EN 62149-1-2012 en Fibre optic active components and devices - Performance standards - Part 1 General and guidance.pdf

《EN 62149-1-2012 en Fibre optic active components and devices - Performance standards - Part 1 General and guidance.pdf》由会员分享，可在线阅读，更多相关《EN 62149-1-2012 en Fibre optic active components and devices - Performance standards - Part 1 General and guidance.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationFibre optic active componentsand devices Performance standardsPart 1: General and guidanceBS EN 62149-1:2012National forewordThis British Standard is the UK implementation of EN

2、62149-1:2012. It isidentical to IEC 62149-1:2011. It supersedes BS EN 62149-1:2004 which iswithdrawn.The UK participation in its preparation was entrusted by Technical CommitteeGEL/86, Fibre optics, to Subcommittee GEL/86/3, Fibre optic systems andactive devices.A list of organizations represented o

3、n this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 580 75987 1IC

4、S 33.180.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 May 2012.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 62149-1:

5、2012EUROPEAN STANDARD EN 62149-1 NORME EUROPENNE EUROPISCHE NORM February 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2012

6、CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 62149-1:2012 E ICS 33.180.01 Supersedes EN 62149-1:2004English version Fibre optic active components and devices - Performance standards - Part 1: General and guidance (IEC 62149-1:2

7、011) Composants et dispositifs actifs fibres optiques - Normes de performances - Partie 1: Gnralits et lignes directrices (CEI 62149-1:2011) Aktive Lichtwellenleiterbauelemente und -gerte - Betriebsverhaltensnormen - Teil 1: Allgemeines und Leitfaden (IEC 62149-1:2011) This European Standard was app

8、roved by CENELEC on 2012-01-11. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nat

9、ional standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its

10、own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, I

11、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 62149-1:2012EN 62149-1:2012 - 2 - Foreword The text of document 86C/1016/CDV, future edition 2 of IEC

12、 62149-1, prepared by SC 86C “Fibre optic systems and active devices“, of IEC/TC 86, “Fibre optics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62149-1:2012. The following dates are fixed: latest date by which the document has to be implemented at national level by p

13、ublication of an identical national standard or by endorsement (dop) 2012-10-11 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-01-11 This document supersedes EN 62149-1:2004. EN 62149-1:2012 includes the following significant technical chang

14、es with respect to EN 62149-1:2004: The technical change consists of an update in Table A.1. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent r

15、ights. Endorsement notice The text of the International Standard IEC 62149-1:2011 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61300 series NOTE Harmonized in

16、EN 61300 series (not modified). IEC 61751 IEC 62005 series NOTE Harmonized as EN 61751. NOTE Harmonized in EN 62005 series (not modified). BS EN 62149-1:2012- 3 - EN 62149-1:2012 Annex ZA (normative) Normative references to international publications with their corresponding European publications Th

17、e following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When

18、 an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60068-2-27 - Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock EN 60068-2-27 - IEC 61300-2-1 - Fibre optic interconnecti

19、ng devices and passive components - Basic test and measurement procedures - Part 2-1: Tests - Vibration (sinusoidal) EN 61300-2-1 - IEC 61300-2-4 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-4: Tests - Fibre/cable retention EN 61300-2-

20、4 - IEC 61300-2-5 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-5: Tests - Torsion EN 61300-2-5 - IEC 61300-2-9 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-9: Tests - Sho

21、ck EN 61300-2-9 - IEC 61300-2-17 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-17: Tests - Cold EN 61300-2-17 - IEC 61300-2-18 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2

22、-18: Tests - Dry heat - High temperature endurance EN 61300-2-18 - IEC 61300-2-19 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-19: Tests - Damp heat (steady state) EN 61300-2-19 - IEC 61300-2-21 - Fibre optic interconnecting devices an

23、d passive components - Basic test and measurement procedures - Part 2-21: Tests - Composite temperature/humidity cyclic test EN 61300-2-21 - IEC 61300-2-22 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-22: Tests - Change of temperature

24、EN 61300-2-22 - BS EN 62149-1:2012EN 62149-1:2012 - 4 - Publication Year Title EN/HD Year IEC 61300-2-26 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-26: Tests - Salt mist EN 61300-2-26 - IEC 61300-2-27 - Fibre optic interconnecting de

25、vices and passive components - Basic test and measurement procedures - Part 2-27: Tests - Dust - Laminar flow EN 61300-2-27 - IEC 61300-2-28 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-28: Tests - Industrial atmosphere (sulphur dioxid

26、e) EN 61300-2-28 - IEC 61300-2-42 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-42: Tests - Static side load for connectors EN 61300-2-42 - IEC 61300-2-44 - Fibre optic interconnecting devices and passive components - Basic test and mea

27、surement procedures - Part 2-44: Tests - Flexing of the strain relief of fibre optic devices EN 61300-2-44 - IEC 61300-2-45 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-45: Tests - Durability test by water immersion EN 61300-2-45 - IEC

