EN 3155-057-2006 en Aerospace series Electrical contacts used in elements of connection Part 057 Contacts electrical female thermocouple NiCr type C crimp class T Product standard《.pdf

《EN 3155-057-2006 en Aerospace series Electrical contacts used in elements of connection Part 057 Contacts electrical female thermocouple NiCr type C crimp class T Product standard《.pdf》由会员分享，可在线阅读，更多相关《EN 3155-057-2006 en Aerospace series Electrical contacts used in elements of connection Part 057 Contacts electrical female thermocouple NiCr type C crimp class T Product standard《.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 3155-057:2006Aerospace series Electrical contacts used in elements of connection Part 057: Contacts, electrical, female, thermocouple NiCr, type C, crimp, class T Product standardThe European Standard EN 3155-057:2006 has the status of a British StandardICS 49.060g49g50g3g38g50

2、g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3155-057:2006This British Standard was published under the authority of the Standards Policy and Strategy Co

3、mmittee on 31 October 2006 BSI 2006ISBN 0 580 49469 1National forewordThis British Standard was published by BSI. It is the UK implementation of EN 3155-057:2006. The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technolo

4、gy, to Subcommittee ACE/6/-/3, Aerospace Connectors.A list of organizations represented on ACE/6/-/3 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with

5、a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3155-057July 2006ICS 49.060English VersionAerospace series - Electrical contacts used in elements ofconnection - Part 057: Conta

6、cts, electrical, female,thermocouple NiCr, type C, crimp, class T- Product standardSrie arospatiale - Contacts lectriques utiliss dans lesorganes de connexion - Partie 057 : Contacts lectriques,femelles, thermocouple NiCr, type C, sertir, classe T -Norme de produitLuft- und Raumfahrt - Elektrische K

7、ontakte zur Verwendungin Verbindungselementen - Teil 057: ElektrischeThermobuchsenkontakte NiCr, Typ C, crimpbar, Klasse T -ProduktnormThis European Standard was approved by CEN on 9 March 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions f

8、or giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official v

9、ersions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium,

10、Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCO

11、MIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3155-057:2006: E2 Contents Foreword3 1 Scope 4 2 Normative referenc

12、es 4 3 Definitions 5 4 Required characteristics.5 4.1 General5 4.2 Dimensions and mass.5 4.3 Marking by colour code 6 4.4 Material .7 4.5 Permissible cables.7 4.6 Tooling8 4.7 Cable stripping.8 4.8 Tests9 4.9 Quality assurance10 5 Designation 10 6 Marking .10 7 Technical specification .10 EN 3155-05

13、7:20063 Foreword This European Standard (EN 3155-057:2006) has been prepared by the AeroSpace and Defense Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of

14、the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2007, and conflicting

15、national standards shall be withdrawn at the latest by January 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the

16、CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembou

17、rg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3155-057:20064 1 Scope This standard specifies the required characteristics, tests and tooling applicable to female contacts, thermocouple, NiCr, type C, crimp, class

18、T, used in elements of connection according to EN 3155-002. It shall be used together with EN 3155-001. The associated male contacts are defined in EN 3155-056. 2 Normative references The following referenced documents are indispensable fort he application of this document. For dated references, onl

19、y the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591 (all parts), Aerospace series Elements of electrical and optical connection Test methods EN 3155-001, Aerospace series Electrical contacts used in elements o

20、f connection Part 001: Technical specification 1)EN 3155-002, Aerospace series Electrical contracts used in elements of connection Part 002: List and utilization of contacts EN 3155-056, Aerospace series Electrical contacts used in elements of connection Part 056: Contacts, electrical, male, thermoc

21、ouple NiCr, type C, crimp, class T Product standard 1)EN 4049 (all parts), Aerospace series Thermocouple extension cable Operating temperatures between -65 C and 260 ISO 8056-1, Aircraft Nickel-chromium and nickel-aluminium thermocouple extension cables Part 1: Conductors General requirements and te

