EN 61000-4-4-2012 en Electromagnetic compatibility (EMC) - Part 4-4 Testing and measurement techniques - Electrical fast transient burst immunity test.pdf

《EN 61000-4-4-2012 en Electromagnetic compatibility (EMC) - Part 4-4 Testing and measurement techniques - Electrical fast transient burst immunity test.pdf》由会员分享，可在线阅读，更多相关《EN 61000-4-4-2012 en Electromagnetic compatibility (EMC) - Part 4-4 Testing and measurement techniques - Electrical fast transient burst immunity test.pdf（47页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationElectromagnetic compatibility (EMC)Part 4-4: Testing and measurement techniques Electrical fast transient/burst immunity testBS EN 61000-4-4:2012National forewordThis British Sta

2、ndard is the UK implementation of EN 61000-4-4:2012. It is identical to IEC 61000-4-4:2012. It supersedes BS EN 61000-4-4:2004+A1:2010 which will be withdrawn on 4 June 2015.The UK participation in its preparation was entrusted by Technical Committee GEL/210, EMC - Policy committee, to Subcommittee

3、GEL/210/12, EMC basic, generic and low frequency phenomena Standardization.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct

4、application. The British Standards Institution 2012.Published by BSI Standards Limited 2012 ISBN 978 0 580 69361 8 ICS 33.100.20 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Stand-ards Policy and Strat

5、egy Committee on 30 November 2012.Amendments issued since publicationDate Text affectedBRITISH STANDARDBS EN 61000-4-4:2012EUROPEAN STANDARD EN 61000-4-4 NORME EUROPENNE EUROPISCHE NORM November 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Elect

6、rotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61000-4-4:2012 E ICS 33.100.20 Supersedes EN 61000-4-4:2004 +

7、 A1:2010English version Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test (IEC 61000-4-4:2012) Compatibilit lectromagntique (CEM) - Partie 4-4: Techniques dessai et de mesure - Essai dimmunit aux transitoires lectriques

8、 rapides en salves (CEI 61000-4-4:2012) Elektromagnetische Vertrglichkeit (EMV) - Teil 4-4: Prf- und Messverfahren - Prfung der Strfestigkeit gegen schnelle transiente elektrische Strgren/Burst (IEC 61000-4-4:2012) This European Standard was approved by CENELEC on 2012-06-04. CENELEC members are bou

9、nd to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the C

10、EN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management

11、 Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland,

12、 Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 61000-4-4:2012EN 61000-4-4:2012 - 2 - Foreword The text of document 77B/670/FDIS, future edition 3 of IEC 61000-4-4,

13、prepared by SC 77B “High frequency phenomena” of IEC/TC 77 “Electromagnetic compatibility“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61000-4-4:2012. The following dates are fixed: latest date by which the document has to be implemented at national level by publicat

14、ion of an identical national standard or by endorsement (dop) 2013-05-09 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-06-04 This document supersedes EN 61000-4-4:2004 + A1:2010. EN 61000-4-4:2012 includes the following significant technica

15、l changes with respect to EN 61000-4-4:2004 + A1:2010: This edition improves and clarifies simulator specifications, test criteria and test setups. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be he

16、ld responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61000-4-4:2012 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the

17、standards indicated: IEC 61000-4-2:2008 NOTE Harmonised as EN 61000-4-2:2009 (not modified). IEC 61000-4-4:2004 NOTE Harmonised as EN 61000-4-4:2004 (not modified). IEC 61000-4-4:2004/A1:2010 NOTE Harmonised as EN 61000-4-4:2004/A1:2010 (not modified). IEC 61000-4-5:2005 NOTE Harmonised as EN 61000-

18、4-5:2006 (not modified). BS EN 61000-4-4:2012- 3 - EN 61000-4-4:2012 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable

19、for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/H

20、D applies. Publication Year Title EN/HD Year IEC 60050-161 1990 International Electrotechnical Vocabulary (IEV) - Chapter 161: Electromagnetic compatibility - - BS EN 61000-4-4:2012 2 61000-4-4 IEC:2012 CONTENTS INTRODUCTION . 6 1 Scope . 7 2 Normative references . 7 3 Terms, definitions and abbrevi

