ETSI TS 102 147-2-1-2004 Broadband Radio Access Networks (BRAN) HIPERACCESS Conformance testing for the Cell based Convergence Layer Part 2 UNI Service Specific Convergence Sublaye_1.pdf

《ETSI TS 102 147-2-1-2004 Broadband Radio Access Networks (BRAN) HIPERACCESS Conformance testing for the Cell based Convergence Layer Part 2 UNI Service Specific Convergence Sublaye_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 147-2-1-2004 Broadband Radio Access Networks (BRAN) HIPERACCESS Conformance testing for the Cell based Convergence Layer Part 2 UNI Service Specific Convergence Sublaye_1.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 147-2-1 V1.2.1 (2004-04)Technical Specification Broadband Radio Access Networks (BRAN);HIPERACCESS;Conformance testing for the Cell based Convergence Layer;Part 2: UNI Service Specific Convergence Sublayer (SSCS);Sub-part 1: Protocol Implementation ConformanceStatement (PICS) proformaET

2、SI ETSI TS 102 147-2-1 V1.2.1 (2004-04) 2 Reference RTS/BRAN-0034T03-2-1R1 Keywords access, ATM, broadband, hiperaccess, radio PICS, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Associ

3、ation but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or pe

4、rceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document shoul

5、d be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notifi

6、cation No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered f

7、or the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 147-2-1 V1.2.1 (2004-04) 3

8、Contents Intellectual Property Rights4 Foreword.4 Introduction 4 1 Scope 5 2 References 5 3 Definitions and abbreviations.5 3.1 Definitions5 3.2 Abbreviations .6 4 Conformance to this PICS proforma specification.6 Annex A (normative): Protocol ICS proforma for TS 102 115-2.7 A.1 Guidance for complet

9、ing the proforma 7 A.1.1 Purposes and structure7 A.1.2 Abbreviations and conventions 7 A.1.3 Instructions for completing the PICS proforma9 A.2 Identification of the implementation 9 A.2.1 Date of the statement9 A.2.2 Implementation Under Test (IUT) identification .9 A.2.3 System Under Test (SUT) id

10、entification9 A.2.4 Product supplier10 A.2.5 Client 10 A.2.6 PICS contact person .11 A.3 Identification of the protocol11 A.4 Global statement of conformance.11 A.5 Roles.12 A.6 PICS for Access Terminal (AT) or Access Point (AP) 12 A.6.1 Service Specific Convergence Sublayer (SSCS) procedures12 A.6.

11、2 SSCS_PDU description12 A.6.3 SSCS PDU parameters .13 History 14 ETSI ETSI TS 102 147-2-1 V1.2.1 (2004-04) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is pu

12、blicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ET

13、SI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are

14、, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Broadband Radio Access Networks (BRAN). The present document is part 2, sub-part 1 of a multi-part covering Broadband Radio Access Networks (BRAN); HIPERACCESS;

15、 Cell based Convergence Layer, as identified below: Part 1: “Common part“; Part 2: “UNI Service Specific Convergence Sublayer (SSCS)“; Sub-part 1: “Protocol Implementation Conformance Statement (PICS) proforma“; Sub-part 2: “Test Suite Structure and Test Purposes (TSS Sub-part 3: “Abstract Test Suit

16、e (ATS)“. Introduction To evaluate conformance of a particular implementation, it is necessary to have a statement of which capabilities and options have been implemented for a telecommunication specification. When such a statement is based on a protocol, it is called PICS. ETSI ETSI TS 102 147-2-1

17、V1.2.1 (2004-04) 5 1 Scope The present document provides the PICS proforma for TS 102 115-2 1 in compliance with the relevant requirements, and in accordance with the relevant guidance given in ISO/IEC 9646-7 4 and ETS 300 406 2. It details in tabular form the implementation options, i.e. the option

18、al functions additional to those, which are mandatory to implement. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or

19、 version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ETS

20、I TS 102 115-2: “Broadband Radio Access Networks (BRAN); HIPERACCESS; Cell based Convergence Layer; Part 2: UNI Service Specific Convergence Sublayer (SSCS)“. 2 ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization me

21、thodology“. 3 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 4 ISO/IEC 9646-7: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Impleme

22、ntation conformance statement“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ISO/IEC 9646-1 3, ISO/IEC 9646-7 4 TS 102 115-2 1 and the following apply: ICS proforma: document, in the form of a questionnaire, which when c

23、ompleted for an implementation or system becomes an ICS Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system claimed to conform to a given specification, stating which capabilities have been implemented. The ICS can take several forms: protocol IC

24、S, profile ICS, profile specific ICS, information object ICS, etc. Protocol ICS (PICS): ICS for an implementation or system claimed to conform to a given protocol specification ETSI ETSI TS 102 147-2-1 V1.2.1 (2004-04) 6 3.2 Abbreviations For the purposes of the present document, the following abbre

25、viations apply: AP Access Point AT Access Terminal ATM Asynchronous Transfer Mode BRAN Broadband Radio Access Networks (Project) DLC Data Link Control DUC DLC User Connection SAP Service Access Point SSCS Service Specific Convergence Sublayer UNI User Network Interface IUT Implementation Under Test

26、SUT System Under Test 4 Conformance to this PICS proforma specification If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be technically equivalent to the text of the PICS proforma given in annex A, and shall preserve the numbering/naming a

