ETSI ETS 300 705-2-1997 Digital Enhanced Cordless Telecommunications (DECT) Integrated Services Digital Network (ISDN) DECT ISDN Interworking for End System Configuration Profile I.pdf

《ETSI ETS 300 705-2-1997 Digital Enhanced Cordless Telecommunications (DECT) Integrated Services Digital Network (ISDN) DECT ISDN Interworking for End System Configuration Profile I.pdf》由会员分享，可在线阅读，更多相关《ETSI ETS 300 705-2-1997 Digital Enhanced Cordless Telecommunications (DECT) Integrated Services Digital Network (ISDN) DECT ISDN Interworking for End System Configuration Profile I.pdf（68页珍藏版）》请在麦多课文档分享上搜索。

1、ETS 300 705-2 June 1997 Source: ETSI EP-DECT Reference: DEECT-040045-2 ICs: 33.020 Key words: DECT, ISDN, ICs, radio, testing Digital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital Network (ISDN); DECTASDN interworking for end system configuration; Profile Implementation Co

2、nformance Statement (ICs); Part 2: Fixed radio Termination (FT) ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6921 Sophia Antipolis CEDEX - FRANCE mice address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE X.400: c=fr, a=atlas, p=etsi, s-ec

3、retariat - Internet: secretariatQetsi.fr Tel.: 43 4 92 94 42 O0 - Fax: 43 4 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standar

4、ds Institute 1997. All rights reserved. STD-ETSI ETS 300 705-2-ENGL 1797 W 3400855 0207b33 77T II Page 2 ETS 300 705-2: June 1997 Whilst every care has been taken in the preparation and publication of this document, errors in content, typographical or otherwise, may occur. If you have comments conce

5、rning its accuracy, please write to “ETSI Editing and Committee Support Dept.“ at the address shown on the title page. STD-ETSI ETS 300 705-2-ENGL 1917 3LiO0855 0207b34 8Ob = Page 3 ETS 300 705-2: June 1997 Contents Foreword . 7 1 Scope . 9 2 Normative references . 9 3 Definitions and abbreviations

6、11 3.1 Definitions . 11 3.2 Abbreviations 11 4 Conformance requirement concerning Profile ICs . 11 Annex A (normative): System Conformance Statement (SCS) proforma for DECT FT IAP 14 A.l Identification 14 A.l.l Description of the system . 14 A.1.2 Supplier of the system . 14 A.1.3 Client identificat

7、ion -15 A.1.4 Contact person identification . 15 A.1.5 Signature of the client or of the supplier . 15 A.2 Protocol identification . 16 A.3 Profile identification 16 A.4 Combination description table -16 AS Configurability table . 16 A.6 Additional information . 17 Annex B (normative): Requirement l

8、ists for DECT FT IAP 18 B.l General 18 B.1.1 Profile Requirement List (Profile RL) . 18 B.1.2 General conditions . 19 B.2 Requirement lists on DECT protocols 19 8.2.1 Requirement list on DECT NWK layer . 19 B.2.1.1 Network entities 19 B.2.1 . 2 Network features 19 B.2.1.2.1 CC features 19 8.2.1.2.2

9、SS features (services) . 20 8.2.1.2.3 LCE features 22 B.2.1.3 Procedures 22 B.2.1.4 Messages 24 B.2.1.4.1 CC messages . 24 8.2.1.4.3 LCE messages . 25 B.2.2.1.1 C-plane services . 26 B.2.1.4.2 CRSS and CISS messages . 25 Requirement list on DECT DLC layer 26 8.2.2.1 Services . 26 8.2.2 B.2.2.1.2 U-p

10、lane services . 26 8.2.2.2 Procedures 26 STD-ETSI ETS 300 705-2-ENGL 1797 1qnn855 0207b35 7q2 Page 4 ETS 300 705-2: June 1997 B.2.2.2.1 8.2.2.2.2 Generic signalling procedures 26 Class A procedures . 27 8.2.2.2.3 Broadcast procedures . 27 B.2.2.2.4 LU1 procedures 27 8.2.2.3.1 LU1 parameters 27 B.2.2

