ETSI TS 103 429-2016 Integrated broadband cable telecommunication networks (CABLE) Cable Customer Premises Equipment (CPE) with Integrated Radio and Non-Radio Interfaces Technical ch.pdf

《ETSI TS 103 429-2016 Integrated broadband cable telecommunication networks (CABLE) Cable Customer Premises Equipment (CPE) with Integrated Radio and Non-Radio Interfaces Technical ch.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 103 429-2016 Integrated broadband cable telecommunication networks (CABLE) Cable Customer Premises Equipment (CPE) with Integrated Radio and Non-Radio Interfaces Technical ch.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 103 429 V1.1.1 (2016-07) Integrated broadband cable telecommunication networks (CABLE); Cable Customer Premises Equipment (CPE) with Integrated Radio and Non-Radio Interfaces; Technical Specification covering the cable equipment technical requirements in support of Harmonised Standards for

2、the essential requirements of article 3.1b of the Directive 2014/53/EU TECHNICAL SPECIFICATION ETSI ETSI TS 103 429 V1.1.1 (2016-07)2 Reference DTS/CABLE-00023 Keywords CABLE ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 34

3、8 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The cont

4、ent of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Docu

5、ment Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.or

6、g/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mecha

7、nical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications

8、 Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM lo

9、go are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 103 429 V1.1.1 (2016-07)3 Contents Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g3Introduction 4g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 7g33 Definition

10、s and abbreviations . 8g33.1 Definitions 8g33.2 Abbreviations . 8g34 Overview of Types of Cable Equipment 9g35 Relevant Receiver and Transmitter Parameters . 10g35.1 Non-radio function . 10g35.2 Radio Function . 12g36 Primary and Secondary network interfaces 12g36.1 General . 12g36.2 Functional repr

11、esentation of the cable equipment 13g37 Test and Measurements 14g37.1 Introduction 14g37.2 Test configuration. 14g37.3 Measurements . 15g37.3.1 General 15g37.3.2 Emission Measurements . 15g37.3.3 Immunity Measurements 15g3Annex A (informative): Bibliography . 16g3History 17g3ETSI ETSI TS 103 429 V1.

12、1.1 (2016-07)4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intell

13、ectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, includ

14、ing IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has

15、 been produced by ETSI Technical Committee Integrated broadband cable telecommunication networks (CABLE). Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clau

16、se 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction In 2014 the new Radio Equipment directive has been published by the EU commission (Radio Equipment Directive

17、 2014/53/EU, OJ L153 22 May 2014 i.1). This directive will replace the existing Radio 12thJune 2016 is the date by when Member States are required to implement RED i.1 into their national laws; July 2017 is a transition period for RED i.1 during which period the RTTED i.2 may still be used i.e. one

18、year transition period. A new product entering the market after the 13thJune 2016 is required to meet the requirements of RED i.1. The RED i.1 is replacing the RTTED i.2, however as the name implies, RTTE has become RE (no more TTE) therefore Telecom Terminal Equipment (TTE), has been removed from t

19、he Radio Equipment Directive: Cable modems and cable receiver equipment with a non-radio network interface i.e. fixed line cable RF network interface, will continue to have to comply with all other applicable Directives. In terms of the Directives EMC i.3 and LVD i.4. New LVD i.4 and EMC Directives

20、i.3 apply from 20 April 2016. ETSI ETSI TS 103 429 V1.1.1 (2016-07)5 NOTE: DOCSISis a registered Trade Mark of Cable Television Laboratories, Inc., and is used in the present document with permission. ETSI ETSI TS 103 429 V1.1.1 (2016-07)6 1 Scope The present document provides technical requirements

21、 for cable CPE with integrated radio and non-radio interfaces in support of Harmonised Standards for the essential requirements of article 3.1b of the Radio Equipment Directive 2014/53/EU i.1. Cable equipment comprises integrated non-radio and radio network interfaces. These functions are integrated

22、 either on the same integrated electronic components on the same printed circuit board or by separate integrated components on the same printed circuit boards but housed in the same equipment enclosure. The non-radio function is the Cable RF as specified by ETSI EN 302 878-2 1 for data communication

23、 services and by ETSI EN 300 429 2 for video communication services. The radio function is a wireless local area network operating in the 2,4 GHz and 5 GHz frequency bands according to IEEE 802.11 3. NOTE: Cable equipment does not comprise separate radio and non-radio products that are combined in o

24、ne enclosure. Where cable equipment of this type exist then the essential requirements of article 3.1b of Directive 2014/53/EU i.1 apply to the equipment and the equipment requirements are as specified by ETSI draft harmonised standard ETSI EN 303 446-1 i.5, at the time of writing it is under develo

25、pment ETSI TC ERM WGEMC. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the r

