EN 60835-3-14-1996 en Methods of Measurement for Equipment Used in Digital Microwave Radio Transmission Systems Part 3 Measurements on Satellite Earth Stations Section 14 Earth Sta.pdf

《EN 60835-3-14-1996 en Methods of Measurement for Equipment Used in Digital Microwave Radio Transmission Systems Part 3 Measurements on Satellite Earth Stations Section 14 Earth Sta.pdf》由会员分享，可在线阅读，更多相关《EN 60835-3-14-1996 en Methods of Measurement for Equipment Used in Digital Microwave Radio Transmission Systems Part 3 Measurements on Satellite Earth Stations Section 14 Earth Sta.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、lb2Libb 0587151 545 BRITISH STANDARD Methods of measurement for equipment used in digital microwave radio transmission systems Part 3. Measurements on satellite earth stations Section 3.14 Earth stations for satellite news gathering (SNG) c * Kn The European Standard EN 60835-314 : 1996 has the stat

2、us of a British Standard ICs 33.060.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHI LAW it should then be confirmed that the received cross-polarized signal level is lower than the level correspond- ing to the specified cross-polarization discrimination. If required, a test sig

3、nal is then transmitted from the SNG terminal to the satellite, under the direction of the cooperating earth station, and the correct antenna alignment of the SNG terminal is verified by confirming that the cross-polarized signal level received by the Co-operating earth station is lower than the lev

4、el corresponding to the specified cross- polarization discrimination. NOTE - This measurement should be carried out at a frequency at which no other cross-polar signal is transmitted. 5.1.3 Carrier frequencies See IEC 835-1 -2. The frequency of the carrier transmitting the vision and sound signals s

5、hall be measured by switching off the modulation. Measurements shall be carried out at specified steps of the frequency-agile up-converter 1, and the deviation between the measured and nominal frequencies shall be ascertained. The microwave counter for this measurement shall be connected to the low-

6、level output of the coupler following the HPA, as shown in figure 2. 5.1.4 RF output power See IEC 835-1-2. A power meter should be connected to the r.f. output port by disconnecting the antenna waveguide. For an SNG terminal with digital modulation, the output power of the carrier shall be measured

7、, and, if required, the mean output power of the signal modulated, preferably by a pseudo-noise bit sequence. For an SNG terminal with analogue modulation, the unmodulated carrier power shall be measured. The range of output power adjustment, if applicable, should also be ascertained. . When multipl

8、e carriers are transmitted simultaneously from a single power amplifier, the power of each carrier shall be measured separately by using a calibrated spectrum analyzer. 5.1.5 RF output spectrum See IEC 835-1-2. With a spectrum analyzer connected to the low-level test output port of the coupler shown

9、 in figure 2, the spectrum shall be measured at the rated output power, with the operational carrier modulated by a suitable test signal. A mask should be applied to the spectrum analyzer screen to ascertain that spectrum lines are confined within specified limits. = lb24bb9 05871bL 479 =- Page 7 EN

10、 60835-3-14 : 1996 5.1.6 Radiation hazards The purpose of this measurement is to ensure that the r.f. electromagnetic fields radiated from the SNG equipment do not constitute a potential hazard to operators, or to the general public. The SNG installation shall be approached from all accessible direc

11、tions, and measurements shall be taken of the power flux density by using a calibrated test antenna connected to a receiver (hazard meter). All locations where a specified power flux density is exceeded shall be identified. 5.1 .? See the future IEC 835-3-13. Off-axis EIRP (equivalent isotropically

12、radiated power) density 5.1.8 G/T of the monitoring system See IEC 835-3-7. The purpose of measuring this parameter is to ascertain that the monitored picture and sound signals characterize, to a sufficient extent, the uplinked picture and sound signals. 5.2 Baseband parameters 5.2.1 Interface param

13、eters of the sound/vision equipment See IEC 835-1-2. 5.2.2 Control functions - antenna alignment, azimuth and elevation. including antenna tracking, if applicable; - polarization; - carrier power; - carrier frequency (by synthesizer tuning); - transmitter output power (onioff). In a basic flyaway sy

