ETSI GSM 04 84-1994 European Digital Cellular Telecommunications System (Phase 2) Multi Party (MPTY) Supplementary Services - Stage 3《欧洲数字蜂窝通信系统(第2阶段) 多方通话(MPTY)补充业务 第3阶段》.pdf

《ETSI GSM 04 84-1994 European Digital Cellular Telecommunications System (Phase 2) Multi Party (MPTY) Supplementary Services - Stage 3《欧洲数字蜂窝通信系统(第2阶段) 多方通话(MPTY)补充业务 第3阶段》.pdf》由会员分享，可在线阅读，更多相关《ETSI GSM 04 84-1994 European Digital Cellular Telecommunications System (Phase 2) Multi Party (MPTY) Supplementary Services - Stage 3《欧洲数字蜂窝通信系统(第2阶段) 多方通话(MPTY)补充业务 第3阶段》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、m 3404583 OLO5400 714 m . Released: 15 February 1994 GSM 04.84 Version: 4.3.0 Date: 21 January 1994 Source: ETSI TC-SMG Reference: GSM 04.84 UDC: 621.396.21 Key words: European digital cellular telecommunications system, Global System for Mobile communications (GSM) European digital cellular telecom

2、munications system (Phase 2); Multi Party (MPTY) supplementary services - Stage 3 (GSM 04.84) ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: 06921 Sophia Antipolis Cedex - FRANCE Office address: Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE Tel.: +

3、33 92 94 42 O0 - Fax: + 33 93 65 47 16 0 European Telecommunications Standards Institute 1 994. All rights reserved. No part may be reproduced except as authorised by written permission. The copyright and the foregoing restriction on reproduction extend to all media in which the information may be e

4、mbodied. Page z GSM 04.84 version 4.3.0 = 3404583 OI10540L b50 = . Whilst every care has been taken in the preparation and publication of this document, errors in content, typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to “ETSI Editing and Standards

5、 Approval Dept.“ at the address shown on the title page. Page 3 GSM 04.84 version 4.3.0 3404583 0305402 597 Contents Foreword . 5 O General . 7 o . 1 Scope . 7 0.2 Normative references 7 0.3 Definitions and abbreviations . 9 1 Multi Patty service (MPTY) . 10 1.1 1.2 Managing an active multi party ca

6、ll . 11 1.2.1 Served mobile subscriber 11 1.2.1.1 Put the multi party call on hold . 11 1.2.1.2 Create a private communication with one of the 1.2.1.3 Terminate the entire multi party call 12 1.2.1.4 Explicitly disconnect a remote party 12 1.2.2 Remote Parties 12 1.2.2.1 Release from the multi party

7、 call . 12 1.2.2.2 Place his connection to the multi party call on hold. Beginning the multi party service 10 remote parties . 12 and typically later retrieve it., . 12 1.3 Managing a held multi party call . 13 1.3.1 Served mobile subscriber 13 1.3.1.1 Retrieve the held multi party call . 13 1.3.1.2

8、 initiate a new call . 13 1.3.1.3 Process a call waiting request 13 1.3.1.4 Terminate the held multi party call 13 1.3.1.5 Explicitly disconnect a remote party 13 1.3.2 Remote parties 14 Managing a single call and a multi party call . 14 1.4.1 Served mobile subscriber 14 1.4.1.1 Disconnect the singl

9、e call 14 1.4.1.2 Disconnect the MPTY . 14 1.4.1.3 Disconnect all calls . 14 1.4.1.4 Add the single call to the MPTY . 14 1.4.1.5 Alternate between the MPTY call and the single call 14 1.4 1.5 1.6 1 . 7 1.8 Adding extra remote parties . 15 Auxiliary states for MPTY 15 Activation. deactivation. regis

10、tration. erasure and interrogation . 15 Simultaneous use of multi party operations 15 History 16 m 3404583 0105403 y23 m Page 5 GSM 04.84 version 4.3.0 Foreword The section will be provided later. Previous page is blank Page 7 GSM 04.84 version 4.3.0 9 3404583 0305404 3bT 9 O General o. 1 Scope This

11、 technical specification specifies the procedures used at the radio interface (Reference point Um as defined in technical specification GSM 04.02) for normal operation and invocation of multi party supplementary services. In technical specification GSM 04.1 O the general aspects of the specification

12、 of supplementary services at the layer 3 radio interface are given. Technical specification GSM 04.80 specifies the formats and coding for the supplementary services. Definitions and descriptions of supplementary services are given in technical specification GSM 02.04 and the GSM 02.8 and 02.9-seri

13、es. Technical specification GSM 02.84 is related specially to multi party supplementary services. Technical realization of supplementary services is described in technical specification GSM 03.1 1 and the GSM 03.8 and 03.9-series. Technical specification GSM 03.84 is related specially to multi party

14、 supplementary services. The procedures for Call Control, Mobility Management and Radio Resource management at the layer 3 radio interface are defined in technical specifications GSM 04.07 and GSM 04.08. The following supplementary service belongs to the multi party supplementary services and is des

