EN 16027-2011 en Protective clothing - Gloves with protective effect for association football goal keepers《防护服 足球守门员的具有保护作用的手套》.pdf

《EN 16027-2011 en Protective clothing - Gloves with protective effect for association football goal keepers《防护服 足球守门员的具有保护作用的手套》.pdf》由会员分享，可在线阅读，更多相关《EN 16027-2011 en Protective clothing - Gloves with protective effect for association football goal keepers《防护服 足球守门员的具有保护作用的手套》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 16027:2011Protective clothing Gloveswith protective effect forassociation football goalkeepersBS EN 16027:2011 BRITISH STANDARDNational forewordThis British Standard is the

2、 UK implementation of EN 16027:2011. The UK participation in its preparation was entrusted to TechnicalCommittee PH/3/11, Protective Equipment For Sports Players. A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to inc

3、lude all the necessary provi-sions of a contract. Users are responsible for its correct application. The British Standards Institution 2012ISBN 978 0 580 68627 6ICS 13.340.40Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the

4、authority of the Standards Policy and Strategy Committee on 31 January 2012.Amendments issued since publicationDateText affectedBS EN 16027:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16027 December 2011 ICS 13.340.40 English Version Protective clothing - Gloves with protective effect f

5、or association football goal keepers Vtements de protection - Gants effet protecteur pour gardiens de but de football Schutzkleidung - Handschuhe mit Schutzwirkung fr Fuballtorwarte This European Standard was approved by CEN on 29 October 2011. CEN members are bound to comply with the CEN/CENELEC In

6、ternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to a

7、ny CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official

8、versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia

9、, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for

10、 CEN national Members. Ref. No. EN 16027:2011: EBS EN 16027:2011EN 16027:2011 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 Terms and definitions .54 Requirements .54.1 General 54.2 Innocuousness .54.3 Ergonomics 64.4 Stiffness 64.5 Restraint system 64.6 Impact stre

11、ngth 64.7 Sizing 65 Test methods 65.1 General 65.2 Sampling and conditioning .75.3 Ergonomics 75.4 Stiffness 75.4.1 Apparatus .75.4.2 Procedure 105.5 Restraint 115.6 Impact strength . 125.6.1 Apparatus 125.6.2 Procedure 136 Marking 147 Information supplied by the manufacturer 14Annex A (informative)

12、 Environmental Aspects . 16Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 89/686/EEC . 17Bibliography . 18BS EN 16027:2011EN 16027:2011 (E) 3 Foreword This document (EN 16027:2011) has been prepared by Technical Committee CEN/TC 162

13、“Protective clothing including hand and arm protection and lifejackets”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2012, and conflicting nationa

14、l standards shall be withdrawn at the latest by June 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prep

15、ared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Inte

16、rnal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem

17、bourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 16027:2011EN 16027:2011 (E) 4 Introduction Whilst many types of gloves for goal keepers are only designed to facilitate catching the ball and provide cushioning

18、from minor contusions, gloves can also be designed to provide additional protection to the hands and particularly the fingers. These are intended to reduce the risk of fractures, by restricting the flexing under impact of joints beyond their natural range of movement. BS EN 16027:2011EN 16027:2011 (

19、E) 5 1 Scope This European Standard applies to gloves for goal keepers for association football (in the following text just “gloves for goal keepers“) with stabilizing and/or stiffening elements (e.g. splint, brace), which due to their construction, provide a protective effect against injuries of th

20、e hand or parts of it, such as torn capsules, broken fingers, sprained fingers and wrists. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest editio

21、n of the referenced document (including any amendments) applies. EN 420:2003+A1:2009, Protective gloves General requirements and test methods EN 10270-1 Steel wire for mechanical springs Part 1: Patented cold drawn unalloyed steel wire EN 13906-2, Cylindrical helical springs made from round wire and

22、 bar Calculation and design Part 2: Extension springs 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 glove for goal keepers protective equipment worn on the hand which restricts movement of the fingers further than the normal range of the jo

23、ints by use of additional safety features such as (but not restricted to) splints, braces or other stiffening elements 3.2 association football game of football in which the ball is not picked up or carried by field players, and in which the rules for tackling should limit the severity of body blows

24、 EN 13061:2009, 2.4 4 Requirements 4.1 General Gloves for goal keepers shall be safe and suitable for their purpose when used in accordance with the manufacturers instructions. They shall be free of hard or sharp edges or corners, buckles or other objects on the inside and the surface of the product

25、 which may be dangerous for the user or others during normal or foreseeable use when tested in accordance with 5.3. 4.2 Innocuousness Manufacturers of products complying with this standard should consider the health and protection of the user, the environment and the supply chain. Materials used sho

26、uld not, during foreseeable conditions of normal use, release or degrade to release substances generally known to be hazardous. BS EN 16027:2011EN 16027:2011 (E) 6 The manufacturer should list in the information supplied by the manufacturer the substances used for the main components of the product.