22、sts ISO 8843, Aircraft Crimp-removable contacts for electrical connectors Identification system MIL-DTL-22520G, Crimping Tools, Wire Termination, General Specification for 2)MIL-C-22520/1C, Crimping Tools, Terminal, Hand, Wire Termination for Wire Barrel Sizes 12 through 20 2)MIL-C-22520/2C, Crimpin

23、g Tools, Terminal, Hand, Wire Termination for Wire Barrel Sizes 20 through 28 2)MIL-C-22520/7B, Crimping Tools, Terminal, Hand, Wire Termination for Wire Barrel Sizes 16, 20 and 22 2)MIL-I-81969B, Installing and Removal Tools, Connector Electrical Contacts, Type II, Class 2, Composition C 2)MIL-I-81

24、969/14C, Installing and Removal Tools, Connector Electrical Contact, Type III, Class 2, Composition B 2)MIL-I-81969/30, Installing and Removal Tools, Connector Electrical Contact, Type II, Class 2, Composition C, for Unwired Contacts 2)1) Published as AECMA Prestandard at the date of publication of

25、this standard. 2) Published by: Department of Defense (DOD), the Pentagon, Washington D.C. 20301 USA. EN 3155-057:20065 3 Definitions For the purposes of this standard, the definitions given in EN 3155-001 apply. 4 Required characteristics 4.1 General Type C contacts are for thermocouple application

26、. Class T corresponds to an operating temperature range from -65 C to 260 C. 4.2 Dimensions and mass See Figure 1, Figure 2 and Table 1. Dimensions in millimetres Key 1 Diameter H (one side only) 3 G max. See note 2. 2 0,25 max. See note 1. 4 Marking, see 4.3. NOTE 1 Clearance between sleeve and the

27、 body of the contact. NOTE 2 Position of the point of electrical contact. Figure 1 EN 3155-057:20066 Figure 2 Barrel, contact sizes 16-18 Table 1 Size A B C D E F G H Contact Barrel max. 20 20 16,66 12,32 12,17 4,34 4,06 0,84 0,74 1,98 1,93 1,05 1,14 0,81 0,66 20 18 16,66 12,32 12,17 4,34 4,06 0,84

28、0,74 1,98 1,93 1,05 1,14 0,81 0,66 16 16 19,28 12,70 12,55 6,53 6,25 1,22 1,12 2,87 2,79 1,63 1,27 1,07 0,91 16 18 19,28 12,70 12,55 6,53 6,25 1,22 1,12 2,87 2,79 1,63 1,27 1,07 0,91 Size J K L M N P T S Mass Contact Barrel min. g 20 20 1,68 1,57 4,72 3,99 1,27 1,22 1,98 1,93 2,62 2,54 1,52 1,73 1,3

29、5 0,31 20 18 1,68 1,57 4,72 3,99 1,35 1,30 1,98 1,93 2,62 2,54 1,52 1,73 1,35 0,31 16 16 2,26 2,11 7,21 6,35 1,73 1,68 2,62 2,56 3,38 3,30 2,21 2,16 1,73 0,68 16 18 1,68 1,57 7,21 6,35 1,35 1,30 1,98 1,93 3,38 3,30 2,21 2,16 1,73 2,62 2,56 0,68 4.3 Marking by colour code Marking shall be in accordan

30、ce with ISO 8843 and Table 2. Either the alloy type or coloured dot shall be used to identify the contact material. EN 3155-057:20067 Table 2 Size Colour Contact Barrel Band 1 Band 2 20 20 Red Red 20 18 Red Brown 16 16 Blue Blue 16 18 Blue Brown Key 1 White dot 2 Yellow dot 3 Band 1 4 Band 2 aAlloy

31、type identification to be produced by engraving, stamping or pressing without deformation of the contact. 4.4 Material NiCr (no protective plating) 4.5 Permissible cables Cables shall be in accordance with EN 4049-002 and Table 3. Table 3 Size Size of conductors Contact Barrel AECMA code Section mm