15、cribed in this technical specification: - Multi patty service (MPTY) (section 1) 0.2 Normative references This ETS incorporates by dated and undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are list

16、ed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this ETS only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. t11 21 i31 i41 51 i61 GSM 01.04: “Europea

17、n digital cellular telecommunications system (Phase 2); “Abbreviations and acronyms“. GSM 02.04: “European digital cellular telecommunications system (Phase 2); General on supplementary services“. GSM 02.81 : “European digital cellular telecommunications system (Phase 2); Line identification supplem

18、entary services - Stage 1 “. GSM 02.82: “European digital cellular telecommunications system (Phase 2); Call Forwarding (CF) supplementary services - Stage 1 “. GSM 02.83: “ European digital cellular telecommunications system (Phase 2); Call Waiting (CW) and Call Hold (HOLD) supplementary services -

19、 Stage 1 n. GSM 02.84: “European digital cellular telecornmunications system (Phase 2); Multi Patty (MPTY) supplementary services - Stage 1 n. Previous page is blank Page 8 GSM 04.84 version 4.3.0 = 3404563 0305405 2Tb i71 i81 191 lo1 i111 i121 131 i141 i1 51 i161 il 71 il 81 i1 91 i201 121 1 i221 i

20、231 i241 GSM 02.85: “European digital cellular telecommunications system (Phase 2); Closed User Group (CUG) supplementary services - Stage 1 “. GSM 02.86: “ European digital cellular telecommunications system (Phase 2); Advice of charge (AOC) supplementary services - Stage 1 “. GSM 02.88: “European

21、digital cellular telecommunications system (Phase 2); Call Barring (CB) supplementary services - Stage 1 “. GSM 02.90: “European digital cellular telecommunications system (Phase 2); Unstructured supplementary services operation - Stage 1 “. GSM 03.1 1 : “European digital cellular telecommunications

22、 system (Phase 2); Technical realization of supplementary services“. GSM 03.81 : “European digital cellular telecommunications system (Phase 2); Line identification supplementary services - Stage 2“. GSM 03.82: “European digital cellular telecommunications system (Phase 2); Call Forwarding (CF) supp

23、lementary services - Stage 2“. GSM 03.83: “European digital cellular telecommunications system (Phase 21; Call Waiting (CW) and Call Hold (HOLD) supplementary services - Stage 2“. GSM 03.84: “European digital cellular telecommunications system (Phase 2); Multi Party (MPTY) supplementary services - S

24、tage 2“. GSM 03.85: “European digital cellular telecommunications system (Phase 2); Closed User Group (CUG) supplementary services - Stage 2“. GSM 03.86: European digital cellular telecommunications system (Phase 2); Advice of Charge (AOC) supplementary services - Stage 2“. GSM 03.88: “ European dig

25、ital cellular telecommunications system (Phase 2); Call Barring (CB) supplementary services - Stage 2“. GSM 03.90: “ European digital cellular telecommunications system (Phase 2); Unstructured supplementary services operation - Stage 2“. GSM 04.02: “European digital cellular telecommunications syste

26、m (Phase 2); GSM Public Land Mobile Network (PLMN) access reference configuration“. GSM 04.07: “European digital cellular telecommunications system (Phase 2); Mobile radio interface signalling layer 3 General aspects“ GSM 04.08: “European digital cellular telecommunications (Phase 2); Mobile radio i

27、nterface layer 3 specification“. GSM 04.1 O: “ European digital cellular telecommunications (Phase 2); Mobile radio interface layer 3 Supplementary specification General aspects“. GSM 04.80: European digital cellular telecommunications (Phase 2); Mobile radio interface layer 3 supplementary specific

28、ation Formats and coding“. system system services system services i251 rn 3404583 OiI0540b 132 rn Page 9 GSM 04.84 version 4.3.0 GSM 04.83: “European digital cellular telecommunications system (Phase 2); Call Waiting (CW) and Call Hold (HOLD) supplementary services - Stage 3“. 0.3 Definitions and ab

29、breviations Abbreviations used in this specification are listed in TS GSM 01.04. Page IV GSM 04.84 version 4.3.0 1 Multi Party service (MPTY) 3404583 Ol10.5407 077 1.1 Beginning the multi party service The served mobile subscriber A may initiate an active multi party call from an active call C and a

30、 held call B. The mobile station invokes the service by sending a FACILITY message to the network containing the BuildMPTY request. This BuildMPTY request indicates to the network that the mobile subscriber wishes all his calls to be connected together in a multi party call. The network will normall

31、y accept the request and connect the mobile subscriber with the other existing connections (active call C and held call B). If the request is not accepted, the network will indicate the error to the served mobile, see figure 1.1. The network confirms with the same transaction identifier. Error value

32、s are specified in TS GSM 04.80. During the BuildMPTY operation the MS shall run a timer T(Bui1dMPTY). This timer is started when the operation is sent, and stopped when a response is received from the network. If this timer expires the MS shall assume that the operation has failed, locally release