21、ations 7 3.1 Terms and definitions 7 3.2 Abbreviations 10 4 General 10 5 Test levels 10 6 Test equipment . 11 6.1 Overview . 11 6.2 Burst generator . 11 6.2.1 General . 11 6.2.2 Characteristics of the fast transient/burst generator . 12 6.2.3 Calibration of the characteristics of the fast transient/

22、burst generator 14 6.3 Coupling/decoupling network for a.c./d.c. power port . 15 6.3.1 Characteristics of the coupling/decoupling network 15 6.3.2 Calibration of the coupling/decoupling network 16 6.4 Capacitive coupling clamp . 17 6.4.1 General . 17 6.4.2 Calibration of the capacitive coupling clam

23、p 18 7 Test setup 20 7.1 General . 20 7.2 Test equipment . 20 7.2.1 General . 20 7.2.2 Verification of the test instrumentation . 20 7.3 Test setup for type tests performed in laboratories 21 7.3.1 Test conditions 21 7.3.2 Methods of coupling the test voltage to the EUT 24 7.4 Test setup for in situ

24、 tests . 26 7.4.1 Overview . 26 7.4.2 Test on power ports and earth ports 26 7.4.3 Test on signal and control ports . 27 8 Test procedure . 28 8.1 General . 28 8.2 Laboratory reference conditions 28 8.2.1 Climatic conditions 28 8.2.2 Electromagnetic conditions 28 8.3 Execution of the test 28 9 Evalu

25、ation of test results 29 10 Test report 29 Annex A (informative) Information on the electrical fast transients . 30 Annex B (informative) Selection of the test levels 32 Annex C (informative) Measurement uncertainty (MU) considerations . 34 Bibliography 43 BS EN 61000-4-4:201261000-4-4 IEC:2012 3 Fi

26、gure 1 Simplified circuit diagram showing major elements of a fast transient/burst generator 12 Figure 2 Representation of an electrical fast transient/burst . 13 Figure 3 Ideal waveform of a single pulse into a 50 load with nominal parameters tr= 5 ns and tw = 50 ns 13 Figure 4 Coupling/decoupling

27、network for a.c./d.c. power mains supply ports/terminals 16 Figure 5 Calibration of the waveform at the output of the coupling/decoupling network 17 Figure 6 Example of a capacitive coupling clamp . 18 Figure 7 Transducer plate for coupling clamp calibration 19 Figure 8 Calibration of a capacitive c

28、oupling clamp using the transducer plate 19 Figure 9 Block diagram for electrical fast transient/burst immunity test . 20 Figure 10 Example of a verification setup of the capacitive coupling clamp 21 Figure 11 Example of a test setup for laboratory type tests 22 Figure 12 Example of test setup using

29、 a floor standing system of two EUTs. 23 Figure 13 Example of a test setup for equipment with elevated cable entries . 24 Figure 14 Example of a test setup for direct coupling of the test voltage to a.c./d.c. power ports for laboratory type tests . 25 Figure 15 Example for in situ test on a.c./d.c.

30、power ports and protective earth terminals for stationary, floor standing EUT 26 Figure 16 Example of in situ test on signal and control ports without the capacitive coupling clamp 27 Table 1 Test levels. 11 Table 2 Output voltage peak values and repetition frequencies 15 Table C.1 Example of uncert

31、ainty budget for voltage rise time (tr) . 36 Table C.2 Example of uncertainty budget for EFT/B peak voltage value (VP) . 37 Table C.3 Example of uncertainty budget for EFT/B voltage pulse width (tw) . 38 Table C.4 factor (Equation (C.4) of different unidirectional impulse responses corresponding to

32、the same bandwidth of the system B 40 BS EN 61000-4-4:2012 6 61000-4-4 IEC:2012 INTRODUCTION IEC 61000 is published in separate parts, according to the following structure: Part 1: General General considerations (introduction, fundamental principles) Definitions, terminology Part 2: Environment Desc

33、ription of the environment Classification of the environment Compatibility levels Part 3: Limits Emission limits Immunity limits (in so far as they do not fall under the responsibility of the product committees) Part 4: Testing and measurement techniques Measurement techniques Testing techniques Par

