ETSI EN 300 487-2016 Satellite Earth Stations and Systems (SES) Harmonised Standard for Receive-Only Mobile Earth Stations (ROMES) providing data communications operating in the 1 .pdf

《ETSI EN 300 487-2016 Satellite Earth Stations and Systems (SES) Harmonised Standard for Receive-Only Mobile Earth Stations (ROMES) providing data communications operating in the 1 .pdf》由会员分享，可在线阅读，更多相关《ETSI EN 300 487-2016 Satellite Earth Stations and Systems (SES) Harmonised Standard for Receive-Only Mobile Earth Stations (ROMES) providing data communications operating in the 1 .pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 300 487 V2.1.2 (2016-11) Satellite Earth Stations and Systems (SES); Harmonised Standard for Receive-Only Mobile Earth Stations (ROMES) providing data communications operating in the 1,5 GHz frequency band; Radio Frequency (RF) specifications covering the essential requirements of article 3

2、.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 300 487 V2.1.2 (2016-11) 2 Reference REN/SES-00377 Keywords data, earth station, LMSS, MES, mobile, RO, satellite ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 1

3、6 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in pri

4、nt. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the P

5、ortable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/po

6、rtal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electro

7、nic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Teleco

8、mmunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM an

9、d the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 300 487 V2.1.2 (2016-11) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 7g

10、33 Definitions and abbreviations . 8g33.1 Definitions 8g33.2 Abbreviations . 8g34 Test conditions . 8g34.1 Test voltages . 8g34.2 Test report 8g34.3 Special Test Equipment (STE) . 9g34.4 Equipment Under Test (EUT) 9g35 RF emission limits 9g36 Receiver Performance Requirements . 9g36.1 General . 9g36

11、.2 Receiver Adjacent Channel Selectivity 10g36.2.1 Purpose . 10g36.2.2 Technical requirements . 10g36.2.3 Conformance test 10g36.3 Receiver Blocking Characteristics . 10g36.3.1 Purpose . 10g36.3.2 Technical requirements . 10g36.3.3 Conformance test 11g37 Method of Testing for Receiver Performance 11

12、g37.1 General . 11g37.2 Receiver Adjacent Channel Selectivity 11g37.2.1 General 11g37.2.2 Test arrangement 11g37.2.3 Test Procedures. 11g37.3 Receiver Blocking Characteristics . 12g37.3.1 General 12g37.3.2 Test arrangement 12g37.3.3 Test procedures. 12g3Annex A (normative): Environmental test condit

13、ions 13g3Annex B (normative): RF emissions - test procedure . 14g3B.1 Introduction 14g3B.2 Measuring apparatus. 14g3B.3 Equipment Under Test (EUT) 14g3B.4 Special Test Equipment (STE) . 14g3B.5 Measurement procedure . 14g3Annex C (normative): Relationship between the present document and the essenti

14、al requirements of Directive 2014/53/EU . 17g3ETSI ETSI EN 300 487 V2.1.2 (2016-11) 4 Annex D (informative): Bibliography . 18g3History 19g3ETSI ETSI EN 300 487 V2.1.2 (2016-11) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to E

15、TSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is avail

16、able from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 0

17、00 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Satellite Earth Stations and Systems (SES). The present document has been prepared unde

18、r the Commissions standardisation request C(2015) 5376 final i.1 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Di

19、rective 1999/5/EC i.2. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table C.1 confers, within the limits of the scope of the present document, a presumption of conformity

20、with the corresponding essential requirements of that Directive, and associated EFTA regulations. National transposition dates Date of adoption of this EN: 12 September 2016 Date of latest announcement of this EN (doa): 31 December 2016 Date of latest publication of new National Standard or endorsem

21、ent of this EN (dop/e): 30 June 2017 Date of withdrawal of any conflicting National Standard (dow): 30 June 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described

22、in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 300 487 V2.1.2 (2016-11) 6 Introduction The present document is intended to cover the provisions of D

23、irective 2014/53/EU i.2 (RE Directive) article 3.2 which states that “.radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference“. Recital 10 of Directive 2014/53/EU i.2 states that “in order to ensur

24、e that radio equipment uses the radio spectrum effectively and supports the efficient use of radio spectrum, radio equipment should be constructed so that: in the case of a transmitter, when the transmitter is properly installed, maintained and used for its intended purpose it generates radio waves

25、emissions that do not create harmful interference, while unwanted radio waves emissions generated by the transmitter (e.g. in adjacent channels) with a potential negative impact on the goals of radio spectrum policy should be limited to such a level that, according to the state of the art, harmful i

26、nterference is avoided; and, in the case of a receiver, it has a level of performance that allows it to operate as intended and protects it against the risk of harmful interference, in particular from shared or adjacent channels, and, in so doing, supports improvements in the efficient use of shared