28、 61300-2-46 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-46: Tests - Damp heat cyclic EN 61300-2-46 - IEC 61300-2-48 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-48: Test

29、s - Temperature-humidity cycling EN 61300-2-48 - BS EN 62149-1:2012 2 62149-1 IEC:2011 CONTENTS INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 7 4 Preparation of a performance standard . 7 4.1 General . 7 4.2 Product definition 7 4.3 Tests . 7 4.4 Details . 8 4.5 R

30、equirements 8 4.6 Sample size 8 4.7 Groupings/sequences 8 4.8 Pass/fail criteria 8 4.9 Reference product definition 8 4.10 Performance standard test report 8 4.11 Environmental aspects 9 Annex A (normative) Tests and severities for performance standards 10 Bibliography 14 Table A.1 General operating

31、 service environments and definitions . 10 Table A.2 Category C Controlled environment . 11 Table A.3 Category U Uncontrolled environment . 11 Table A.4 Category O Outside plant environment 12 Table A.5 Category E Extreme environment 13 BS EN 62149-1:201262149-1 IEC:2011 5 INTRODUCTION Performance s

32、tandards define standard electro-optical performance under a set of prescribed conditions and contain a series or a set of tests and measurements (which may or may not be grouped into a specific schedule) with clearly defined conditions, severities and pass/fail criteria. The tests are intended to b

33、e run on as an initial design verification to prove the products ability to satisfy the requirements of a specific application, market sector or user group. The subsequent parts of this document contain those sets of performance criteria that have been standardised for international use. A product t

34、hat has been shown to meet all the requirements of a performance standard may be declared as complying with that performance standard. Products from one manufacturer that are tested to a performance standard will operate together within the bounds of the criteria set by the performance standard. The

35、re is however no guarantee that products from different suppliers having the same standard interface, which have been independently tested to a performance standard, will meet the same levels of optical performance when mated together as those supplied by one manufacturer. Compliance with a performa

36、nce standard demonstrates that a product has in essence passed a design verification test, it is not a guarantee of lifetime assured performance nor reliability. Both service life tests and reliability testing must be the subject of a separate test schedule where the tests and severities selected ar

37、e such that they are truly representative of the requirements of these test programmes. Consistency of manufacture should be maintained using a recognised quality assurance programme while the reliability of the product should be evaluated using the procedures recommended in IEC 62005 and IEC 61751.

38、 Where possible, tests and measurements should be selected from IEC 61300. Where this is not possible, the required test method shall be attached as an annex to the performance standard. BS EN 62149-1:2012 6 62149-1 IEC:2011 FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES PERFORMANCE STANDARDS Part 1: Gen

39、eral and guidance 1 Scope This part of IEC 62149 provides references, definitions and rules for creating active fibre optic device performance standards, as well as related information pertinent to the subject. Subsequent parts of IEC 62149 are sequentially numbered and contain performance criteria

40、for specific applications. Each part will be added as the performance criteria become standardised for international use. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references,

41、only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-2-27, Environmental testing Part 2-27: Tests Test Ea and guidance: Shock IEC 61300-2-1, Fibre optic interconnecting devices and passive components Basic

42、 test and measurement procedures Part 2-1: Tests Vibration (sinusoidal) IEC 61300-2-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-4: Tests Fibre/cable retention IEC 61300-2-5, Fibre optic interconnecting devices and passive components Basi

43、c test and measurement procedures Part 2-5: Tests Torsion IEC 61300-2-9, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-9: Tests Shock IEC 61300-2-17, Fibre optic interconnecting devices and passive components Basic test and measurement proced

44、ures Part 2-17: Tests Cold IEC 61300-2-18, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-18: Tests Dry heat High temperature endurance IEC 61300-2-19, Fibre optic interconnecting devices and passive components Basic test and measurement proce

45、dures Part 2-19: Tests Damp heat (steady state) IEC 61300-2-21, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-21: Tests Composite temperature/humidity cyclic test IEC 61300-2-22, Fibre optic interconnecting devices and passive components Basi

46、c test and measurement procedures Part 2-22: Tests Change of temperature IEC 61300-2-26, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-26: Tests Salt mist BS EN 62149-1:201262149-1 IEC:2011 7 IEC 61300-2-27, Fibre optic interconnecting device

47、s and passive components Basic test and measurement procedures Part 2-27: Tests Dust Laminar flow IEC 61300-2-28, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-28: Tests Industrial atmosphere (sulphur dioxide) IEC 61300-2-42, Fibre optic inte

48、rconnecting devices and passive components Basic test and measurement procedures Part 2-42: Tests Static side load for connectors IEC 61300-2-44, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-44: Tests Flexing of the strain relief of fibre op

49、tic devices IEC 61300-2-45, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-45: Tests Durability test by water immersion IEC 61300-2-46, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-46: Tests Damp heat, cyclic IEC 61300-2-48, Fibre optic interconnecting devices and passive components Bas