GPP TS 2

28、9.061: “Interworking between the Public Land Mobile Network (PLMN) supporting packet based services and Packet Data Networks (PDN)“. 3 Definitions, symbols and abbreviations 3.1 Definitions Refer to IETF RFC 3588 4 for the definitions of some terms used in this document. ETSI ETSI TS 129 140 V6.4.0

29、(2008-04) 7 3GPP TS 29.140 version 6.4.0 Release 6 For the purposes of the present document, the following terms and definitions apply. Messaging Service Control Function: An network element or functional entity hosting network operator specific services in order to enhance the capabilities of the M

30、MS. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AAA Authentication, Authorization and Accounting AS Application Server ABNF Augmented Backus-Naur Form AVP Attribute-Value Pair IANA Internet Assigned Numbers Authority IETF Internet Engineering Task F

31、orce MSCF Messaging Service Control Function NDS Network Domain Security RFC Request For Comment SCTP Stream Control Transport Protocol UCS Universal Character Set URL Uniform Resource Locator UTF UCS Transformation Formats 4 Procedure Description In the tables that describe the information elements

32、 transported by each command, each Information Element is marked as (M) Mandatory, (C) Conditional or (O) Optional. A mandatory information element shall always be present. A conditional information shall be present if certain conditions are fulfilled; if those conditions are not fulfilled it shall

33、be absent. An optional information element may be present or absent in the command, at the discretion of the application at the sending entity. The classification of information elements on application level is provided in 3GPP TS 23.140 1. The present document provides the classification on protoco

34、l level, which may differ from the application requirements. 4.1. MM10 Interrogation Procedure This procedure is used between the MMS Relay/Server and the MSCF. This procedure is invoked by the MMS Relay/Server and is used to request processing of addressing information related to a multimedia messa

35、ge (see 3GPP TS 23.140 1). This procedure is mapped to the commands Message-Process-Request/Answer in the Diameter application specified in section 6.1. Tables 4.1.1.1 and 4.1.1.2 detail the involved information elements. ETSI ETSI TS 129 140 V6.4.0 (2008-04) 8 3GPP TS 29.140 version 6.4.0 Release 6

36、 4.1.1 Information Elements Table 4.1.1.1: MM10 Interrogation Request Information element name Mapping to Diameter AVP Cat. Description Message Type Diameter Command Code M Identification of the MM10 message. Trigger Event Trigger-Event M Identification of the event leading to invocation of the MM10

37、 interrogation Served User Identity Served-User-Identity M This information element contains the identification of the served user. Served User IMSI 3GPP-IMSI C This information element contains the identity of the mobile subscriber (IMSI). This element shall be present if received via the access. I

38、nitial Recipient Address Initial-Recipient-Address M This information element contains the recipients of a multimedia message as requested by the sender. In case of multiple recipients multiple occurrences of this information element shall apply. Originating Interface Origination Interface M This in

39、formation element identifies the interface the multimedia message has been received on. Service Key Service-Key C This information element contains identification of the application on the MSCF. It shall be present if the MMS Relay/Server trigger configuration contains this information. Sender Addre

40、ss Sender-Address C This information element contains the identity of the sender to be presented to the recipient. This information element shall be available if contained in the multimedia message. Delivery Report Delivery-Report C This information contains information about the users request for d

41、elivery reports. This information element shall be present if the request has been received in the multimedia message. Read Reply Read-Reply C This information contains information about the users request for read reply reports. This information element shall be present if the request has been recei

42、ved in the multimedia message. Sender Visibility Sender-Visibility C This information element contains information about the users request to hide the own identity. This information element shall be present if the request has been received in the multimedia message. ETSI ETSI TS 129 140 V6.4.0 (2008

43、-04) 9 3GPP TS 29.140 version 6.4.0 Release 6 Table 4.1.1.2: MM10 Interrogation Response Information element name Mapping to Diameter AVP Cat. Description Message Type Diameter Command Code M Identification of the MM10 message. Result-Code M This information element contains the result of the operat

44、ion. Status-Code O This information element contains message status information to notify the served user about the outcome of the message processing. Result Code Status-Text O This information element contains an unstructured response status text to qualify the outcome of the message processing. Pr

45、esentation Address Recipient-Address O This information element contains the recipient address for presentation resulting from the MSCF processing. Routeing Address Routeing-Address O This information element contains the recipient address for routeing resulting from the MSCF processing. Sender Addr

46、ess Sender-Address O This information element contains the sender address information resulting from the MSCF processing. Routeing Address Resolution Routeing-Address-Resolution C This information element indicates whether the Routeing-Address contains a resolved or unresolved address. This informat

47、ion element shall be present if Routeing-Address is present, otherwise absent. Delivery Report Delivery-Report O This information element contains the delivery report request information resulting from the MSCF processing. Sender Visibility Sender-Visibility O This information element contains the s

48、ender visibility request information resulting from the MSCF processing. Read Reply Read-Reply O This information element contains the read reply request information resulting from the MSCF processing. CDR Information Billing-Information O This information element contains transparent billing data r

49、esulting from the MSCF processing. 4.1.2 Normal Operation If the MMS Relay/Server sends MM10 interrogation request to the MSCF after it has detected that a multimedia message is subject to processing in the MSCF. The MM10 interrogation request contains the message data as received from the served user. A MM10 interrogation response received from the MSCF shall be composed as follows: square4 If the MM10 interrogation response contains a DIAMETER_SUCCESS result code, then the MSCF has authorised the message request unconditionally. The MMS Relay/Ser