11、.4 Messages 28 8.2.2.4.1 C-plane PDUs . 28 Requirement list on DECT MAC layer 28 B.2.2.3 Parameters 27 8.2.3 8.2.3.1 8.2.3.2 8.2.3.3 B.2.3.4 B.2.3.5 Services . 28 8.2.3.1.1 8.2.3.1.2 Procedures 31 8.2.3.2.1 8.2.3.2.2 8.2.3.2.3 B.2.3.2.5 8.2.3.2.6 Messages 33 8.2.3.4.1 B.2.3.4.2 8.2.3.4.3 Connection

12、oriented control services . 28 Broadcast control services . 29 B.2.3.1.3 Multiplexing services 29 Connection setup procedures . 31 Connection data transfer procedures 31 Connection release procedures 31 8.2.3.2.4 Broadcast procedures . 31 CSF multiplexing procedures 32 Layer management procedures 32

13、 Other capabilities 32 A-field header - B-field identification 33 Paging tail messages supported . 33 MAC control messages supported . -34 8.2.3.4.4 8.2.3.5.1 B-field messages supported . 34 QT - Fixed part capability 36 Requirement list on DECT PHL layer . 36 Requirement list on ISDN L3 layer table

14、s . 37 B.2.5.1 ISDN L3 layer primary access tables 37 8.2.5.2 ISDN L3 layer basic access tables . 37 Requirement list on ISDN L2 layer tables . 37 B.2.6.1 ISDN L2 layer primary access tables 37 B.2.6.2 ISDN L2 layer basic access tables . 37 Requirement list on ISDN L1 layer tables . 37 B.2.7.1 ISDN

15、L1 layer primary access tables 37 8.2.7.2 ISDN L1 layer basic access tables . 37 MAC messages format and field value 36 8.2.4 B.2.5 8.2.6 8.2.7 Annex C (normative): Profile specific ICs proforma for DECT FT IAP 38 C.l Guidance for completing the profile specific proforma . 38 C.l.l C.l . 2 Instructi

16、ons for completing the Profile specific ICs . 40 Purposes and structure 38 C.2 Identification of the implementation 40 C.2.1 Date of statement 40 C.2.2 Identification of the implementation 40 C.2.3 Contact person identification . 40 C.2.4 Relationship with the System Conformance Statement (SCS) 41 C

17、.3 Identification of the profile . 41 C.3.1 C.3.2 Addenda implemented 42 Defect report numbers and amendments implemented 41 C.4 Profile ICs proforma tables 42 C.4.1 Global statement of conformance . 42 (2.4.2 Profile ICs features tables . 42 C.4.3 Profile ICs IWU tables . 43 C.4.3.1 IWU procedures

18、. 43 STD*ETSI ETS 300 705-2-ENGL 1997 8 3400855 0207b3b b89 W Page 5 ETS 300 705-2: June 1997 C.4.3.2 IWU messages mapping . 45 Profile ICs NWK layer tables 53 Profile ICs DLC layer tables . 53 Profile ICs MAC layer tables 53 C.4.4 C.4.5 C.4.6 Annex D (normative): Messages redefinition for DECT CI F

19、T PICS proforma . 54 D.l Description 54 D.2 CC messages . 54 D.3 Connection Related Supplementary Service (CRSS) and Connection Independent Supplementary Service (CISS) messages 62 D.4 Information elements 66 D.5 Timers and constants support . 69 History . 70 STD-ETSI ETS 300 705-2-ENGL 1777 3900855

20、 0207b37 515 Page 7 ETS 300 705-2: June 1997 Foreword This European Telecommunication Standard (ETS) has been produced by the Digital Enhanced Cordless Telecommunications (DECT) Project of the European Telecommunications Standards Institute (ETSI). This ETS comprises two parts: Pari 1 : “Portable ra

21、dio Termination (PT)“. Part 2: “Fixed radio Termination (Fr)“. Annex A of this ETS contains the System Conformance Statement (SCS) proforma for the DECT FT ISDN Access Profile (IAP). Annex B of this ETS contains the requirement lists for the DECT FT IAP Annex C of this ETS contains the specific ICs