26、eferenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot g

27、uarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI EN 302 878-2: “Access, Terminals, Transmission and Multiplexing (ATTM); Third Generation Transmission Systems for Interactive Cable Television Services - IP Cable M

28、odems; Part 2: Physical Layer; DOCSIS 3.0“. 2 ETSI EN 300 429: “Digital Video Broadcasting (DVB); Framing structure, channel coding and modulation for cable systems“. 3 IEEE 802.11-2012: “IEEE Standard for Information Technology - Telecommunications and information exchange between systems - Local a

29、nd metropolitan area networks - Specific requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications“. 4 ETSI EN 302 878-3: “Access, Terminals, Transmission and Multiplexing (ATTM); Third Generation Transmission Systems for Interactive Cable Television Se

30、rvices - IP Cable Modems; Part 3: Downstream Radio Frequency Interface; DOCSIS 3.0“. 5 CENELEC EN 60728-1: “Cable networks for television signals, sound signals and interactive services - Part 1: System performance of forward paths“. 6 ETSI EN 301 489-1: “ElectroMagnetic Compatibility (EMC) standard

31、 for radio equipment and services; Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU and the essential requirements of article 6 of the Directive 2014/30/EU; Part 1: Common technical requirements“. ETSI ETSI TS 103 429 V1.1.1 (2016-07)7 7 ETSI EN 3

32、01 489-17: “ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for Broadband Data Transmission Systems; Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU“. 2.2 Informative references Referenc

33、es are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any

34、hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive

35、2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 Directive 1999/5/EC of the European Parliament and of the Council o

36、f 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity. i.3 Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic com

37、patibility (recast). i.4 Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits (recast). i.5 ET

38、SI EN 303 446-1: “ElectroMagnetic Compatibility (EMC) Standard for radio equipment and services; Part 60: Specific conditions for combined radio and non-radio equipment in the domestic environment. Harmonised Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU“

39、. i.6 IEEE 802.11b: “IEEE Standard for Information Technology - Telecommunications and information exchange between systems - Local and Metropolitan area networks - Specific requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) specifications: Higher Speed Physica

40、l Layer (PHY) Extension in the 2.4 GHz band“. i.7 IEEE 802.11g: “IEEE Standard for Information Technology - Telecommunications and information exchange between systems - Local and Metropolitan Area Networks - Specific Requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Laye

41、r (PHY) Specifications: Further Higher Data Rate Extension in the 2.4 GHz Band“. i.8 IEEE 802.11n: “IEEE Standard for Information technology - Local and metropolitan area networks - Specific requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications Amen

42、dment 5: Enhancements for Higher Throughput“. i.9 IEEE 802.11a: “IEEE Standard for Information Technology - Telecommunications and information exchange between systems - Local and Metropolitan area networks - Specific requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Laye

43、r (PHY) specifications: High Speed Physical Layer in the 5 GHz band“. i.10 CM-SP-CMCIv3.0-I02-140729: “Cable Modem to Customer Premise Equipment Interface Specification“. i.11 ETSI TS 103 161-14: “Access, Terminals, Transmission and Multiplexing (ATTM); Integrated Broadband Cable and Television Netw

44、orks; IPCablecom 1.5; Part 14: Embedded MTA Analog Interface and Powering Specification“. ETSI ETSI TS 103 429 V1.1.1 (2016-07)8 i.12 IEEE 802.11ac: “IEEE Standard for Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specif

45、ic requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications - Amendment 4: Enhancements for Very High Throughput for Operation in Bands below 6 GHz“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the followin

46、g terms and definitions apply: Bluetooth system: equipment in compliance with Bluetooth specification NOTE: BluetoothTMis an example of a suitable product available commercially. This information is given for the convenience of users of the present document and does not constitute an endorsement by

47、ETSI of this product. combined equipment: any combination of non-radio equipment that requires a plug-in radio device to offer full functionality Cable Equipment: cable modem and cable receiver (analogue or digital) within the domestic environment Cable Equipment with integrated radio and non-radio

48、functions: cable equipment with a DOCSIS1 and/or DVB-C 2 transceiver and a wireless LAN IEEE 802.11 3 operating in the 2,4 GHz and 5 GHz frequency bands with their functions integrated either on the same integrated electronic components on the same printed circuit board or by separate integrated com

49、ponents on the same printed circuit boards but housed in the same equipment enclosure Customer Premises Equipment (CPE): equipment at the end users premises; may be provided by the end user or the service provider Decibels (dB): logarithmic unit used to express the ratio of two values of a physical quantity Decibel-Millivolt (dBmV): dB measurement system wherein 0 dBmV is defined as 1 millivolt over 75 g3MOCA 2.0: set of standards developed by Multimedia Over Coax Allian