34、t 5: Installation and mitigation guidelines Installation guidelines Mitigation methods and devices Part 6: Generic standards Part 9: Miscellaneous Each part is further subdivided into several parts, published either as international standards or as technical specifications or technical reports, some

35、 of which have already been published as sections. Others are published with the part number followed by a dash and a second number identifying the subdivision (example: IEC 61000-6-1). This part is an international standard which gives immunity requirements and test procedures related to electrical

36、 fast transients/bursts. BS EN 61000-4-4:201261000-4-4 IEC:2012 7 ELECTROMAGNETIC COMPATIBILITY (EMC) Part 4-4: Testing and measurement techniques Electrical fast transient/burst immunity test 1 Scope This part of IEC 61000 relates to the immunity of electrical and electronic equipment to repetitive

37、 electrical fast transients. It gives immunity requirements and test procedures related to electrical fast transients/bursts. It additionally defines ranges of test levels and establishes test procedures. The object of this standard is to establish a common and reproducible reference in order to eva

38、luate the immunity of electrical and electronic equipment when subjected to electrical fast transient/bursts on supply, signal, control and earth ports. The test method documented in this part of IEC 61000 describes a consistent method to assess the immunity of an equipment or system against a defin

39、ed phenomenon. NOTE As described in IEC Guide 107, this is a basic EMC publication for use by product committees of the IEC. As also stated in Guide 107, the IEC product committees are responsible for determining whether this immunity test standard is applied or not, and if applied, they are respons

40、ible for determining the appropriate test levels and performance criteria.1The standard defines: test voltage waveform; range of test levels; test equipment; calibration and verification procedures of test equipment; test setups; test procedure. The standard gives specifications for laboratory and i

41、n situ tests. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (inclu

42、ding any amendments) applies. IEC 60050-161:1990, International Electrotechnical Vocabulary Chapter 161: Electromagnetic compatibility 3 Terms, definitions and abbreviations 3.1 Terms and definitions For the purposes of this document, the terms and definitions of IEC 60050-161, as well as the follow

43、ing apply. 1TC 77 and its subcommittees are prepared to co-operate with product committees in the evaluation of the value of particular immunity tests for their products. BS EN 61000-4-4:2012 8 61000-4-4 IEC:2012 NOTE Several of the most relevant terms and definitions from IEC 60050-161 are presente

44、d among the definitions below. 3.1.1 auxiliary equipment AE equipment necessary to provide the equipment under test (EUT) with the signals required for normal operation and equipment to verify the performance of the EUT 3.1.2 burst sequence of a limited number of distinct pulses or an oscillation of

45、 limited duration SOURCE: IEC 60050-161:1990, 161-02-07 3.1.3 calibration set of operations which establishes, by reference to standards, the relationship which exists, under specified conditions, between an indication and a result of a measurement Note 1 to entry: This term is based on the “uncerta

46、inty“ approach. Note 2 to entry: The relationship between the indications and the results of measurement can be expressed, in principle, by a calibration diagram. SOURCE: IEC 60050-311:2001, 311-01-09 3.1.4 coupling interaction between circuits, transferring energy from one circuit to another 3.1.5

47、common mode (coupling) simultaneous coupling to all lines versus the ground reference plane 3.1.6 coupling clamp device of defined dimensions and characteristics for common mode coupling of the disturbance signal to the circuit under test without any galvanic connection to it 3.1.7 coupling network

48、electrical circuit for the purpose of transferring energy from one circuit to another 3.1.8 decoupling network electrical circuit for the purpose of preventing EFT voltage applied to the EUT from affecting other devices, equipment or systems which are not under test 3.1.9 degradation (of performance

49、) undesired departure in the operational performance of any device, equipment or system from its intended performance Note 1 to entry: The term “degradation“ can apply to temporary or permanent failure. SOURCE: IEC 60050-161:1990, 161-01-19 3.1.10 EFT/B electrical fast transient/burst BS EN 61000-4-4:201261000-4-4 IEC:2012 9 3.1.11 electromagnetic compatibility EMC ability of an equipment or system to function satisfactorily in its elect