22、proforma for the DECT FT IAP. Transposition dates Date of adoption: 6 June 1997 1 Date of latest announcement of this ETS (doa): 30 September 1997 I Date of latest publication of new National Standard or endorsement of this ETS (dop/e): 31 March 1998 1 Date of withdrawal of any conflicting National

23、Standard (dow): 31 March 1998 Previous page is blank STD-ETSI ETS 300 705-2-ENLL 1777 m 31i00855 0207b38 q5L m Page 9 ETS 300 705-2: June 1997 1 scope This European Telecommunication Standard (ETS) provides the Profile Implementation Conformance Statement (Profile ICs) proforma for the Digital Enhan

24、ced Cordless Telecommunications DECTASDN inter- working for end system configuration Profile at the Fixed Termination as defined in ETS 300 434-1 lo, and ETS 300 434-2 ll in compliance with the relevant requirements and in accordance with the relevant guidance given in ISOAEC 9646-7 18. The supplier

25、 of an implementation which is claimed to conform to ETS 300 434-1 lo and ETS 300 434-2 l 11 is required to complete a copy of the PICS proforma ETS 300 476 parts 4, 5, 6 and 7 12, 13, 14 and 15, with the replacements provided by the requirement lists given in annex B of this ETS, as well as a copy

26、of the specific ICs proforma provided in the annex C of this ETS. 2 Normative references This ETS incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For

27、 dated references, subsequent amendments to or revisions of any of these publications apply to this ETS only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. 31 41 I51 71 91 ETS 300 175-1 : “Digital Enhanced Cordless

28、Telecommunications (DECT); Common Interface (Ci); Part 1 : Overview“. ETS 300 175-2: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (Ci); Part 2: Physical layer (PHL)“. ETS 300 175-3: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (Ci); Part 3: Medium

29、Access Control (MAC) layer“. ETS 300 175-4: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (Ci); Part 4: Data Link Control (DLC) layer“. ETS 300 175-5: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (Ci); Part 5: Network (NWK) layer“. ETS 300 175-6: “D

30、igital Enhanced Cordless Telecommunications (DECT); Common Interface (Ci); Part 6: Identities and addressing“. ETS 300 175-7: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (Ci); Part 7: Security features“. ETS 300 175-8: “Digital Enhanced Cordless Telecommunications (DECT);

31、Common Interface (Ci); Part 8: Speech coding and transmission“. ETS 300 175-9: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (Ci); Part 9: Public Access Profile (PAP)“. ETS 300 434-1 : “Digital Enhanced Cordless Telecommunications (DECT) and Integrated Services Digital Netwo

32、rk (ISDN) interworking for end system configuration; Part 1 : Interworking specification“. ETS 300 434-2: “Digital Enhanced Cordless Telecommunications (DECT) and Integrated Services Digital Network (ISDN) interworking for end system configuration; Part 2: Access profile“. ETS 300 476-4: “Digital En

33、hanced Cordless Telecommunications (DECT); Common Interface (Ci); Protocol Implementation Conformance Statement (PICS) proforma; Part 4: Network (NWK) layer - Fixed radio Termination (FT)“. Previous page is blank STD-ETSI ETS 300 705-2-ENGL 1777 M 300855 0207b37 378 m Page 10 ETS 300 705-2: June 199

34、7 I 41 i 51 ETS 300 476-5: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (Ci); Protocol Implementation Conformance Statement (PICS) proforma; Part 5: Data Link Control (DLC) layer - Fixed radio Termination (FT)“. ETS 300 476-6: “Digital Enhanced Cordless Telecommunications (

35、DECT); Common Interface (Ci); Protocol Implementation Conformance Statement (PICS) proforma; Part 6: Medium Access Control (MAC) layer - Fixed radio Termination (FT)“. ETS 300 476-7: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (Ci); Protocol Implementation Conformance Stat

36、ement (PICS) proforma; Part 7: Physical layer“. ISO/IEC 9646-1 (1 991): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1 : General concepts“. (See also CCITT Recommendation X.290 (1 991). ISO/IEC 9646-6 (1 991): “Information technology -