27、nd ordering of the proforma items. A PICS, which conforms to the present document, shall be a conforming PICS proforma completed in accordance with the guidance for completion given in clause A.1. ETSI ETSI TS 102 147-2-1 V1.2.1 (2004-04) 7 Annex A (normative): Protocol ICS proforma for TS 102 115-2

28、 Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the PICS proforma in this annex so that it can be used for its intended purposes and may further publish the completed PICS. A.1 Gu

29、idance for completing the proforma A.1.1 Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the requirements defined in TS 102 115-2 may provide information about the implementation in a standardized manner. The PICS proforma

30、 is subdivided into subclauses for the following categories of information: - Guidance for completing the PICS proforma; - Identification of the implementation; - Identification of the protocol; - Global statement of conformance; - Roles; - Major capabilities; - PDUs and PDU parameters. A.1.2 Abbrev

31、iations and conventions The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7. Item column The item column contains a number, which identifies the item in the table. Item description column The item descrip

32、tion column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“. Status column The following notations, defined in ISO/IEC 9646-7, are used for the status column: m mandatory - the capability is required to be support

33、ed. o optional - the capability may be supported or not. n/a not applicable - in the given context, it is impossible to use the capability. x prohibited (excluded) - there is a requirement not to use this capability in the given context. o.i qualified optional - for mutually exclusive or selectable

34、options from a set. “i“ is an integer which identifies an unique group of related optional items and the logic of their selection which is defined immediately following the table. ETSI ETSI TS 102 147-2-1 V1.2.1 (2004-04) 8 ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“)

35、depends on the support of other optional or conditional items. “i“ is an integer identifying an unique conditional status expression which is defined immediately following the table. i irrelevant (out-of-scope) - capability outside the scope of the reference specification. No answer is requested fro

36、m the supplier. NOTE 1: This use of “i“ status is not to be confused with the suffix “i“ to the “o“ and “c“ statuses above. Reference column The reference column makes reference to TS 102 115-2, except where explicitly stated otherwise. Support column The support column shall be filled in by the sup

37、plier of the implementation. The following common notations, defined in ISO/IEC 9646-7, are used for the support column: Y or y supported by the implementation. N or n not supported by the implementation. N/A, n/a or - no answer required (allowed only if the status is n/a, directly or after evaluati

38、on of a conditional status). If this PICS proforma is completed in order to describe a multiple-profile support in a system, it is necessary to be able to answer that a capability is supported for one profile and not supported for another. In that case, the supplier shall enter the unique reference

39、to a conditional expression, preceded by “?“ (e.g. ?3). This expression shall be given in the space for comments provided at the bottom of the table. It uses predicates defined in the SCS, each of which refers to a single profile and which takes the value TRUE if and only if that profile is to be us

40、ed. EXAMPLE 1: ?3: IF prof1 THEN Y ELSE N NOTE 2: As stated in ISO/IEC 9646-7, support for a received PDU requires the ability to parse all valid parameters of that PDU. Supporting a PDU while having no ability to parse a valid parameter is non-conformant. Support for a parameter on a PDU means that

41、 the semantics of that parameter are supported. Values allowed column The values allowed column contains the type, the list, the range, or the length of values allowed. The following notations are used: - range of values: example: 5 20 - list of values: , , ., example: 2 ,4 ,6 ,8, 9 example: 1101B,

42、1011B, 1111B example: 0AH, 34H, 2FH - list of named values: (), (), ., () example: reject(1), accept(2) - length: size ( ) example: size (1 8) Values supported column The values supported column shall be filled in by the supplier of the implementation. In this column, the values or the ranges of val

43、ues supported by the implementation shall be indicated. ETSI ETSI TS 102 147-2-1 V1.2.1 (2004-04) 9 References to items For each possible item answer (answer in the support column) within the PICS proforma a unique reference exists, used, for example, in the conditional expressions. It is defined as

44、 the table identifier, followed by a solidus character “/“, followed by the item number in the table. If there is more than one support column in a table, the columns are discriminated by letters (a, b, etc.), respectively. EXAMPLE 2: A.5/4 is the reference to the answer of item 4 in table 5 of anne

45、x A. EXAMPLE 3: A.6/3b is the reference to the second answer (i.e. in the second support column) of item 3 in table 6 of annex A. Prerequisite line A prerequisite line takes the form: Prerequisite: . A prerequisite line after a clause or before a table title indicates that the whole clause or the wh

46、ole table is not required to be completed if the predicate is FALSE. A.1.3 Instructions for completing the PICS proforma The supplier of the implementation shall complete the PICS proforma in each of the spaces provided. In particular, an explicit answer shall be entered, in each of the support or s

47、upported column boxes provided, using the notation described in clause A.1.2. If necessary, the supplier may provide additional comments in space at the bottom of the tables or separately. More detailed instructions are given at the beginning of the different subclauses of the PICS proforma. A.2 Ide

48、ntification of the implementation Identification of the Implementation Under Test (IUT) and the system in which it resides (the System Under Test (SUT) should be filled in so as to provide as much detail as possible regarding version numbers and configuration options. A.2.1 Date of the statement Tab

49、le A.1: Date of statement Date of statement Day Month Year A.2.2 Implementation Under Test (IUT) identification The supplier of the implementation shall enter information necessary to uniquely identify the IUT in table A.2. Table A.2: IUT identification IUT identification IUT name IUT version A.2.3 System Under Test (SUT) identification The supplier of the implementation shall enter information necessary to uniquely identify the SUT in table A.3. ETSI ETSI TS 102 147-2-1 V1.2.1 (2004-04) 10Table A.3: SUT identification SUT identification