EN ISO 8666-2016 en Small craft - Principal data《小工艺品-主要数据(ISO 8666 2016)》.pdf

《EN ISO 8666-2016 en Small craft - Principal data《小工艺品-主要数据(ISO 8666 2016)》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 8666-2016 en Small craft - Principal data《小工艺品-主要数据(ISO 8666 2016)》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO 8666:2016Small craft Principal data(ISO 8666:2016)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 8666:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 8666:2016.It supersedes BS EN ISO 8666:2002 which

2、 is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee GME/33, Small craft.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users

3、 are responsible for its correctapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 86250 2ICS 47.080Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theSta

4、ndards Policy and Strategy Committee on 31 August 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8666 August 2016 ICS 47.080 Supersedes EN ISO 8666:2002English Version Small craft - Principal data (ISO 8666:2016

5、) Petits navires - Donnes principales (ISO 8666:2016) Kleine Wasserfahrzeuge - Hauptdaten (ISO 8666:2016)This European Standard was approved by CEN on 26 May 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standa

6、rd the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English,

7、 French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulg

8、aria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tu

9、rkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.

10、Ref. No. EN ISO 8666:2016 EBS EN ISO 8666:2016EN ISO 8666:2016 (E) 3 European foreword This document (EN ISO 8666:2016) has been prepared by Technical Committee ISO/TC 188 ”Small craft”. This European Standard shall be given the status of a national standard, either by publication of an identical te

11、xt or by endorsement, at the latest by February 2017, and conflicting national standards shall be withdrawn at the latest by February 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held respo

12、nsible for identifying any or all such patent rights. This document supersedes EN ISO 8666:2002. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive. For relationship with

13、 EU Directive, see informative Annex ZA, which is an integral part of this document. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Re

14、public, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. En

15、dorsement notice The text of ISO 8666:2016 has been approved by CEN as EN ISO 8666:2016 without any modification. BS EN ISO 8666:2016EN ISO 8666:2016 (E) 4 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2013/53/EU This European Stand

16、ard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide one means of conforming to Essential Requirements of the New Approach Directive 2013/53/EU. Once this standard is cited in the Official Journal of the European Communities

17、 under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding Essential Requir

18、ements of that Directive and associated EFTA regulations. Table ZA.1 Correspondence between this European Standard and Directive 2013/53/EU Clause(s)/subclause(s) of this European Standard Essential requirements (ERs) of EU Directive 2013/53/EU Qualifying remarks/Notes 2, 3, 4, 5, 6, 7 Annex I This

19、European Standard establishes definitions for main dimensions and related data, mass specifications and loading conditions that may be required for the technical details of harmonized standards that provide a presumption of conformity with Directive 2013/53/EU. WARNING: Other requirements and other

20、EU Directives may be applicable to the products falling within the scope of this standard. BS EN ISO 8666:2016ISO 8666:2016(E)Foreword v1 Scope . 12 Terms and definitions . 13 Symbols, designations and units 24 Measurements . 34.1 General . 34.2 Longitudinal 44.2.1 General 44.2.2 Maximum length, Lma

21、x.44.2.3 Length of the hull, LH.44.2.4 Waterline length, LWL.74.3 Athwartship . 84.3.1 General 84.3.2 Maximum beam, Bmax84.3.3 Beam of hull, BH.84.3.4 Beam, waterline, BWL84.3.5 Maximum beam, waterline, BWLmax.84.3.6 Beam between hull centers, BCB84.4 Vertical . 94.4.1 Maximum depth, Dmax.94.4.2 Mid

22、ship depth, DLWL/2.94.4.3 Freeboard, F 104.4.4 Draught, T .104.4.5 Draught, air, Ha104.4.6 Headroom . 114.5 Other data . 114.5.1 Deadrise angle, .114.5.2 Reference sail area, AS.124.5.3 Standard sail area, AS124.5.4 Windage area, Alv124.5.5 Volume of the craft, V 125 Masses.135.1 Mass, net shipping,

23、 mN.135.2 Mass, gross shipping, mG135.3 Mass, light craft, mLC145.3.1 Items of equipment included in mLC145.3.2 Items of equipment and other items not included in mLC.155.4 Performance test mass, mP155.5 Mass of the craft when towed on a trailer, mT.165.5.1 General. 165.5.2 Items of equipment includ

24、ed in mT.165.5.3 Items of equipment not included in mT.185.5.4 Exclusions, inclusions .185.6 Maximum load, mML.186 Loading conditions 196.1 Test condition 196.2 Ready-for-use condition. 196.3 Fully loaded ready-for-use condition . 196.4 Empty craft condition 196.5 Light craft condition 206.6 Minimum

25、 operating condition 216.7 Loaded arrival condition . 21 ISO 2016 All rights reserved iiiContents PageBS EN ISO 8666:2016ISO 8666:2016(E)6.8 Maximum load condition 217 Tolerances 217.1 Published data 217.2 Preliminary specification 227.3 Reference lengths 22Bibliography .23iv ISO 2016 All rights res

26、ervedBS EN ISO 8666:2016ISO 8666:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member bod

27、y interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrote

28、chnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO

29、 documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held resp

30、onsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given

31、 for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following

32、URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 188, Small craft.This second edition cancels and replaces the first edition (ISO 8666:2002), which has been technically revised with the following main changes: definitions 2.7 to 2.13 have been added; lis

33、t of symbols in Table 1 has been extended; 4.3.5 and 4.3.6 have been added; 4.5.2, 4.5.3 and 4.5.4 have been added, and “projected sail area” has been deleted; 6.4 to 6.8 have been added; 7.1 has been modified and 7.3 added; clause on owners manual has been deleted. ISO 2016 All rights reserved vBS