27、 NOTE Information on the identification and classification of such substances can be found in the Directive 67/548/EEC (classification, packaging and labelling of dangerous substances) 1 as well as in the Regulation (EC) no.1907/2006 of the European Parliament and of the Council of 18 December 2006

28、concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH)2. 4.3 Ergonomics Gloves for goalkeepers shall be designed in such a way that the user can perform the typical movements required by the foreseeable conditions of use without restrictions, closure systems whic

29、h ensure correct fitting and placement of the glove shall be adjustable and suitable to ensure restraint of the item whilst in use without constriction of the joint between the hand and arm. Testing shall be in accordance with 5.3. 4.4 Stiffness Gloves for goalkeepers shall be designed and manufactu

30、red with suitable stabilising and stiffening elements such that they support the fingers when they are stressed by a load or impact inverse to the natural flex direction of the fingers without endangering the hand, wrist or arm of the user. Testing shall be in accordance with 5.4, and the force meas

31、ured shall be within the limits specified in Table 1. 4.5 Restraint system Gloves for goalkeepers shall be easily fitted and adjusted by the user using a suitable restraint system. They shall fit firmly to the hand of the intended size, shall not release from the hand during use, and shall remain in

32、 the location they are designed to protect during all typical movements or impact. When tested in accordance with 5.5, the maximum displacement shall be less than 20 mm. 4.6 Impact strength Gloves for goal keepers with stabilizing and stiffening elements (e.g. splint, brace) shall be resistant again

33、st mechanical impacts. Stabilizing and stiffening elements shall not break or splinter, when tested according to 5.6. 4.7 Sizing Gloves shall be available in a range of sizes suitable for the varying hand size of the intended user. The manufacturer shall indicate the intended size for which the glov

34、e is designed. The size of the glove with protective effect shall be defined according to EN 420:2003+A1:2009, 5.1.2, Table 3. 5 Test methods 5.1 General Where no specific testing procedure is given, compliance with the requirements of this standard shall be established by measurement, visual and ph

35、ysical examination. For testing, new unused samples shall be used. Measuring instruments unless otherwise specified shall be accurate to 2 % of the pass/fail level of the characteristics being measured. BS EN 16027:2011EN 16027:2011 (E) 7 For each of the required sequences of measurement performed i

36、n accordance with this standard a corresponding estimate of the uncertainty of the final result shall be determined. The uncertainty of measurement shall be expressed in the form X. It shall be used in determining whether a “PASS” performance has been achieved. If the final result minus X is below t

37、he pass level and there is the requirement that a certain value shall be exceeded then the sample shall be deemed to have failed. NOTE It is anticipated that values of uncertainty of measurement will usually be between 2 % and 5 % of the measured value for force and length measurements. 5.2 Sampling

38、 and conditioning Two pairs of unused gloves for goal keepers of each size distributed to the market shall be provided for testing. The samples shall be conditioned for at least 24 h in an atmosphere of (20 2) C and a humidity of (65 5) %. Testing shall be carried out in the conditioning environment

39、 or within 10 min of removal from that environment. 5.3 Ergonomics At least two sizes of gloves, one sample each, shall be used. Each sample shall be put on and adjusted by a subject of appropriate dimensions of the intended user according to the information supplied by the manufacturer. Check by vi

40、sual and/or tactile inspection that the glove is free of hard or sharp edges or corners, seams and buckles and that the restraint system does not constrict the user in use. For testing the typical movements, a subject shall catch and fist a ball according to the rules of association football. The su

41、bject shall report any restrictions or severe discomfort when executing typical moves. The size of the gloves with protective effect shall be tested according to EN 420:2003+A1:2009, 6.1.3. 5.4 Stiffness 5.4.1 Apparatus The apparatus is illustrated in Figure 1. The apparatus comprises a palm support

42、 on which to place the palm of the glove to be tested and a finger support on which to place all fingers of the glove except the thumb. The finger support is attached to a pivot table lever. A scale enables measurement of the pivot angle of the lever with an accuracy of 1. The surfaces of the palm s

43、upport and of the finger support are on same level with accuracy of 0,2 mm. The pivot axis of the lever is (18 0,2) mm below the upper surface of the finger support. The apparatus further comprises a holding bar to press down the glove to the palm support. The surface of this bar facing the glove is

44、 plane with a radius of (3 0,1) mm on both long edges of the bar. The total width of the bar shall be 15 mm and the length minimum 200 mm. The long axis of the bar shall be parallel to the pivot axis with an accuracy of 0,5. The horizontal distance of long axis of the bar to the pivot axis shall be

45、(17,5 0,2) mm. A guiding system shall be provided to keep the holding bar in horizontal orientation with an accuracy of 1. The holding bar shall be weight loaded so that it shall be pressed down to the gloves upper surface with a force according to Table 1. A force to pivot the lever shall be applie

46、d radial to the pivot axis with a distance of (170 5) mm. The force shall be measured by a strain gauge or other appropriate instrumentation with an accuracy of 0,5 N. To replace the fingers of the hand, the fingers of the gloves except the thumb shall be filled with extension springs according to E

47、N 13906-2 with the following specifications: De=15 mm, d=1,5 mm, spring steel according to EN 10270-1, any grade, length min. 200 mm. BS EN 16027:2011EN 16027:2011 (E) 8 Key 1 palm support 2 finger support 3 pivotable lever 4 pivot axis 5 holding bar 6 weight 7 scale x1min. 170 mm x2170 mm 5 mm x370

48、 mm 0,2 mm x4see Table 1 x517,5 0,2 mm x615 0,1 mm z118 0,2 mm z212 0,2 mm r13 0,2 mm Figure 1 Apparatus for testing the stiffness of fingers of gloves BS EN 16027:2011EN 16027:2011 (E) 9 Key 1 palm support 2 finger support 3 pivotable lever 5 holding bar 6 weight 7 scale y1min. 200 mm y2min. 160 mm

49、 Figure 2 Perspective view of the apparatus for stiffness testing BS EN 16027:2011EN 16027:2011 (E) 10 Key 1 palm support 2 finger support 3 pivot table lever 4 pivot axis 5 holding bar 6 weight 7 scale 8 glove 9 tension spring 90 5 Figure 3 Principle of stiffness testing 5.4.2 Procedure With the hand of a test person of appropriate size inside the glove the position of all finger base joints (except thumb) shall be marked on the upp