ETSI TS 103 544-18-2017 Publicly Available Specification (PAS) Intelligent Transport Systems (ITS) MirrorLink Part 18 IEEE 802 11 Car Connectivity Consortium (CCC) Information Elem.pdf

《ETSI TS 103 544-18-2017 Publicly Available Specification (PAS) Intelligent Transport Systems (ITS) MirrorLink Part 18 IEEE 802 11 Car Connectivity Consortium (CCC) Information Elem.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 103 544-18-2017 Publicly Available Specification (PAS) Intelligent Transport Systems (ITS) MirrorLink Part 18 IEEE 802 11 Car Connectivity Consortium (CCC) Information Elem.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 103 544-18 V1.3.0 (2017-10) Publicly Available Specification (PAS); Intelligent Transport Systems (ITS); MirrorLink; Part 18: IEEE 802.11Car Connectivity Consortium (CCC) Information Element CAUTION The present document has been submitted to ETSI as a PAS produced by CCC and approved by the

2、 ETSI Technical Committee Intelligent Transport Systems (ITS). CCC is owner of the copyright of the document CCC-TS-050 and/or had all relevant rights and had assigned said rights to ETSI on an “as is basis“. Consequently, to the fullest extent permitted by law, ETSI disclaims all warranties whether

3、 express, implied, statutory or otherwise including but not limited to merchantability, non-infringement of any intellectual property rights of third parties. No warranty is given about the accuracy and the completeness of the content of the present document. TECHNICAL SPECIFICATION ETSI ETSI TS 103

4、 544-18 V1.3.0 (2017-10)2 Reference DTS/ITS-88-18 Keywords interface, ITS, PAS, smartphone ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfectur

5、e de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be mod

6、ified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

7、Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please s

8、end your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permissi

9、on of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2017. Car Connectivity Consortium 2011-2017. All rights reserved. ETSI logo is a Trade Mark of ETSI regist

10、ered for the benefit of its Members. MirrorLink is a registered trademark of Car Connectivity Consortium LLC. RFB and VNC are registered trademarks of RealVNC Ltd. UPnP is a registered trademark of UPnP Forum. Other names or abbreviations used in the present document may be trademarks of their respe

11、ctive owners. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Member

12、s. GSM and the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI TS 103 544-18 V1.3.0 (2017-10)3 Contents Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Abb

13、reviations . 5g34 IEEE 802.11 Information Element . 6g35 CCC Information Element 6g35.1 General . 6g35.2 MirrorLink Subelements 7g35.2.1 General 7g35.2.2 MirrorLink UPnP Device Information Subelement 7g35.2.3 Internet Accessibility Subelement 8g3Annex A (informative): Authors and Contributors . 9 g3

14、History 10g3ETSI ETSI TS 103 544-18 V1.3.0 (2017-10)4 Intellectual Property Rights Essential patents IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and

15、non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/).

16、Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present

17、 document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or

18、tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Intelligent Transport Systems (I

19、TS). The present document is part 18 of a multi-part deliverable. Full details of the entire series can be found in part 1 i.1. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interprete

20、d as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 103 544-18 V1.3.0 (2017-10)5 1 Scope The present document is part of the MirrorLinkspe

21、cification which specifies an interface for enabling remote user interaction of a mobile device via another device. The present document is written having a vehicle head-unit to interact with the mobile device in mind, but it will similarly apply for other devices, which provide a color display, aud

22、io input/output and user input mechanisms. IEEE allows defining vendor-specific Information elements, which are used to carry information not defined in the IEEE standard within a single defined format. The IE (Information Element) is located at the end of management frames, such as the beacon frame

23、 defined in 802.11 specification of IEEE 1. Multiple IEs can be concatenated. Based on the usage of IE, IEEE defines the formats of different kinds of IEs identified by the Element ID. The present document specifies the IEEE 802.11 CCC vendor-specific Information Element. 2 References 2.1 Normative

24、references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applie

25、s. Referenced documents which are not found to be publicly available in the expected location might be found at https:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long-term validity. The following re

26、ferenced documents are necessary for the application of the present document. 1 IEEE Std. 801.11-2012TM: “Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications“, March 29, 2012. 2.2 Informative references References are either specific (identified by date of publi

27、cation and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at th

28、e time of publication, ETSI cannot guarantee their long-term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI TS 103 544-1 (V1.3.0): “Publicly Available Specification

29、 (PAS); Intelligent Transport Systems (ITS); MirrorLink; Part 1: Connectivity“. 3 Abbreviations For the purposes of the present document, the following abbreviations apply: CCC Car Connectivity Consortium IE Information Element IEEE Institute of Electrical and Electronics Engineers ETSI ETSI TS 103

30、544-18 V1.3.0 (2017-10)6 Miracast Commercial denomination of WDF ML MirrorLink OUI Organizationally Unique Identifier UPnP Universal Plug and Play USB Universal Serial Bus 4 IEEE 802.11 Information Element The IE (Information Element) is located at the end of management frames such as the beacon fra

31、me defined in 802.11 specification of IEEE 1. Multiple IEs can be concatenated. Based on the usage of IE, IEEE defines the formats of different kinds of IEs identified by the Element ID. The IEEE 802.11 Information Element format is given in Table 1. Table 1: IEEE 802.11 Information Element Format F

32、ield Size (octet) Value Description Element ID 1 Defined in 1 Element identifier Length 1 Variable Length of sum of following elements Information Variable Information (IE specific) IEEE allows the definition of vendor-specific information elements, identified by the Element ID of 0xDD. 5 CCC Inform