34、EN ISO 8666:2016BS EN ISO 8666:2016Small craft Principal data1 ScopeThis International Standard establishes definitions of main dimensions and related data and of mass specifications and loading conditions. It applies to small craft having a length of the hull (LH) of up to 24 m.2 Terms and definiti

35、onsFor the purposes of this document, the following terms and definitions apply.NOTE For units, see Clause 3.2.1waterlineWLintersection line of the waters surface with the crafts hull when the craft (2.13) is afloat2.2maximum load waterlinereference waterlineWLrefwaterline (2.1) of the craft (2.13)

36、when upright in the maximum loaded displacement (2.5.1)2.3sheerlineintersection between deck and hull, for rounded deck edges the natural intersection, or, where no deck is fitted or the hull extends above the deck (bulwark), the upper edge of the crafts hullNote 1 to entry: The upper position of th

37、e sheerline depends on the inclination between the hull/deck intersection and the actual deck.2.4transom beamBTmaximum width of the hull at the transom at or below the sheerline (2.3), excluding extensions, handles and fittingsNote 1 to entry: Where spray rails act as chines or part of the planing s

38、urface, they are included in the transom beam measurement.Note 2 to entry: For craft (2.13) with a rounded or pointed stern or with a transom beam of less than half the maximum beam of the craft, the transom beam, BT, is the widest beam at or below the sheerline at the aft quarter length of the hull

39、.2.5displacementmass of water displaced by the craft (2.13), including all appendages2.5.1loaded displacementmLDCmass of water displaced by the craft (2.13), including all appendages, when in the fully loaded ready-for-use conditionNote 1 to entry: Fully loaded ready-for use condition is described i

40、n 6.3.INTERNATIONAL STANDARD ISO 8666:2016(E) ISO 2016 All rights reserved 1BS EN ISO 8666:2016ISO 8666:2016(E)2.5.2displacement volumeVDvolume of water displaced by the craft (2.13) that corresponds to the displacement (2.5)Note 1 to entry: Where the density of water used to calculate the volume of

41、 displacement is not salt water at a density of 1 025 kg/m3, the density of water used to calculate the volume of displacement is specified.2.6tank capacitynet usable volume of the tank(s) for the craft (2.13) in design trim (2.11) at rest at the maximum load waterline (2.2)2.7wing mastspar characte

42、rized by its cross-section which shows a smooth transition at the aft end into the sail, thus, contributing to its driving force2.8non-sailing boatcraft (2.13) for which the primary means of propulsion is other than by wind power, having reference sail area (2.10) (AS) 0,07 (mLDC)2/32.9sailing boatc

43、raft (2.13) for which the primary means of propulsion is by wind power, having reference sail area (2.10) (AS) 0,07 (mLDC)2/32.10reference sail areaASactual profile area of sails set abaft a mast, plus the maximum profile areas of all masts, plus reference triangle area(s) forward of each mast2.11de

44、sign trimlongitudinal attitude of the craft (2.13) when upright, with crew, fluids, stores, and equipment in the position(s) and load condition(s) designated by the designer or builder2.12underwaynot at anchor, or made fast to the shore, or aground2.13craftsmall craftrecreational boat, and other wat

45、ercraft using similar equipment, of up to 24 m length of hull (LH)3 Symbols, designations and unitsUnless specifically otherwise defined, the symbols, designations and units used in this International Standard are given in Table 1.Table 1 Symbols, designations and unitsSymbol Designation Unit Clause

46、AlVWindage area m24.5.4ASReference sail area m24.5.2ASStandard sail area m24.5.32 ISO 2016 All rights reservedBS EN ISO 8666:2016ISO 8666:2016(E)Symbol Designation Unit ClauseBCBBeam between hull centers m 4.3.6BHBeam of hull m 4.3.3BmaxMaximum beam m 4.3.2BWLBeam, waterline m 4.3.4BWLmaxMaximum bea

47、m, waterline m 4.3.5BTTransom beam m 2.4DmaxMaximum depth m 4.4.1DLWL/2Midship depth m 4.4.2F Freeboard m 4.4.3FAFreeboard, aft m 4.4.3.2FFFreeboard, forward m 4.4.3.4FMFreeboard, amidships m 4.4.3.3HaDraught, air m 4.4.5LHLength of the hull m 4.2.3LmaxMaximum length m 4.2.2LWLWaterline length m 4.2

48、.4mGGross shipping mass kg 5.2mLDCLoaded displacement kg 2.5.1mLCLight craft mass kg 5.3mNNet shipping mass kg 5.1mPPerformance test mass kg 5.4mTMass of craft when towed on trailer kg 5.5mMLMaximum load kg 5.6T Draught m 4.4.4TCDraught, canoe body m 4.4.4.4TmaxDraught, maximum m 4.4.4.2TminDraught,

49、 minimum m 4.4.4.3VDDisplacement volume m32.5.2V Volume of the craft m34.5.5VHVolume of the hull m34.5.5.2VSVolume of the superstructure m34.5.5.3WL Waterline 2.1WLrefMaximum load waterline 2.2 Deadrise angle degrees 4.5.14 Measurements4.1 GeneralMeasurements shall be established with the craft at rest at the maximum load waterline/reference waterline, WLref, unless otherwise stated.Table 1 (continued) ISO 2016 All rights reserved 3BS EN ISO 8666:2016ISO 8666:2016(E)4.2 Longitudinal4.2.1 GeneralThe lengths of a craft shall be measure