37、 Open Systems Interconnection - Conformance testing methodology and framework - Part 6: Protocol profile test specification“. ISO/IEC 9646-7 (1 991): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation conformance statement“

38、. ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. ETS 300 403-1 : “Integrated Services Digital Network (ISDN): Digital Subscriber Signalling System No. one (DSSl) protocol; Signalling network layer for

39、circuit-mode basic call control; Part 1 : Protocol specification ITU-T Recommendation Q.931 (1 993), modified“. ETS 300 403-3: “Integrated Services Digital Network (ISDN); Digital Subscriber Signalling System No. one (DSSI) protocol; Signalling network layer for circuit-mode basic call control; Part

40、 3: Protocol Implementation Conformance Statement (PICS) proforma specification“. ETS 300 402-2: “Integrated Services Digital Network (ISDN); Digital Subscriber Signalling System No. one (DSS1) protocol; Data link layer; Part 2: General protocol specification ITU-T Recommendation Q.921 (1 993), modi

41、fied“. ETS 300 402-4: “Integrated Services Digital Network (ISDN); Digital Subscriber Signalling System No. one (DSSl) protocol: Data link layer; Part 4: Protocol Implementation Conformance Statement (PICS) proforma specification for the general protocol“. ETS 300 O1 1 (1 992): “Integrated Services

42、Digital Network (ISDN); Primary rate user-network interface; Layer 1 specification and test principles“. ETS 300 O1 l/A: “Amendment 2 to ETS 300 O11 (1992), adding a SCS, a PICS and a PIXIT for interface points I a and ib“. ETS 300 012 (1 992): “Integrated Services Digital Network (ISDN); Basic user

43、- network interface; Layer 1 specification and test principles“. ETS 300 O1 2/A2: “Amendment 2 to ETS 300 O1 2 (1 992), adding a SCS, a PICS and a PIXIT for interface points I a and ib“. STD-ETSI ETS 300 705-2-ENGL 1797 3YOOA55 0207bq0 OUT H Page 11 ETS 300 705-2: June 1997 ETS 300 196-1 : “Integrat

44、ed Services Digital Network (ISDN); Generic functional protocol for the support of supplementary services; Digital Subscriber Signa Iling System No. one (DSS1) protocol; Part 1 : Protocol specification“. ETS 300 196-2: “Integrated Services Digital Network (ISDN); Generic functional protocol for the

45、support of supplementary services: Digital Subscriber Signa Iling System No. one (DSS1) protocol; Part 2: Protocol Implementation Conformance Statement (PICS) proforma specification“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of this ETS, the following terms and definitions ap

46、ply: a) the terms defined in ISO/IEC 9646-7 18; b) the definitions in ETS 300 434-1 lo and ETS 300 434-2 ll; and c) the following terms defined in ISO/IEC 9646-1 16: - PICS proforma: - Profile implementation Conformance Statement (Profile ICs). 3.2 Abbreviations For the purposes of this ETS, the abb

47、reviations defined in IS OAEC 9646-1 16, the abbreviations defined in ETS 300 434-1 lo and ETS 300 434-2 ll apply. 4 Conformance requirement concerning Profile ICs The supplier of a protocol implementation which is claimed to conform to the Fixed Termination specific requirements of ETS 300 434-1 lo

48、 and ETS 300 434-2 ll shall: - verify that his protocol implementation meets the Profile Requirements Lists (Profile RLs) for each DECT protocol layer, contained in annex Bof this ETS; - complete a copy of the Profile specific ICs proforma provided in annex C; - complete a copy of the System Conform

49、ance Statement (SCS) proforma provided in annex A; and - provide the information necessary to identify both the supplier and the implementation. Tables 1 and 2 provide guidance to indicate how to fulfil the PICS proforma required for the profile. STD-ETSI ETS 300 705-2-ENGL 1997 3400855 0207b4l T4b Page 12 ETS 300 705-2: June 1997 Table 1 : DECT PICS proforma table Tables Change A.12 A.13 to A.16 Status column updated by RL subclause B.2.1.1 Status column updated by RL subclause B.2.1.2 A.18 to A.20 A.23 to A.24 IStatus column updated