32、AWG a20 20 006 004 0,60 0,40 20 22 20 18 010 006 004 1,00 0,60 0,40 18 20 22 16 16 012 010 006 1,20 1,00 0,60 16 18 20 16 18 010 006 004 1,00 0,60 0,40 18 20 22 aAWG nearest American Wire Gauge. EN 3155-057:20068 4.6 Tooling 4.6.1 Crimping tools Conform to MIL-DTL-22520, see Table 4. The selector nu

33、mbers used for crimping Ni and Cr alloy conductors in cables EN 4049 are indicated in Table 4. These selector numbers shall be used for qualification of the contacts and in service, unless otherwise specified by the user. Table 4 Contact Cable size Tools M22520/1-01 Tools M22520/2-01 Tools M22520/7-

34、01 Contact size Barrel size AECMA code AWG aTurret Selector numberPositionerSelector numberPositioner Selector number004 22 3 6 5 20 20 006 20 M22520/1-02Red 4 M22520/2-027 M22520/7-02 6 004 22 3 6 5 006 20 4 7 6 20 18 010 18 M22520/1-02Red 5 M22520/2-028 M22520/7-02 7 006 20 4 5 010 18 5 6 16 16 01

35、2 16 M22520/1-02Blue 6 M22520/7-03 7 004 22 3 5 006 20 4 6 16 18 010 18 M22520/1-02Blue 5 Not applicable M22520/7-03 7 aAWG nearest American Wire Gauge. 4.6.2 Contact insertion/extraction tools Conforming to MIL-I-81969 and Table 5. Table 5 Size Extraction tools Contact Barrel Insertion tools Wired

36、contact Unwired contact 20 20 M81969/14-11 M81969/14-11 M81969/30-05 20 18 M81969/14-11 M81969/14-11 M81969/30-05 16 16 M81969/14-03 M81969/14-03 M81969/30-06 16 18 M81969/14-03 M81969/14-04 M81969/30-06 4.7 Cable stripping See Table 6. EN 3155-057:20069 Table 6 Size Contact Barrel Stripped length o

37、f cable mm 0,5 20 20 20 18 4,5 16 16 16 18 6,8 4.8 Tests See Table 7. Table 7 Applicable EN 2591- Designation of the test Not applicable According to EN 3155-001 Remarks 101 Visual examination X 102 Examination of dimensions and mass X 201 Contact resistance - low level X 220 Contact/Conductor joint

38、 ageing by current and temperature cycling X 301 Endurance at temperature X 305 Rapid change of temperature X TA = (-65 2) C TB = (260 2) C 307 Salt mist X 402 Shock X 403 Sinusoidal and random vibration X 406 Mechanical endurance X 415 Test probe damage (female contact) X 416 Contact bending streng

39、th X 417 Tensile strength (crimped connection) X 418 Gauge insertion and extraction forces in and out of a female contact X 502 Restricted entry X 503 Contact deformation after crimping X 507 Plating porosity X 508 Measurement of thickness of coating on contacts X EN 3155-057:200610 4.9 Quality assu

40、rance 4.9.1 Inspection conditions for manufacturing lots A sample shall be taken from each batch of wire or rod used to manufacture thermocouple contacts and tested in accordance with ISO 8056-1 except the thermo-electric tests on conductors of finished cables shall use the EMF measurement by method

41、 of direct comparison against platinum and not a substandard. 5 Designation EXAMPLE Description block Identity block CONTACT, ELECTRICAL EN3155-057 F 20 20 Number of this standard Type of contact: F: female Contact size (see Table 1) Barrel size (see Table 1) NOTE If necessary, the code I9005 shall

42、be placed between the description block and the identity block. 6 Marking See EN 3155-001. 7 Technical specification See EN 3155-001. EN 3155-057:2006blankBS EN 3155-057:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for pre

43、paring British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or edition

44、s.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside

45、 front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications sh

46、ould be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have b

47、een published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also avai

48、lable which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standar

49、ds. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copy