14、stem, all these functions may be manually controlled. In an SNG vehicle, some of these functions, for example antenna and polarization adjustments, may be operated by remote control. It should be verified that the above control functions operate as specified. 5.2.3 Video/sound parameters The video a

15、nd sound parameters shall be tested in a transmitterlreceiver loop utilizing the loop test translator shown in figure 2. A test receiver of suitable quality shall be applied if these parameters cannot be accurately assessed in the transmitter/receiver loop because of the insufficient quality of the

16、SNG terminal receiving part. 5.2.4 Duplex sound communication channels These channels shall also be checked in a transmitterlreceiver loop utilizing the loop test translator. A functional check shall be carried out by initiating a call, and verifying that connection with the called party has been es

17、tablished. Page 8 EN 60835-3-14 : 1996 5.3 Power supply system The purpose of testing the power supply system is to confirm, under specified variations of supply input voltage and frequency, relevant performance parameters such as output power, spurious signals, transmit frequency, etc. 6 Reference

18、documents ITU-R Recommendation SNG 770: 1994, Uniform operational and control procedures for satellite news gathering (SNG) ITU-R Recommendation SNG 771 -1 : 1994, Auxiliary coordination satellite circuits for SNG terminals ITU-R Recommendation SNG 722-1 : 1994, Uniform technical standards (analogue

19、) r“3r satellite news gathering (SNG) LbZqbbS 0587363 2b7 Page 9 EN 60835-3-14 : 1996 am aa .- - c L 3 U L a z u) d 5 Page 10 EN 60835-3-14 : 1996 I I 61 - I - u. I i - Lb2Libb 0587Lb5 03T W Page 11 EN 60835-3-14 : 1996 Annex ZA (normative) Normative references to international publications with the

20、ir corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendme

21、nts to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). NOTE. When an international publication has been modified b

22、y Common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year IEC 8351-2 1992 IEC 8353-2 1995 IEC 835-3-7 1995 IEC 835-3-13 : 1996 Title Methods of measurement for equipment used in digital microwave radio transmission systems Part 1: Measurements common to terrastrial rad

23、io-relay systems and satellite earth stations Section 2: Basic chamtemstics Section 2: Antenna Part 3: Measurements on satellite earn stations Section 7: Figure-of-merit of receiving systern Ssctwn 13: VSATsystems EN/iD Year EN 608351-2 1993 EN 608353-2 1996 EN 60835-3-7 1995 EN 608353-13 1996 O BSI

24、 1997 List of references See national foreword. OBSI 1997 BS EN 1997 BS 7573 : Section 3.14 : 1997 IEC 835-3-14 : 1996 60835-3-14 : BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presen

25、ts the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Revisi

26、ons British Standards are updated by amendment or revision. Users of British Standards should make SLUP that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quahty of our products and services. We would be grateful if anyone finding an inaccuracy or ambig

27、uity while using this British Standard would inform the Secretary of the responsible technical committee, the identity of which can be found on the inside front cover. Tel 0181 996 9000; Fax: 0181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers

28、automatically receive the latest editions of standards. Buying standards Orders for ail BSI, international and foreign standards publications should be addressed to Customer Services, Sales Department at Chiswick Tel O181 996 7000; Fax: O181 996 7001. In response to orders for international standard

29、s, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library, the Standardline Database,

30、 the BSI Information Technology Service (BITS) and its Technical Help to Exporters Service. Contact the Information Department at Chiswick Tel 0181 996 7111; Fax O181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchas

31、e price of standards. For details of these and other benefits contact Customer Services, Membership at Chiswick Tel O181 996 7002; Fax: 0181 996 7001. Copyright Copyright subsists in ail BSI publications. BSI also holds the copyright, in the UK, of the publications of the intematiod standardization

32、bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior Written permission from BSI. This does not preclude t

33、he free use, in the com of implementing the standard, of necessary dem such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained If permission is granted, the tem may include royalty payments or a licensing agreement. Details and advice can be obtained nom the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4AL. ISBN O 880 26933 7 EPW125