33、ation Element 5.1 General The format of the CCC Information Element is given in Table 2. Table 2: MirrorLink Information Element Format Field Size (octet) Value Description Element ID 1 0xDD 802.11 Vendor specific usage Length 1 Variable The length of sum of following elements OUI (Organizationally

34、Unique Identifier) 3 04-DF-69 CCC specific OUI assigned by IEEE OUI Type 1 OUI type Subelements Variable One or more subelements can follow The Organizationally Unique Identifier (OUI) of the CCC Information Element shall be 0x04DF69. Allowed OUI Type values are given in Table 3. Table 3: OUI Types

35、OUI Type (Decimal) Note 0-9 Reserved for future use 10 MirrorLink 1.211 irrorLink 1.312-255 Reserved for future use All MirrorLink subelements, as specified below, shall be available, unchanged, within future OUI types (i.e. within currently reserved OUI types). ETSI ETSI TS 103 544-18 V1.3.0 (2017-

36、10)7 5.2 MirrorLink Subelements 5.2.1 General The MirrorLink Subelement format is given in Table 4. Table 4: MirrorLink Subelement Format Field Size (octet) Value Description Subelement ID 1 Identifier which represents the type of subelement (See Table 5). Length 1 Variable The length of sum of foll

37、owing elements Subelement body field variable The value of subelement. The Subelement ID shall have a value which represents the type of the Subelement. Allowed values are defined in Table 5. Table 5: Subelement Identifier Subelement ID (Decimal) Note 0 MirrorLink UPnP device information 1 Internet

38、Accessibility2-255 Reserved5.2.2 MirrorLink UPnP Device Information Subelement The MirrorLink Device Information subelement is given in Table 6. The Subelement ID field shall have a value of 0x00. Table 6: MirrorLink UPnP Device Information Subelement Field Size (octet) Value Description Subelement

39、ID 1 0x00 Identifier which indicates subelement type of UPnP device information of MirrorLink device. Length 1 4 The length of sum of following elements MirrorLink UPnP Device Information 4 The value of MirrorLink UPnP Device Information (See Table 7). The format of the MirrorLink UPnP Device Inform

40、ation field is given in Table 7. Table 7: MirrorLink UPnP Device Information Format Bits Name Interpretation 2:0 UPnP Device Type 0x0: UPnP TmServerDevice:1 Server 0x1: UPnP TmServerDevice:1 Control Point 0x2 0x7: Reserved 3 TmApplicationServer:1 Service 0b0: Not supported 0b1: Supported 4 TmClientP

41、rofile:1 Service 0b0: TmClientProfile not supported 0b1: TmClientProfile supported 5 TmNotificationServer:1 Service 0b0: TmNotificationServer not supported 0b1: TmNotificationServer supported 15:6 Reserved Reserved for additional services ETSI ETSI TS 103 544-18 V1.3.0 (2017-10)8 Bits Name Interpret

42、ation 31:16 Port number Port number, used to make URL for UPnP device description fetching Shall be 0 (zero) in case of a MirrorLink Client sending the Information Element. The UPnP Device Information subelement shall be included within the CCC Information Element, if the MirrorLink device is provid

43、ing any MirrorLink functionality over Wi-Fi. 5.2.3 Internet Accessibility Subelement The Internet Accessibility subelement is given in Table 6. The Subelement ID field shall have a value of 0x01. Table 8: Internet Accessibility Subelement Field Size (octet) Value Description Subelement ID 1 0x01 Ide

44、ntifier which indicates subelement type of Internet Accessibility. Length 1 2 Length of sum of following elements Internet Accessibility 2 Value of Internet Accessibility (See Table 9) The format of the Internet Accessibility Information field is given in Table 7. Table 9: Internet Accessibility Inf

45、ormation Format Bits Name Interpretation 1:0 MirrorLink Type 0b00: MirrorLink Server 0b01; MirrorLink Client with support for single ML Server 0b10: Reserved 0b11: MirrorLink Client with support for multiple ML Servers 2 Internet Access Support 0b0: Not supported 0b1: Supported 3 Internet Access Req

46、uired 0b0: Not required 0b1: Required 7:4 Reserved 15:8 MirrorLink Client Preference MirrorLink Clients preference in case where GO role conflict happens; 0x00: No conflict or not a MirrorLink Client 0x01: Internet Access Required 0x02: Multiple MirrorLink Server Support The Internet Accessibility I

47、nformation subelement may be included within the CCC Information Element, if the MirrorLink device is providing MirrorLink functionality over Wi-Fi. In case the Internet Accessibility Information subelement is missing from the CCC Information Element, the receiving MirrorLink device should implement

48、 a behavior as if the following default values had been received: ML Type: 0b00 or 0b01 (dependent on MirrorLink device type) Internet Access Support: 0b0 (Not supported) Internet Access Required: 0b0 (Not required) ML Client Preference: 0b00 (No conflict or not a MirrorLink Client) ETSI ETSI TS 103

49、 544-18 V1.3.0 (2017-10)9 Annex A (informative): Authors and Contributors The following people have contributed to the present document: Rapporteur: Dr. Jrg Brakensiek, E-Qualus (for Car Connectivity Consortium LLC) Other contributors: Mingoo Kim, LG Electronics Jungwoo Kim, LG Electronics Sungjin Park, Samsung Electronics Sungjin Lee, LG Electronics ETSI ETSI TS 103 544-18 V1.3.0 (2017-10)10 History Document history V1.3.0 October 2017 Publication