33、the invokelD, and may re- attempt the operation or inform the user of the failure. MS Network FACILITY (TI A-B/A-C) Facility (Invoke = BuildMPTY) FACILITY/DISCONNECT/RELEASE/RELEASE COMPLETE (TI A-B/A-C) _-*- Facility (Invoke = RetrieveMPTY) FACILITY/DISCONNECT/RELEASE/RELEASE COMPLETE (TI A-X) -*-*

34、-. Facility (Return error (Error) FACILITY/DISCONNECT/RELEASE/RELEASE COMPLETE (TI A-X) -*- Facility (Reject (Invoke-problem) NOTE: X = Any remote party in multi party call. Figure 1.6: Served mobile subscriber retrieves multi party call Indications are sent towards all remote parties by means of no

35、rmal CallOnHold ( = CallRetrieved) notifications as described in TS GSM 04.83. 1.3.1.2 Initiate a new call This is achieved by normal call set-up procedures (TS GSM 04-08). 1.3.1.3 Process a call waiting request This is described in TS GSM 04.83. 1.3.1.4 Terminate the held multi party call This is a

36、chieved by the same procedure as in section 1.2.1.3. 1.3.1.5 Explicitly disconnect a remote party This is achieved by the same procedure as in section 1.2.1 -4. Pabe I7 GSM 04.84 version 4.3.0 rn 3404583 0105411 5TT rn 1.3.2 Remote parties During a held multi party call any remote party is able to p

37、erform the same operations as described for an active multi party call in section 1.2.2. 1.4 Managing a single call and a multi party call 1.4.1 Served mobile subscriber If the served mobile subscriber is connected to a multi party call (active or on hold) and another single call (active or on hold)

38、, he can request the network to: 1.4.1.1 Disconnect the single call This is achieved by using the call clearing procedure as described in TS GSM 04.08 with the transaction identifier corresponding to the single call. 1.4.1.2 Disconnect the MPTY This is achieved by the same procedure as disconnecting

39、 a held/active MPTY without another call, see section 1.2.1 and 1.3.1. 1.4.1.3 Disconnect all calls This is achieved by using the procedures in sections 1.4.1 .I and 1.4.1.2. 1.4.1.4 Add the single call to the MPTY The served mobile subscriber may request the connection of all his calls, held and ac

40、tive, into an active multi party call at any time by sending a FACILITY message with the transaction identifier corresponding to any remote party and containing the BuildMPTY invoke component, see section 1 .I. This procedure will apply whether the multi party call is on hold or active, and whether

41、the single call is on hold or active. If the request is successful, previously held remote parties will receive an MPTY notification and a CallRetrieved notification as shown in figure 1.2, and previously active remote parties will receive an MPTY notification as shown in figure 1.3. If the network

42、did not receive a non-zero SS Screening indicator from the remote partys mobile station it shall not send a notification. If the request is unsuccessful e.g. because the maximum number of remote parties has already been reached, then an error is returned to the served mobile subscriber, as shown in

43、figure 1 .I. Error values are specified in TS GSM 04.80. 1.4.1.5 Alternate between the MPTY call and the single call This procedure follows the Alternate procedure defined in TS GSM 04.83 with the exception that the MPTY call is heldhetrieved using HoldMPTY/RetrieveMPTY in place of HOLD/RETRIEVE as

44、follows: Sinole call MPTY call (Facility) HOLD Invoke (HoldMPTY) HOLD ACKNOWLEDGE Return result HOLD REJECT Return error (error) RETRIEVE Invoke (RetrieveMPTY) RETRIEVE ACKNOWLEDGE Return result RETRIEVE REJECT Return error (error) Page 15 GSM 04.84 version 4.3.0 m 3404583 0105412 436 m 4 1.5 Adding

45、 extra remote parties Extra remote parties are added by placing the multi party call on hold (section 1.2.1.1 1, setting up a new connection (either a new call or a waiting call) and then sending a FACILITY message to the network requesting that the active call be joined with the MPTY, using the sam

46、e signalling as for invocation, see figure 1.1. This results in an active multi party call. Notifications are sent as for the initial invocation (.e. previously-held parties in MPTY receive CallRetrieved notifications and MPTY notifications; the new remote party only receives an MPTY notification),

47、see figures 1.2 and 1.3. If the network did not receive a non-zero SS Screening indicator from the remote partys mobile station it shall not send a notification. If the request is not accepted, e.g. because the maximum number of remote parties has already been reached, then the error is indicated to

48、 the mobile station. Error values are specified in TS GSM 04.80. 1.6 Auxiliary states for MPTY In the call hold service (TS GSM 04.831, a two dimensional state space is defined, where the first dimension corresponds to the GSM 04.08 call control state and the second dimension corresponds to the call

49、 hold state (Idle, Hold Request, Call Held, Retrieve Request). For the purposes of the MPTY service, it is necessary to introduce another dimension to this state space, .e. the multi party state. There are four auxiliary states associated with the MPTY service: Idle; MPTY request; A request has been made to add this call to the MPTY. Call in MPTY; This call is in the MPTY Split request; A reque