EN ISO 2411-2017 en Rubber- or plastics-coated fabrics - Determination of coating adhesion.pdf

《EN ISO 2411-2017 en Rubber- or plastics-coated fabrics - Determination of coating adhesion.pdf》由会员分享，可在线阅读，更多相关《EN ISO 2411-2017 en Rubber- or plastics-coated fabrics - Determination of coating adhesion.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、Rubber- or plastics-coated fabrics - Determination of coating adhesion (ISO 2411:2017)BS EN ISO 2411:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 2411 October 2017 ICS 59.080.40 Supersedes EN ISO 2411:20

2、00English Version Rubber- or plastics-coated fabrics - Determination of coating adhesion (ISO 2411:2017) Supports textiles revtus de caoutchouc ou de plastique - Dtermination de ladhrence du revtement (ISO 2411:2017) Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung der Haftfestigkei

3、t von Beschichtungen (ISO 2411:2017) This European Standard was approved by CEN on 28 August 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-t

4、o-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by transla

5、tion under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland,

6、 Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDI

7、ZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 2411:2017 ENational forewordThis British

8、 Standard is the UK implementation of EN ISO 2411:2017. It is identical to ISO 2411:2017. It supersedes BS EN ISO 2411:2000, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee TCI/24, Physical testing of textiles.A list of organizations represented on thi

9、s committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 92535 1ICS

10、59.080.40Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN IS

11、O 2411:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 2411 October 2017 ICS 59.080.40 Supersedes EN ISO 2411:2000English Version Rubber- or plastics-coated fabrics - Determination of coating adhesion (ISO 2411:2017) Supports textiles revtus de caoutchouc ou de plastique - Dtermination

12、de ladhrence du revtement (ISO 2411:2017) Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung der Haftfestigkeit von Beschichtungen (ISO 2411:2017) This European Standard was approved by CEN on 28 August 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations wh

13、ich stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This E

14、uropean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members

15、 are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

16、 Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in an

17、y form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 2411:2017 EBS EN ISO 2411:2017EN ISO 2411:2017 (E) 3 European foreword This document (EN ISO 2411:2017) has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products” in collaboration with Technical

18、 Committee CEN/TC 248 “Textiles and textile products” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2018, and conflicting national standards shall

19、be withdrawn at the latest by April 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 2411:2000. According to the

20、 CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hu

21、ngary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 2411:2017 has been approved by CEN as EN ISO 2411:2017 witho

22、ut any modification. ISO 2411:2017(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Atmosphere for conditioning and testing 24.1 For conditioning . 24.2 For testing . 25 Time-interval between manufacture and testing. 26 Preparation of test specimens 36.1 Gen

23、eral . 36.2 Method of preparation 1 . 36.3 Method of preparation 2 . 36.4 Determination of wet coating adhesion 46.4.1 End-use 46.4.2 Preparation of test specimens 46.4.3 Conducting the test 47 Apparatus . 48 Procedure. 59 Calculation and expression of results . 59.1 General . 59.2 Determination of

24、mid-point value 59.3 Calculation of mean result 59.4 Coating adhesion strength 610 Test report . 6Annex A (informative) Comments on interpretation of the autographic traces 11 ISO 2017 All rights reserved iiiContents PageBS EN ISO 2411:2017ISO 2411:2017(E)Foreword ivIntroduction v1 Scope . 12 Normat

25、ive references 13 Terms and definitions . 14 Atmosphere for conditioning and testing 24.1 For conditioning . 24.2 For testing . 25 Time-interval between manufacture and testing. 26 Preparation of test specimens 36.1 General . 36.2 Method of preparation 1 . 36.3 Method of preparation 2 . 36.4 Determi

26、nation of wet coating adhesion 46.4.1 End-use 46.4.2 Preparation of test specimens 46.4.3 Conducting the test 47 Apparatus . 48 Procedure. 59 Calculation and expression of results . 59.1 General . 59.2 Determination of mid-point value 59.3 Calculation of mean result 59.4 Coating adhesion strength 61

27、0 Test report . 6Annex A (informative) Comments on interpretation of the autographic traces 11 ISO 2017 All rights reserved iiiContents PageBS EN ISO 2411:2017ISO 2411:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO

28、member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern

29、mental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenan

30、ce are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention

31、 is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and

32、/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and e

33、xpressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 45, Rubber

34、and rubber products, Subcommittee SC 4, Products (other than hoses).This fourth edition cancels and replaces the third edition (ISO 2411:2000), which has been technically revised.The changes compared to the previous edition are as follows: a warning statement has been added before the scope; in Clau

35、se 2, the publication year of ISO 2231 has been added; in 3.1, the definition of delamination has been modified; a new Clause 4, specifying the atmosphere for conditioning and testing, has been added; in Clause 6, the dimension of test specimen has been revised according to the addition of the test

36、specimen of 20 mm width in 6.2 and 6.3.4 ; in both 6.3.1 and 6.3.3, a welding process has been added; in 6.2.3 and 6.3.1, notes have been changed to body text; in Clause 7, Grade B and precision 1 have been changed to class B and class 1, respectively, according to the updated references; in 9.2, N/

37、10 mm and N/20 mm have been added; in Clause 10, items a), f), and l) have been added; in Figure 3, x-axis and y-axis names have been added; in Figure 4, figure subtitles have been added.iv ISO 2017 All rights reservedBS EN ISO 2411:2017ISO 2411:2017(E)ForewordISO (the International Organization for

38、 Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the

39、right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedu

40、res used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial

41、rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights ide

42、ntified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation

43、 on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/fore

44、word.html.This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses).This fourth edition cancels and replaces the third edition (ISO 2411:2000), which has been technically revised.The changes compared to the previous editio

45、n are as follows: a warning statement has been added before the scope; in Clause 2, the publication year of ISO 2231 has been added; in 3.1, the definition of delamination has been modified; a new Clause 4, specifying the atmosphere for conditioning and testing, has been added; in Clause 6, the dime

46、nsion of test specimen has been revised according to the addition of the test specimen of 20 mm width in 6.2 and 6.3.4 ; in both 6.3.1 and 6.3.3, a welding process has been added; in 6.2.3 and 6.3.1, notes have been changed to body text; in Clause 7, Grade B and precision 1 have been changed to clas

47、s B and class 1, respectively, according to the updated references; in 9.2, N/10 mm and N/20 mm have been added; in Clause 10, items a), f), and l) have been added; in Figure 3, x-axis and y-axis names have been added; in Figure 4, figure subtitles have been added.iv ISO 2017 All rights reserved ISO

48、 2411:2017(E)IntroductionKnowledge of the strength of adhesion between the coating and the adjacent layer is important as an inadequate adhesion strength can often result in failure of the product due to delamination. ISO 2017 All rights reserved vBS EN ISO 2411:2017Rubber- or plastics-coated fabric

49、s Determination of coating adhesionWARNING Persons using this document should be familiar with normal laboratory practice. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions.1 ScopeThis document specifies a method of determining the coating adhesion strength of coated fabrics.2 Normative referencesThe following docu