27、 or adjacent channel“. Recital 11 of Directive 2014/53/EU i.2 states that “although receivers do not themselves cause harmful interference, reception capabilities are an increasingly important factor in ensuring the efficient use of radio spectrum by way of an increased resilience of receivers again

28、st harmful interference and unwanted signals on the basis of the relevant essential requirements of Union harmonisation legislation“. As a consequence, the present document includes both transmitting and receiving parameters aiming to maximize the efficient use of radio spectrum. ETSI ETSI EN 300 48

29、7 V2.1.2 (2016-11) 7 1 Scope The present document applies to the Receive-Only Mobile Earth Stations (ROMES) radio equipment operating under the Land Mobile Satellite Service (LMSS), in the frequency band 1 518 MHz to 1 559 MHz (space-to-earth bands). The ROMESs operate as part of a satellite system

30、providing one-way data communications. ROMESs could have several configurations, including: either Portable Equipment (PE) or vehicle Installed Equipment (IE); a number of modules including a display/control interface to the user. The present document is intended to cover the provisions of Directive

31、 2014/53/EU i.2 (RE Directive) article 3.2 which states that “radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference“. In addition to the present document, other ENs that specify technical requirem

32、ents in respect of essential requirements under other parts of article 3 of the Directive 2014/53/EU i.2 may apply to equipment within the scope of the present document. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or v

33、ersion number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be

34、found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 Void. 2 ETSI ETS 300 133

35、-5 (Edition 1) (07-1992): “Paging Systems (PS); Enhanced Radio MEssage System (ERMES); Part 5: Receiver conformance specification“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific refe

36、rences, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The followi

37、ng referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Sta

38、ndardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. ETSI ETSI EN 300 487 V2.1.2 (2016-11) 8 i.2 Directive 2014/53/EU of the European Parliament and of the Council of 16 Ap

39、ril 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: in-

40、band signals: signals which are located in the operating band plus an offset of 10 MHz outside this operating band operating frequency band: frequency band over which the ROMES is capable of operation 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: BW B

41、andWith CW Continuous Wave EC European Commission EFTA European Free Trade Association EIRP Equivalent Isotropically Radiated Power ETS European Telecommunication Standard EUT Equipment Under Test IE Installed EquipmentLMSS Land Mobile Satellite Service LTE Long Term Evolution MSS Mobile Satellite S

42、ervice PE Portable Equipment RF Radio Frequency ROMES Receive-Only Mobile Earth Station SNR Signal to Noise Ratio STE Special Test Equipment 4 Test conditions 4.1 Test voltages The nominal and extreme operational power supply voltages shall be stated by the manufacturer. 4.2 Test report The test rep

43、ort shall contain: the results of the tests; all parameters and operational conditions; the value of the highest frequency conversion oscillator. ETSI ETSI EN 300 487 V2.1.2 (2016-11) 9 4.3 Special Test Equipment (STE) To enable the tests specified in the present document to be carried out, the use

44、of STE, supplied by the manufacturer or system provider, may be necessary. Since the STE will be specific for the particular equipment, it is not possible to provide detailed specifications in the present doucment. However, the following baseline is provided: the STE shall enable the ROMES to tune t

45、o every channel in the operating frequency band, to enable spurious emissions to be measured; if the connection of the STE affects any of the parameters specified in the present doucment then the effects shall clearly be stated by the manufacturer. 4.4 Equipment Under Test (EUT) The EUT shall includ

46、e all units necessary for the intended operation. 5 RF emission limits Purpose: To protect terrestrial and satellite radio services from emissions caused by ROMESs to which the present document applies. Specification: The radiated power from the equipment, including its antenna, shall not exceed the

47、 limits in table 1. Table 1 Frequency range (MHz) (see note 1) EIRP limit (dBpW) (see note 1) Measurement bandwidth (kHz) 30,0 - 1 000,0 33 100 1 000,0 - 1 518,0 43 (see note 2) 100 1 518,0 - 1 559,0 17 3 1 559,0 - 12 750,0 43 (see note 2) 100 12 750,0 - 21 200,0 48 (see note 3) 100 21 200,0 - 40 00

48、0,0 60 100 NOTE 1: The lower limits shall apply at the transition frequency. NOTE 2: These figures shall be 48 dBpW prior to 1stJanuary 1997. NOTE 3: This figure shall be 54 dBpW prior to 1stJanuary 1997. Verification: All RF tests in this clause shall be carried out with the test conditions given i

49、n annex A. The equipment shall be tested according to the test procedure given in annex B. The upper frequency to which tests shall be performed shall be at least the 10thharmonic of the highest frequency conversion oscillator or ten times the highest operational frequency, whichever is greater. 6 Receiver Performance Requirements 6.1 General This clause shall apply for all ROMES. ETSI ETSI EN 300 487 V2.1.2 (2016-11) 10 6.2 Receiver Adjacent Channel Selectivity 6.2.1 Purpose To enable reception of a wanted signal in the presence of othe