ETSI TS 102 593-2008 Methods for Testing and Specification (MTS) Internet Protocol Testing (IPT) IPv6 Security Conformance Test Suite Structure and Test Purposes (TSS&TP)《测试方法和规范(M_1.pdf
《ETSI TS 102 593-2008 Methods for Testing and Specification (MTS) Internet Protocol Testing (IPT) IPv6 Security Conformance Test Suite Structure and Test Purposes (TSS&TP)《测试方法和规范(M_1.pdf》由会员分享,可在线阅读,更多相关《ETSI TS 102 593-2008 Methods for Testing and Specification (MTS) Internet Protocol Testing (IPT) IPv6 Security Conformance Test Suite Structure and Test Purposes (TSS&TP)《测试方法和规范(M_1.pdf(46页珍藏版)》请在麦多课文档分享上搜索。
1、 ETSI TS 102 593 V1.2.0 (2008-04)Technical Specification Methods for Testing and Specification (MTS);Internet Protocol Testing (IPT);IPv6 Security;Conformance Test Suite Structure andTest Purposes (TSS Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is
2、 available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not ref
3、erenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Methods for Testing and Specification (MTS). ETSI ETSI TS 102 593 V1.2.0
4、 (2008-04) 5 1 Scope The purpose of the present document is to provide Test Suite Structure and Test Purposes (TSS - for informative references. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. For online re
5、ferenced documents, information sufficient to identify and locate the source shall be provided. Preferably, the primary source of the referenced document should be cited, in order to ensure traceability. Furthermore, the reference should, as far as possible, remain valid for the expected life of the
6、 document. The reference shall include the method of access to the referenced document and the full network address, with the same punctuation and use of upper case and lower case letters. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
7、their long term validity. 2.1 Normative references The following referenced documents are indispensable for the application of the present document. For dated references, only the edition cited applies. For non-specific references, the latest edition of the referenced document (including any amendme
8、nts) applies. 1 ETSI TS 102 351: “Methods for Testing and Specification (MTS); Internet Protocol Testing (IPT); IPv6 Testing: Methodology and Framework“. 2 ETSI TS 102 558: “Methods for Testing and Specification (MTS); Internet Protocol Testing (IPT): IPv6 Security; Requirements Catalogue“. 3 ISO/IE
9、C 9646-1: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 4 ISO/IEC 9646-2: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 2: Abstract Test Suite specifi
10、cation“. 5 ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. ETSI ETSI TS 102 593 V1.2.0 (2008-04) 6 2.2 Informative references The following referenced documents are not essential to the use of the
11、present document but they assist the user with regard to a particular subject area. For non-specific references, the latest version of the referenced document (including any amendments) applies. Not applicable. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document,
12、 the following terms and definitions apply: abstract test case: Refer to ISO/IEC 9646-1 3. Abstract Test Method (ATM): Refer to ISO/IEC 9646-1 3. Abstract Test Suite (ATS): Refer to ISO/IEC 9646-1 3. Implementation Under Test (IUT): Refer to ISO/IEC 9646-1 3. Lower Tester (LT): Refer to ISO/IEC 9646
13、-1 3. Test Purpose (TP): Refer to ISO/IEC 9646-1 3. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AH Authentication Header ATM Abstract Test Method ATS Abstract Test Suite ESP Encapsulating Security Payload ICV Integrity Check Value IETF Internet Engi
14、neering Task Force IKE Internet Key Exchange IPv6 Internet Protocol version 6 IUT Implementation Under Test LT Lower Test RC Requirements Catalogue RQ Requirement TP Test Purpose TSS Test Suite Structure UDP User Datagram Protocol 4 Test Suite Structure (TSS) Test Purposes have been written for IPv6
15、 mobile nodes, correspondent nodes and home agents according to the Requirements (RQ) of the Requirements Catalogue (RC) in TS 102 558 2. Test purposes have been written for behaviours requested with “MUST“ or “SHOULD“, optional behaviour described with “MAY“ or similar wording indicating an option
16、has not been turned into test purposes. The test purposes have been divided into three groups: Group 1: Authentication Header (AH) Group 2: Encapsulating Security Payload (ESP) ETSI ETSI TS 102 593 V1.2.0 (2008-04) 7 Group 3: Key Exchange (IKEv2) Protocol The sub-grouping of these three groups follo
17、ws the structure of the RC. Group 1: Authentication Header (AH) Group 2: Encapsulating Security Payload (ESP) Group 3: Key Exchange (IKEv2) Protocol Group 3.1 Exchange Message Structures Group 3.2 IKE Header and Payload Formats Group 3.2.1 Configuration payload Group 3.2.2 IKE Error Types Group 3.3
18、IKE Informational Exchanges Group 3.4 IKE Protocol Group 3.4.1 Authentication Group 3.4.1.1 Extensible Authentication Methods Group 3.4.2 Error Handling Group 3.4.3 General Protocol Handling Group 3.4.3.1 Address and Port Agility Group 3.4.3.2 IP Compression (IPComp) Group 3.4.3.3 Message Format Gro
19、up 3.4.3.4 Overlapping Requests Group 3.4.3.5 Request Internal Address Group 3.4.3.6 Retransmission Timers Group 3.4.3.7 Version Compatibility Group 3.4.4 Security Parameter Negotiation Group 3.4.4.1 Algorithm Negotiation Group 3.4.4.2 Cookies Group 3.4.4.3 Rekeying Group 3.4.4.4 Traffic Selector Ne
20、gotiation ETSI ETSI TS 102 593 V1.2.0 (2008-04) 8 Annex A (normative): Test Purposes (TP) The test purposes have been written in the formal notation TPlan as described in annex A of TS 102 351 1. This original textual output ASCII file (SEC.tplan) is contained in archive ts_102593v010102p0.zip which
21、 accompanies the present document. The raw text file has been converted to a table format in this annex to allow better readability. The two formats shall be considered equivalent. In the event that there appears to be syntactical or semantic differences between the two then the textual TPlan repres
22、entation takes precedence over the table format in this annex. A.1 Authentication Header (AH) Test Purpose Identifier: TP_SEC_2000_01 Summary: Test of generating first unicast IPv6 packets with Authentication Header References: RQ_002_2000, RQ_002_2006, RQ_002_2011, RQ_002_2013, RQ_002_2015, RQ_002_
23、2017, RQ_002_2027, RQ_002_2032, RQ_002_2033, RQ_002_2034, RQ_002_2036 IUT Role: Ipsec_host Test Case: TC_SEC_2000_01 with IUT and destination_node established in an AH_security_association ensure that when IUT is requested to send first unicast IPv6Packet containing Authentication_Header then IUT se
24、nds IPv6Packet containing next_header_field of previous_header set to 51 and containing (Authentication_Header containing Security_Parameters_Index set to Security_Parameters_Index received from destination_node during SA_establishment and containing sequence_number set to 1 and containing correctly
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ETSITS1025932008METHODSFORTESTINGANDSPECIFICATIONMTSINTERNETPROTOCOLTESTINGIPTIPV6SECURITYCONFORMANCETESTSUITESTRUCTUREANDTESTPURPOSESTSSTP

链接地址:http://www.mydoc123.com/p-739266.html